• with DCC Decoder
• with Sound

DM&E/City of Lamberton New road numbers Era: As delivered 1976 to early 1980s Series 8035 to 8064;built 9-1976 Fully-assembled Multiple road numbers Class lights (non-operating) Saturn 6552 Strobe Light (non-operating) Printed and LED-illuminated number boards* Front tall pilot plow with high trainline hose cut out, multiple unit (MU) hose doors and grab irons 3-hose multiple unit (MU) hose clusters with silver gladhands Body mounted knuckle couplers; Micro-Trains® compatible Coupler box accepts Micro-Trains 1015/1016 couplers without modification Angled uncoupling levers front and rear and four inner mounting brackets As-delivered pilot faces with reinforced lifting holes Deck mounted multiple unit (MU) receptacle "Tall" stepwells Front and rear early small deck extension Handrail set with inward facing end rail mounting brackets and chain Standard front and rear drop steps Scale sectioned treadplate detail on walkways Rectangle walkway lights mounted between sandbox clean out doors (non-operating) 116” “snoot” low short hood with wheel handbrake Bolted battery box doors with wide louvers Late cab sub-base doors with lift-off hinges Front standard EMD LED-illuminated headlight in number board housing Dash two cab with bolted side window panels Detailed cab interior with floor, rear wall, seats, and standard AAR control stand Rear cab side vent on right side Tall clear wind wings with mirror at top mounted fore and aft of cab side window on both sides of cab Early awning type sunshade Lost wax brass cast Leslie RS-3-L horn with clearance bracket on long hood Motorola ASP-16 “Firecracker” antenna mounted on number board housing Early electrical cabinet "zig-zag" seam, further from rear of cab Early “stand-off” ECAFB Intermediate inertial air intake grills with top drip rail Standard turbo exhaust stack Accurately profiled extended-range dynamic brakes with batten strip Corrugated radiator intake grilles See-through standard 48” radiator fan housings with fan blades visible inside Drop grab radiator fan grab iron Underbody frame rail with separate plumbing and traction motor cables Detailed HT-C trucks with Hyatt bearing caps, late center axle snubbers, sanding lines and brackets GE type speed recorder mounted to third axle on left side Reward facing handbrake chain mount for HTC trucks Short jacking pads (late) Spare knuckle holders on fuel tank near fuel filler Forward engineer’s side sidesill notch Sill-mount EFCO Frame-mounted steel bell Graham-White (Salem) brand 824-170 and 818-170 primary and secondary centrifugal air filters (accordion-style) 4,000-gallon fuel tank with fuel fillers, vertical gauge and round gauge on stand Factory-applied wire grab irons, windshield wipers, trainline hoses with silver gladhands, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED headlights Printing and lettering legible even under magnification Operates on Code 55 and 80 rail Packaging safely stores model Minimum radius: 9 3/4” Recommended radius: 11” DCC & sound equipped locomotives also feature ESU LokSound 5 DCC & Sound decoder with “Full Throttle” One (1) cube-type speaker EMD 16 Cylinder 645E3 prime mover Operates on both DC and DCC layouts DC/DCC & sound ready locomotives also feature Operates on DC layouts DCC ready with E24 connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC

• Ready for use with DCC (DCC interface)

DM&E/City of Lamberton New road numbers Era: As delivered 1976 to early 1980s Series 8035 to 8064;built 9-1976 Fully-assembled Multiple road numbers Class lights (non-operating) Saturn 6552 Strobe Light (non-operating) Printed and LED-illuminated number boards* Front tall pilot plow with high trainline hose cut out, multiple unit (MU) hose doors and grab irons 3-hose multiple unit (MU) hose clusters with silver gladhands Body mounted knuckle couplers; Micro-Trains® compatible Coupler box accepts Micro-Trains 1015/1016 couplers without modification Angled uncoupling levers front and rear and four inner mounting brackets As-delivered pilot faces with reinforced lifting holes Deck mounted multiple unit (MU) receptacle "Tall" stepwells Front and rear early small deck extension Handrail set with inward facing end rail mounting brackets and chain Standard front and rear drop steps Scale sectioned treadplate detail on walkways Rectangle walkway lights mounted between sandbox clean out doors (non-operating) 116” “snoot” low short hood with wheel handbrake Bolted battery box doors with wide louvers Late cab sub-base doors with lift-off hinges Front standard EMD LED-illuminated headlight in number board housing Dash two cab with bolted side window panels Detailed cab interior with floor, rear wall, seats, and standard AAR control stand Rear cab side vent on right side Tall clear wind wings with mirror at top mounted fore and aft of cab side window on both sides of cab Early awning type sunshade Lost wax brass cast Leslie RS-3-L horn with clearance bracket on long hood Motorola ASP-16 “Firecracker” antenna mounted on number board housing Early electrical cabinet "zig-zag" seam, further from rear of cab Early “stand-off” ECAFB Intermediate inertial air intake grills with top drip rail Standard turbo exhaust stack Accurately profiled extended-range dynamic brakes with batten strip Corrugated radiator intake grilles See-through standard 48” radiator fan housings with fan blades visible inside Drop grab radiator fan grab iron Underbody frame rail with separate plumbing and traction motor cables Detailed HT-C trucks with Hyatt bearing caps, late center axle snubbers, sanding lines and brackets GE type speed recorder mounted to third axle on left side Reward facing handbrake chain mount for HTC trucks Short jacking pads (late) Spare knuckle holders on fuel tank near fuel filler Forward engineer’s side sidesill notch Sill-mount EFCO Frame-mounted steel bell Graham-White (Salem) brand 824-170 and 818-170 primary and secondary centrifugal air filters (accordion-style) 4,000-gallon fuel tank with fuel fillers, vertical gauge and round gauge on stand Factory-applied wire grab irons, windshield wipers, trainline hoses with silver gladhands, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED headlights Printing and lettering legible even under magnification Operates on Code 55 and 80 rail Packaging safely stores model Minimum radius: 9 3/4” Recommended radius: 11” DCC & sound equipped locomotives also feature ESU LokSound 5 DCC & Sound decoder with “Full Throttle” One (1) cube-type speaker EMD 16 Cylinder 645E3 prime mover Operates on both DC and DCC layouts DC/DCC & sound ready locomotives also feature Operates on DC layouts DCC ready with E24 connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC

