新商品! 到貨於 第1季 2027

• 與DCC的使用（DCC接口）

Rivet Counter HO Scale EMD GP30 Phase IIa, Louisville & Nashville/ex-C&EI Patched New roadname New paint scheme Era: Late 1960s Series L&N 1058 to 1060, ex-MP 590 to 592, ex-C&EI 239 to 241, Phase IIa, built 6/1963 Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-illuminated “hemisphere” walkway lights on hood ends, and at end of raised walkway duct* LED-illuminated tricolor front and rear flush-mounted class lights with lenses and raised gaskets** LED-illuminated, printed and backlit cab and long hood end number boards Front and rear multiple unit (MU) hose catch boxes 4-hose multiple unit (MU) hose clusters with silver gladhands Semi-scale coupler buffer equipped with durable metal semi-scale Type E knuckle couplers, painted a dingy gray/brown color to represent the color of couplers in service Front and rear straight uncoupling levers without loop handles As-delivered pilot faces without uncoupling lever loop notches Deck-mounted multiple unit (MU) receptacle “Short” stepwells with see-through steps Handrail set with center gangway chains Scale sectioned treadplate detail with EMD early “X” style pattern 81” GP30 low short hood with ratchet handbrake and square sand fill Hinged battery box doors with early hinges and narrow louvers Early cab sub-base doors with early hinges Front standard EMD LED-illuminated headlight with lenses on number board housing GP30 cab with increased length on left (fireman’s) side and inverted cab heater vents Detailed cab interior with separate floor, rear wall, seats, and standard AAR control stand No cab vents Sliding cab side windows Tall clear wind wings with mirror at bottom mounted fore of cab side window on both sides of cab Standard EMD sunshades with long sunshade tracks Lost-wax brass cast Nathan P-3 (P142 configuration) horn, mounted on number board housing “Whip” antenna mounted to center of cab roof Accurate hood door and long hood detail Late single-panel inertial compartment Stamped inertial air intake grills with vertical stiffeners Tall turbo exhaust stack Extended-range dynamic brakes with 48” fan Late see-through dynamic brake intake grills with horizontal wires through vertical vanes 7-horizontal rib radiator intake grills See-through front and rear 48” radiator fan housings with 8-blade fans; 36” pan-top center radiator fan Square sand fill hatch on top of long hood end Rear LED-illuminated horizontal headlight with lenses Underbody frame rail with separate plumbing Detailed Blomberg-B trucks with Hyatt bearing housings; elliptical springs; end transom detail; separate sanding lines and brackets; and separate swing hanger detail Wheel faces painted a dingy gray/brown color to represent the color of wheelsets in service Dimensionally accurate truck centers Speed recorder mounted to second axle on right front truck sideframe Frame-mounted bell No underbody air filter 2,600-gallon fuel tank with vertical gauges and fuel fill in sill skirt; round gauge in right side of fuel tank Factory-applied wire grab irons, photoetched lift rings, windshield wipers, trainline hoses with silver gladhands, air tanks, sand hatch covers, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended radius: 22” DCC & sound equipped locomotives also feature: ESU LokSound 5 DCC & Sound decoder with “Full Throttle” Two (2) cube-type speakers Prime mover sound Turbocharged 16-567D3 prime mover sound (original) ESU designed “PowerPack” with two super capacitors*** Operates on both DC and DCC layouts DC/DCC & sound-ready locomotives also feature: Operable on DC layouts DCC-ready with 21-pin connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC ** Class lights illuminate in white color only in DC operation. Access and changing colors requires an ESU decoder with appropriate programming while operating using DCC ***“PowerPack” feature only compatible with appropriately programmed ESU decoders operating on a DCC layout

商品重量: 1,320 kg

Angaben zur Produktsicherheit:
Hersteller: Scale Trains, 4901 Old Tasso Road NE Cleveland, TN 37312, USA, www.scaletrains.com
Verantwortlicher Importeur: RD-Hobby Modellbahnen, Jaegersburger Str. 17,68649 Gross-Rohrheim, Deutschland, email@RD-Hobby.de