• with DCC Decoder
• with Sound

New road numbers Era: As delivered 1976 to early 1980s Series 8035 to 8064;built 9-1976 Fully-assembled Multiple road numbers Class lights (non-operating) Saturn 6552 Strobe Light (non-operating) Printed and LED-illuminated number boards* Front tall pilot plow with high trainline hose cut out, multiple unit (MU) hose doors and grab irons 3-hose multiple unit (MU) hose clusters with silver gladhands Body mounted knuckle couplers; Micro-Trains® compatible Coupler box accepts Micro-Trains 1015/1016 couplers without modification Angled uncoupling levers front and rear and four inner mounting brackets As-delivered pilot faces with reinforced lifting holes Deck mounted multiple unit (MU) receptacle "Tall" stepwells Front and rear early small deck extension Handrail set with inward facing end rail mounting brackets and chain Standard front and rear drop steps Scale sectioned treadplate detail on walkways Rectangle walkway lights mounted between sandbox clean out doors (non-operating) 116” “snoot” low short hood with wheel handbrake Bolted battery box doors with wide louvers Late cab sub-base doors with lift-off hinges Front standard EMD LED-illuminated headlight in number board housing Dash two cab with bolted side window panels Detailed cab interior with floor, rear wall, seats, and standard AAR control stand Rear cab side vent on right side Tall clear wind wings with mirror at top mounted fore and aft of cab side window on both sides of cab Early awning type sunshade Lost wax brass cast Leslie RS-3-L horn with clearance bracket on long hood Motorola ASP-16 “Firecracker” antenna mounted on number board housing Early electrical cabinet "zig-zag" seam, further from rear of cab Early “stand-off” ECAFB Intermediate inertial air intake grills with top drip rail Standard turbo exhaust stack Accurately profiled extended-range dynamic brakes with batten strip Corrugated radiator intake grilles See-through standard 48” radiator fan housings with fan blades visible inside Drop grab radiator fan grab iron Underbody frame rail with separate plumbing and traction motor cables Detailed HT-C trucks with Hyatt bearing caps, late center axle snubbers, sanding lines and brackets GE type speed recorder mounted to third axle on left side Reward facing handbrake chain mount for HTC trucks Short jacking pads (late) Spare knuckle holders on fuel tank near fuel filler Forward engineer’s side sidesill notch Sill-mount EFCO Frame-mounted steel bell Graham-White (Salem) brand 824-170 and 818-170 primary and secondary centrifugal air filters (accordion-style) 4,000-gallon fuel tank with fuel fillers, vertical gauge and round gauge on stand Factory-applied wire grab irons, windshield wipers, trainline hoses with silver gladhands, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED headlights Printing and lettering legible even under magnification Operates on Code 55 and 80 rail Packaging safely stores model Minimum radius: 9 3/4” Recommended radius: 11” DCC & sound equipped locomotives also feature ESU LokSound 5 DCC & Sound decoder with “Full Throttle” One (1) cube-type speaker EMD 16 Cylinder 645E3 prime mover Operates on both DC and DCC layouts DC/DCC & sound ready locomotives also feature Operates on DC layouts DCC ready with E24 connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC

• Ready for use with DCC (DCC interface)

New road numbers Era: As delivered 1976 to early 1980s Series 8035 to 8064;built 9-1976 Fully-assembled Multiple road numbers Class lights (non-operating) Saturn 6552 Strobe Light (non-operating) Printed and LED-illuminated number boards* Front tall pilot plow with high trainline hose cut out, multiple unit (MU) hose doors and grab irons 3-hose multiple unit (MU) hose clusters with silver gladhands Body mounted knuckle couplers; Micro-Trains® compatible Coupler box accepts Micro-Trains 1015/1016 couplers without modification Angled uncoupling levers front and rear and four inner mounting brackets As-delivered pilot faces with reinforced lifting holes Deck mounted multiple unit (MU) receptacle "Tall" stepwells Front and rear early small deck extension Handrail set with inward facing end rail mounting brackets and chain Standard front and rear drop steps Scale sectioned treadplate detail on walkways Rectangle walkway lights mounted between sandbox clean out doors (non-operating) 116” “snoot” low short hood with wheel handbrake Bolted battery box doors with wide louvers Late cab sub-base doors with lift-off hinges Front standard EMD LED-illuminated headlight in number board housing Dash two cab with bolted side window panels Detailed cab interior with floor, rear wall, seats, and standard AAR control stand Rear cab side vent on right side Tall clear wind wings with mirror at top mounted fore and aft of cab side window on both sides of cab Early awning type sunshade Lost wax brass cast Leslie RS-3-L horn with clearance bracket on long hood Motorola ASP-16 “Firecracker” antenna mounted on number board housing Early electrical cabinet "zig-zag" seam, further from rear of cab Early “stand-off” ECAFB Intermediate inertial air intake grills with top drip rail Standard turbo exhaust stack Accurately profiled extended-range dynamic brakes with batten strip Corrugated radiator intake grilles See-through standard 48” radiator fan housings with fan blades visible inside Drop grab radiator fan grab iron Underbody frame rail with separate plumbing and traction motor cables Detailed HT-C trucks with Hyatt bearing caps, late center axle snubbers, sanding lines and brackets GE type speed recorder mounted to third axle on left side Reward facing handbrake chain mount for HTC trucks Short jacking pads (late) Spare knuckle holders on fuel tank near fuel filler Forward engineer’s side sidesill notch Sill-mount EFCO Frame-mounted steel bell Graham-White (Salem) brand 824-170 and 818-170 primary and secondary centrifugal air filters (accordion-style) 4,000-gallon fuel tank with fuel fillers, vertical gauge and round gauge on stand Factory-applied wire grab irons, windshield wipers, trainline hoses with silver gladhands, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED headlights Printing and lettering legible even under magnification Operates on Code 55 and 80 rail Packaging safely stores model Minimum radius: 9 3/4” Recommended radius: 11” DCC & sound equipped locomotives also feature ESU LokSound 5 DCC & Sound decoder with “Full Throttle” One (1) cube-type speaker EMD 16 Cylinder 645E3 prime mover Operates on both DC and DCC layouts DC/DCC & sound ready locomotives also feature Operates on DC layouts DCC ready with E24 connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC

• with DCC Decoder
• with Sound

DM&E/Mt. Rushmore New road numbers Era: As delivered 1976 to early 1980s Series 8035 to 8064;built 9-1976 Fully-assembled Multiple road numbers Class lights (non-operating) Saturn 6552 Strobe Light (non-operating) Printed and LED-illuminated number boards* Front tall pilot plow with high trainline hose cut out, multiple unit (MU) hose doors and grab irons 3-hose multiple unit (MU) hose clusters with silver gladhands Body mounted knuckle couplers; Micro-Trains® compatible Coupler box accepts Micro-Trains 1015/1016 couplers without modification Angled uncoupling levers front and rear and four inner mounting brackets As-delivered pilot faces with reinforced lifting holes Deck mounted multiple unit (MU) receptacle "Tall" stepwells Front and rear early small deck extension Handrail set with inward facing end rail mounting brackets and chain Standard front and rear drop steps Scale sectioned treadplate detail on walkways Rectangle walkway lights mounted between sandbox clean out doors (non-operating) 116” “snoot” low short hood with wheel handbrake Bolted battery box doors with wide louvers Late cab sub-base doors with lift-off hinges Front standard EMD LED-illuminated headlight in number board housing Dash two cab with bolted side window panels Detailed cab interior with floor, rear wall, seats, and standard AAR control stand Rear cab side vent on right side Tall clear wind wings with mirror at top mounted fore and aft of cab side window on both sides of cab Early awning type sunshade Lost wax brass cast Leslie RS-3-L horn with clearance bracket on long hood Motorola ASP-16 “Firecracker” antenna mounted on number board housing Early electrical cabinet "zig-zag" seam, further from rear of cab Early “stand-off” ECAFB Intermediate inertial air intake grills with top drip rail Standard turbo exhaust stack Accurately profiled extended-range dynamic brakes with batten strip Corrugated radiator intake grilles See-through standard 48” radiator fan housings with fan blades visible inside Drop grab radiator fan grab iron Underbody frame rail with separate plumbing and traction motor cables Detailed HT-C trucks with Hyatt bearing caps, late center axle snubbers, sanding lines and brackets GE type speed recorder mounted to third axle on left side Reward facing handbrake chain mount for HTC trucks Short jacking pads (late) Spare knuckle holders on fuel tank near fuel filler Forward engineer’s side sidesill notch Sill-mount EFCO Frame-mounted steel bell Graham-White (Salem) brand 824-170 and 818-170 primary and secondary centrifugal air filters (accordion-style) 4,000-gallon fuel tank with fuel fillers, vertical gauge and round gauge on stand Factory-applied wire grab irons, windshield wipers, trainline hoses with silver gladhands, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED headlights Printing and lettering legible even under magnification Operates on Code 55 and 80 rail Packaging safely stores model Minimum radius: 9 3/4” Recommended radius: 11” DCC & sound equipped locomotives also feature ESU LokSound 5 DCC & Sound decoder with “Full Throttle” One (1) cube-type speaker EMD 16 Cylinder 645E3 prime mover Operates on both DC and DCC layouts DC/DCC & sound ready locomotives also feature Operates on DC layouts DCC ready with E24 connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC

• Ready for use with DCC (DCC interface)

DM&E/Mt. Rushmore New road numbers Era: As delivered 1976 to early 1980s Series 8035 to 8064;built 9-1976 Fully-assembled Multiple road numbers Class lights (non-operating) Saturn 6552 Strobe Light (non-operating) Printed and LED-illuminated number boards* Front tall pilot plow with high trainline hose cut out, multiple unit (MU) hose doors and grab irons 3-hose multiple unit (MU) hose clusters with silver gladhands Body mounted knuckle couplers; Micro-Trains® compatible Coupler box accepts Micro-Trains 1015/1016 couplers without modification Angled uncoupling levers front and rear and four inner mounting brackets As-delivered pilot faces with reinforced lifting holes Deck mounted multiple unit (MU) receptacle "Tall" stepwells Front and rear early small deck extension Handrail set with inward facing end rail mounting brackets and chain Standard front and rear drop steps Scale sectioned treadplate detail on walkways Rectangle walkway lights mounted between sandbox clean out doors (non-operating) 116” “snoot” low short hood with wheel handbrake Bolted battery box doors with wide louvers Late cab sub-base doors with lift-off hinges Front standard EMD LED-illuminated headlight in number board housing Dash two cab with bolted side window panels Detailed cab interior with floor, rear wall, seats, and standard AAR control stand Rear cab side vent on right side Tall clear wind wings with mirror at top mounted fore and aft of cab side window on both sides of cab Early awning type sunshade Lost wax brass cast Leslie RS-3-L horn with clearance bracket on long hood Motorola ASP-16 “Firecracker” antenna mounted on number board housing Early electrical cabinet "zig-zag" seam, further from rear of cab Early “stand-off” ECAFB Intermediate inertial air intake grills with top drip rail Standard turbo exhaust stack Accurately profiled extended-range dynamic brakes with batten strip Corrugated radiator intake grilles See-through standard 48” radiator fan housings with fan blades visible inside Drop grab radiator fan grab iron Underbody frame rail with separate plumbing and traction motor cables Detailed HT-C trucks with Hyatt bearing caps, late center axle snubbers, sanding lines and brackets GE type speed recorder mounted to third axle on left side Reward facing handbrake chain mount for HTC trucks Short jacking pads (late) Spare knuckle holders on fuel tank near fuel filler Forward engineer’s side sidesill notch Sill-mount EFCO Frame-mounted steel bell Graham-White (Salem) brand 824-170 and 818-170 primary and secondary centrifugal air filters (accordion-style) 4,000-gallon fuel tank with fuel fillers, vertical gauge and round gauge on stand Factory-applied wire grab irons, windshield wipers, trainline hoses with silver gladhands, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED headlights Printing and lettering legible even under magnification Operates on Code 55 and 80 rail Packaging safely stores model Minimum radius: 9 3/4” Recommended radius: 11” DCC & sound equipped locomotives also feature ESU LokSound 5 DCC & Sound decoder with “Full Throttle” One (1) cube-type speaker EMD 16 Cylinder 645E3 prime mover Operates on both DC and DCC layouts DC/DCC & sound ready locomotives also feature Operates on DC layouts DCC ready with E24 connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC

• with DCC Decoder
• with Sound

CSX/YN3 Boxcar Logo/Yellow Plow New road numbers Era: As delivered 1976 to early 1980s Series 8035 to 8064;built 9-1976 Fully-assembled Multiple road numbers Class lights (non-operating) Saturn 6552 Strobe Light (non-operating) Printed and LED-illuminated number boards* Front tall pilot plow with high trainline hose cut out, multiple unit (MU) hose doors and grab irons 3-hose multiple unit (MU) hose clusters with silver gladhands Body mounted knuckle couplers; Micro-Trains® compatible Coupler box accepts Micro-Trains 1015/1016 couplers without modification Angled uncoupling levers front and rear and four inner mounting brackets As-delivered pilot faces with reinforced lifting holes Deck mounted multiple unit (MU) receptacle "Tall" stepwells Front and rear early small deck extension Handrail set with inward facing end rail mounting brackets and chain Standard front and rear drop steps Scale sectioned treadplate detail on walkways Rectangle walkway lights mounted between sandbox clean out doors (non-operating) 116” “snoot” low short hood with wheel handbrake Bolted battery box doors with wide louvers Late cab sub-base doors with lift-off hinges Front standard EMD LED-illuminated headlight in number board housing Dash two cab with bolted side window panels Detailed cab interior with floor, rear wall, seats, and standard AAR control stand Rear cab side vent on right side Tall clear wind wings with mirror at top mounted fore and aft of cab side window on both sides of cab Early awning type sunshade Lost wax brass cast Leslie RS-3-L horn with clearance bracket on long hood Motorola ASP-16 “Firecracker” antenna mounted on number board housing Early electrical cabinet "zig-zag" seam, further from rear of cab Early “stand-off” ECAFB Intermediate inertial air intake grills with top drip rail Standard turbo exhaust stack Accurately profiled extended-range dynamic brakes with batten strip Corrugated radiator intake grilles See-through standard 48” radiator fan housings with fan blades visible inside Drop grab radiator fan grab iron Underbody frame rail with separate plumbing and traction motor cables Detailed HT-C trucks with Hyatt bearing caps, late center axle snubbers, sanding lines and brackets GE type speed recorder mounted to third axle on left side Reward facing handbrake chain mount for HTC trucks Short jacking pads (late) Spare knuckle holders on fuel tank near fuel filler Forward engineer’s side sidesill notch Sill-mount EFCO Frame-mounted steel bell Graham-White (Salem) brand 824-170 and 818-170 primary and secondary centrifugal air filters (accordion-style) 4,000-gallon fuel tank with fuel fillers, vertical gauge and round gauge on stand Factory-applied wire grab irons, windshield wipers, trainline hoses with silver gladhands, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED headlights Printing and lettering legible even under magnification Operates on Code 55 and 80 rail Packaging safely stores model Minimum radius: 9 3/4” Recommended radius: 11” DCC & sound equipped locomotives also feature ESU LokSound 5 DCC & Sound decoder with “Full Throttle” One (1) cube-type speaker EMD 16 Cylinder 645E3 prime mover Operates on both DC and DCC layouts DC/DCC & sound ready locomotives also feature Operates on DC layouts DCC ready with E24 connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC

• Ready for use with DCC (DCC interface)

CSX/YN3 Boxcar Logo/Yellow Plow New road numbers Era: As delivered 1976 to early 1980s Series 8035 to 8064;built 9-1976 Fully-assembled Multiple road numbers Class lights (non-operating) Saturn 6552 Strobe Light (non-operating) Printed and LED-illuminated number boards* Front tall pilot plow with high trainline hose cut out, multiple unit (MU) hose doors and grab irons 3-hose multiple unit (MU) hose clusters with silver gladhands Body mounted knuckle couplers; Micro-Trains® compatible Coupler box accepts Micro-Trains 1015/1016 couplers without modification Angled uncoupling levers front and rear and four inner mounting brackets As-delivered pilot faces with reinforced lifting holes Deck mounted multiple unit (MU) receptacle "Tall" stepwells Front and rear early small deck extension Handrail set with inward facing end rail mounting brackets and chain Standard front and rear drop steps Scale sectioned treadplate detail on walkways Rectangle walkway lights mounted between sandbox clean out doors (non-operating) 116” “snoot” low short hood with wheel handbrake Bolted battery box doors with wide louvers Late cab sub-base doors with lift-off hinges Front standard EMD LED-illuminated headlight in number board housing Dash two cab with bolted side window panels Detailed cab interior with floor, rear wall, seats, and standard AAR control stand Rear cab side vent on right side Tall clear wind wings with mirror at top mounted fore and aft of cab side window on both sides of cab Early awning type sunshade Lost wax brass cast Leslie RS-3-L horn with clearance bracket on long hood Motorola ASP-16 “Firecracker” antenna mounted on number board housing Early electrical cabinet "zig-zag" seam, further from rear of cab Early “stand-off” ECAFB Intermediate inertial air intake grills with top drip rail Standard turbo exhaust stack Accurately profiled extended-range dynamic brakes with batten strip Corrugated radiator intake grilles See-through standard 48” radiator fan housings with fan blades visible inside Drop grab radiator fan grab iron Underbody frame rail with separate plumbing and traction motor cables Detailed HT-C trucks with Hyatt bearing caps, late center axle snubbers, sanding lines and brackets GE type speed recorder mounted to third axle on left side Reward facing handbrake chain mount for HTC trucks Short jacking pads (late) Spare knuckle holders on fuel tank near fuel filler Forward engineer’s side sidesill notch Sill-mount EFCO Frame-mounted steel bell Graham-White (Salem) brand 824-170 and 818-170 primary and secondary centrifugal air filters (accordion-style) 4,000-gallon fuel tank with fuel fillers, vertical gauge and round gauge on stand Factory-applied wire grab irons, windshield wipers, trainline hoses with silver gladhands, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED headlights Printing and lettering legible even under magnification Operates on Code 55 and 80 rail Packaging safely stores model Minimum radius: 9 3/4” Recommended radius: 11” DCC & sound equipped locomotives also feature ESU LokSound 5 DCC & Sound decoder with “Full Throttle” One (1) cube-type speaker EMD 16 Cylinder 645E3 prime mover Operates on both DC and DCC layouts DC/DCC & sound ready locomotives also feature Operates on DC layouts DCC ready with E24 connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC

• with DCC Decoder
• with Sound

CSX/YN3 Boxcar Logo New road numbers Era: As delivered 1976 to early 1980s Series 8035 to 8064;built 9-1976 Fully-assembled Multiple road numbers Class lights (non-operating) Saturn 6552 Strobe Light (non-operating) Printed and LED-illuminated number boards* Front tall pilot plow with high trainline hose cut out, multiple unit (MU) hose doors and grab irons 3-hose multiple unit (MU) hose clusters with silver gladhands Body mounted knuckle couplers; Micro-Trains® compatible Coupler box accepts Micro-Trains 1015/1016 couplers without modification Angled uncoupling levers front and rear and four inner mounting brackets As-delivered pilot faces with reinforced lifting holes Deck mounted multiple unit (MU) receptacle "Tall" stepwells Front and rear early small deck extension Handrail set with inward facing end rail mounting brackets and chain Standard front and rear drop steps Scale sectioned treadplate detail on walkways Rectangle walkway lights mounted between sandbox clean out doors (non-operating) 116” “snoot” low short hood with wheel handbrake Bolted battery box doors with wide louvers Late cab sub-base doors with lift-off hinges Front standard EMD LED-illuminated headlight in number board housing Dash two cab with bolted side window panels Detailed cab interior with floor, rear wall, seats, and standard AAR control stand Rear cab side vent on right side Tall clear wind wings with mirror at top mounted fore and aft of cab side window on both sides of cab Early awning type sunshade Lost wax brass cast Leslie RS-3-L horn with clearance bracket on long hood Motorola ASP-16 “Firecracker” antenna mounted on number board housing Early electrical cabinet "zig-zag" seam, further from rear of cab Early “stand-off” ECAFB Intermediate inertial air intake grills with top drip rail Standard turbo exhaust stack Accurately profiled extended-range dynamic brakes with batten strip Corrugated radiator intake grilles See-through standard 48” radiator fan housings with fan blades visible inside Drop grab radiator fan grab iron Underbody frame rail with separate plumbing and traction motor cables Detailed HT-C trucks with Hyatt bearing caps, late center axle snubbers, sanding lines and brackets GE type speed recorder mounted to third axle on left side Reward facing handbrake chain mount for HTC trucks Short jacking pads (late) Spare knuckle holders on fuel tank near fuel filler Forward engineer’s side sidesill notch Sill-mount EFCO Frame-mounted steel bell Graham-White (Salem) brand 824-170 and 818-170 primary and secondary centrifugal air filters (accordion-style) 4,000-gallon fuel tank with fuel fillers, vertical gauge and round gauge on stand Factory-applied wire grab irons, windshield wipers, trainline hoses with silver gladhands, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED headlights Printing and lettering legible even under magnification Operates on Code 55 and 80 rail Packaging safely stores model Minimum radius: 9 3/4” Recommended radius: 11” DCC & sound equipped locomotives also feature ESU LokSound 5 DCC & Sound decoder with “Full Throttle” One (1) cube-type speaker EMD 16 Cylinder 645E3 prime mover Operates on both DC and DCC layouts DC/DCC & sound ready locomotives also feature Operates on DC layouts DCC ready with E24 connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC

• with DCC Decoder
• with Sound

CSX/YN3 Boxcar Logo New road numbers Era: As delivered 1976 to early 1980s Series 8035 to 8064;built 9-1976 Fully-assembled Multiple road numbers Class lights (non-operating) Saturn 6552 Strobe Light (non-operating) Printed and LED-illuminated number boards* Front tall pilot plow with high trainline hose cut out, multiple unit (MU) hose doors and grab irons 3-hose multiple unit (MU) hose clusters with silver gladhands Body mounted knuckle couplers; Micro-Trains® compatible Coupler box accepts Micro-Trains 1015/1016 couplers without modification Angled uncoupling levers front and rear and four inner mounting brackets As-delivered pilot faces with reinforced lifting holes Deck mounted multiple unit (MU) receptacle "Tall" stepwells Front and rear early small deck extension Handrail set with inward facing end rail mounting brackets and chain Standard front and rear drop steps Scale sectioned treadplate detail on walkways Rectangle walkway lights mounted between sandbox clean out doors (non-operating) 116” “snoot” low short hood with wheel handbrake Bolted battery box doors with wide louvers Late cab sub-base doors with lift-off hinges Front standard EMD LED-illuminated headlight in number board housing Dash two cab with bolted side window panels Detailed cab interior with floor, rear wall, seats, and standard AAR control stand Rear cab side vent on right side Tall clear wind wings with mirror at top mounted fore and aft of cab side window on both sides of cab Early awning type sunshade Lost wax brass cast Leslie RS-3-L horn with clearance bracket on long hood Motorola ASP-16 “Firecracker” antenna mounted on number board housing Early electrical cabinet "zig-zag" seam, further from rear of cab Early “stand-off” ECAFB Intermediate inertial air intake grills with top drip rail Standard turbo exhaust stack Accurately profiled extended-range dynamic brakes with batten strip Corrugated radiator intake grilles See-through standard 48” radiator fan housings with fan blades visible inside Drop grab radiator fan grab iron Underbody frame rail with separate plumbing and traction motor cables Detailed HT-C trucks with Hyatt bearing caps, late center axle snubbers, sanding lines and brackets GE type speed recorder mounted to third axle on left side Reward facing handbrake chain mount for HTC trucks Short jacking pads (late) Spare knuckle holders on fuel tank near fuel filler Forward engineer’s side sidesill notch Sill-mount EFCO Frame-mounted steel bell Graham-White (Salem) brand 824-170 and 818-170 primary and secondary centrifugal air filters (accordion-style) 4,000-gallon fuel tank with fuel fillers, vertical gauge and round gauge on stand Factory-applied wire grab irons, windshield wipers, trainline hoses with silver gladhands, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED headlights Printing and lettering legible even under magnification Operates on Code 55 and 80 rail Packaging safely stores model Minimum radius: 9 3/4” Recommended radius: 11” DCC & sound equipped locomotives also feature ESU LokSound 5 DCC & Sound decoder with “Full Throttle” One (1) cube-type speaker EMD 16 Cylinder 645E3 prime mover Operates on both DC and DCC layouts DC/DCC & sound ready locomotives also feature Operates on DC layouts DCC ready with E24 connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC

• Ready for use with DCC (DCC interface)

CSX/YN3 Boxcar Logo New road numbers Era: As delivered 1976 to early 1980s Series 8035 to 8064;built 9-1976 Fully-assembled Multiple road numbers Class lights (non-operating) Saturn 6552 Strobe Light (non-operating) Printed and LED-illuminated number boards* Front tall pilot plow with high trainline hose cut out, multiple unit (MU) hose doors and grab irons 3-hose multiple unit (MU) hose clusters with silver gladhands Body mounted knuckle couplers; Micro-Trains® compatible Coupler box accepts Micro-Trains 1015/1016 couplers without modification Angled uncoupling levers front and rear and four inner mounting brackets As-delivered pilot faces with reinforced lifting holes Deck mounted multiple unit (MU) receptacle "Tall" stepwells Front and rear early small deck extension Handrail set with inward facing end rail mounting brackets and chain Standard front and rear drop steps Scale sectioned treadplate detail on walkways Rectangle walkway lights mounted between sandbox clean out doors (non-operating) 116” “snoot” low short hood with wheel handbrake Bolted battery box doors with wide louvers Late cab sub-base doors with lift-off hinges Front standard EMD LED-illuminated headlight in number board housing Dash two cab with bolted side window panels Detailed cab interior with floor, rear wall, seats, and standard AAR control stand Rear cab side vent on right side Tall clear wind wings with mirror at top mounted fore and aft of cab side window on both sides of cab Early awning type sunshade Lost wax brass cast Leslie RS-3-L horn with clearance bracket on long hood Motorola ASP-16 “Firecracker” antenna mounted on number board housing Early electrical cabinet "zig-zag" seam, further from rear of cab Early “stand-off” ECAFB Intermediate inertial air intake grills with top drip rail Standard turbo exhaust stack Accurately profiled extended-range dynamic brakes with batten strip Corrugated radiator intake grilles See-through standard 48” radiator fan housings with fan blades visible inside Drop grab radiator fan grab iron Underbody frame rail with separate plumbing and traction motor cables Detailed HT-C trucks with Hyatt bearing caps, late center axle snubbers, sanding lines and brackets GE type speed recorder mounted to third axle on left side Reward facing handbrake chain mount for HTC trucks Short jacking pads (late) Spare knuckle holders on fuel tank near fuel filler Forward engineer’s side sidesill notch Sill-mount EFCO Frame-mounted steel bell Graham-White (Salem) brand 824-170 and 818-170 primary and secondary centrifugal air filters (accordion-style) 4,000-gallon fuel tank with fuel fillers, vertical gauge and round gauge on stand Factory-applied wire grab irons, windshield wipers, trainline hoses with silver gladhands, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED headlights Printing and lettering legible even under magnification Operates on Code 55 and 80 rail Packaging safely stores model Minimum radius: 9 3/4” Recommended radius: 11” DCC & sound equipped locomotives also feature ESU LokSound 5 DCC & Sound decoder with “Full Throttle” One (1) cube-type speaker EMD 16 Cylinder 645E3 prime mover Operates on both DC and DCC layouts DC/DCC & sound ready locomotives also feature Operates on DC layouts DCC ready with E24 connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC

• Ready for use with DCC (DCC interface)

CSX/YN3 Boxcar Logo New road numbers Era: As delivered 1976 to early 1980s Series 8035 to 8064;built 9-1976 Fully-assembled Multiple road numbers Class lights (non-operating) Saturn 6552 Strobe Light (non-operating) Printed and LED-illuminated number boards* Front tall pilot plow with high trainline hose cut out, multiple unit (MU) hose doors and grab irons 3-hose multiple unit (MU) hose clusters with silver gladhands Body mounted knuckle couplers; Micro-Trains® compatible Coupler box accepts Micro-Trains 1015/1016 couplers without modification Angled uncoupling levers front and rear and four inner mounting brackets As-delivered pilot faces with reinforced lifting holes Deck mounted multiple unit (MU) receptacle "Tall" stepwells Front and rear early small deck extension Handrail set with inward facing end rail mounting brackets and chain Standard front and rear drop steps Scale sectioned treadplate detail on walkways Rectangle walkway lights mounted between sandbox clean out doors (non-operating) 116” “snoot” low short hood with wheel handbrake Bolted battery box doors with wide louvers Late cab sub-base doors with lift-off hinges Front standard EMD LED-illuminated headlight in number board housing Dash two cab with bolted side window panels Detailed cab interior with floor, rear wall, seats, and standard AAR control stand Rear cab side vent on right side Tall clear wind wings with mirror at top mounted fore and aft of cab side window on both sides of cab Early awning type sunshade Lost wax brass cast Leslie RS-3-L horn with clearance bracket on long hood Motorola ASP-16 “Firecracker” antenna mounted on number board housing Early electrical cabinet "zig-zag" seam, further from rear of cab Early “stand-off” ECAFB Intermediate inertial air intake grills with top drip rail Standard turbo exhaust stack Accurately profiled extended-range dynamic brakes with batten strip Corrugated radiator intake grilles See-through standard 48” radiator fan housings with fan blades visible inside Drop grab radiator fan grab iron Underbody frame rail with separate plumbing and traction motor cables Detailed HT-C trucks with Hyatt bearing caps, late center axle snubbers, sanding lines and brackets GE type speed recorder mounted to third axle on left side Reward facing handbrake chain mount for HTC trucks Short jacking pads (late) Spare knuckle holders on fuel tank near fuel filler Forward engineer’s side sidesill notch Sill-mount EFCO Frame-mounted steel bell Graham-White (Salem) brand 824-170 and 818-170 primary and secondary centrifugal air filters (accordion-style) 4,000-gallon fuel tank with fuel fillers, vertical gauge and round gauge on stand Factory-applied wire grab irons, windshield wipers, trainline hoses with silver gladhands, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED headlights Printing and lettering legible even under magnification Operates on Code 55 and 80 rail Packaging safely stores model Minimum radius: 9 3/4” Recommended radius: 11” DCC & sound equipped locomotives also feature ESU LokSound 5 DCC & Sound decoder with “Full Throttle” One (1) cube-type speaker EMD 16 Cylinder 645E3 prime mover Operates on both DC and DCC layouts DC/DCC & sound ready locomotives also feature Operates on DC layouts DCC ready with E24 connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC

• with DCC Decoder
• with Sound

BNSF/Heritage/Small Circle-Cross Nose Logo New road numbers Era: As delivered 1976 to early 1980s Series 8035 to 8064;built 9-1976 Fully-assembled Multiple road numbers Class lights (non-operating) Saturn 6552 Strobe Light (non-operating) Printed and LED-illuminated number boards* Front tall pilot plow with high trainline hose cut out, multiple unit (MU) hose doors and grab irons 3-hose multiple unit (MU) hose clusters with silver gladhands Body mounted knuckle couplers; Micro-Trains® compatible Coupler box accepts Micro-Trains 1015/1016 couplers without modification Angled uncoupling levers front and rear and four inner mounting brackets As-delivered pilot faces with reinforced lifting holes Deck mounted multiple unit (MU) receptacle "Tall" stepwells Front and rear early small deck extension Handrail set with inward facing end rail mounting brackets and chain Standard front and rear drop steps Scale sectioned treadplate detail on walkways Rectangle walkway lights mounted between sandbox clean out doors (non-operating) 116” “snoot” low short hood with wheel handbrake Bolted battery box doors with wide louvers Late cab sub-base doors with lift-off hinges Front standard EMD LED-illuminated headlight in number board housing Dash two cab with bolted side window panels Detailed cab interior with floor, rear wall, seats, and standard AAR control stand Rear cab side vent on right side Tall clear wind wings with mirror at top mounted fore and aft of cab side window on both sides of cab Early awning type sunshade Lost wax brass cast Leslie RS-3-L horn with clearance bracket on long hood Motorola ASP-16 “Firecracker” antenna mounted on number board housing Early electrical cabinet "zig-zag" seam, further from rear of cab Early “stand-off” ECAFB Intermediate inertial air intake grills with top drip rail Standard turbo exhaust stack Accurately profiled extended-range dynamic brakes with batten strip Corrugated radiator intake grilles See-through standard 48” radiator fan housings with fan blades visible inside Drop grab radiator fan grab iron Underbody frame rail with separate plumbing and traction motor cables Detailed HT-C trucks with Hyatt bearing caps, late center axle snubbers, sanding lines and brackets GE type speed recorder mounted to third axle on left side Reward facing handbrake chain mount for HTC trucks Short jacking pads (late) Spare knuckle holders on fuel tank near fuel filler Forward engineer’s side sidesill notch Sill-mount EFCO Frame-mounted steel bell Graham-White (Salem) brand 824-170 and 818-170 primary and secondary centrifugal air filters (accordion-style) 4,000-gallon fuel tank with fuel fillers, vertical gauge and round gauge on stand Factory-applied wire grab irons, windshield wipers, trainline hoses with silver gladhands, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED headlights Printing and lettering legible even under magnification Operates on Code 55 and 80 rail Packaging safely stores model Minimum radius: 9 3/4” Recommended radius: 11” DCC & sound equipped locomotives also feature ESU LokSound 5 DCC & Sound decoder with “Full Throttle” One (1) cube-type speaker EMD 16 Cylinder 645E3 prime mover Operates on both DC and DCC layouts DC/DCC & sound ready locomotives also feature Operates on DC layouts DCC ready with E24 connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC

• with DCC Decoder
• with Sound

BNSF/Heritage/Small Circle-Cross Nose Logo New road numbers Era: As delivered 1976 to early 1980s Series 8035 to 8064;built 9-1976 Fully-assembled Multiple road numbers Class lights (non-operating) Saturn 6552 Strobe Light (non-operating) Printed and LED-illuminated number boards* Front tall pilot plow with high trainline hose cut out, multiple unit (MU) hose doors and grab irons 3-hose multiple unit (MU) hose clusters with silver gladhands Body mounted knuckle couplers; Micro-Trains® compatible Coupler box accepts Micro-Trains 1015/1016 couplers without modification Angled uncoupling levers front and rear and four inner mounting brackets As-delivered pilot faces with reinforced lifting holes Deck mounted multiple unit (MU) receptacle "Tall" stepwells Front and rear early small deck extension Handrail set with inward facing end rail mounting brackets and chain Standard front and rear drop steps Scale sectioned treadplate detail on walkways Rectangle walkway lights mounted between sandbox clean out doors (non-operating) 116” “snoot” low short hood with wheel handbrake Bolted battery box doors with wide louvers Late cab sub-base doors with lift-off hinges Front standard EMD LED-illuminated headlight in number board housing Dash two cab with bolted side window panels Detailed cab interior with floor, rear wall, seats, and standard AAR control stand Rear cab side vent on right side Tall clear wind wings with mirror at top mounted fore and aft of cab side window on both sides of cab Early awning type sunshade Lost wax brass cast Leslie RS-3-L horn with clearance bracket on long hood Motorola ASP-16 “Firecracker” antenna mounted on number board housing Early electrical cabinet "zig-zag" seam, further from rear of cab Early “stand-off” ECAFB Intermediate inertial air intake grills with top drip rail Standard turbo exhaust stack Accurately profiled extended-range dynamic brakes with batten strip Corrugated radiator intake grilles See-through standard 48” radiator fan housings with fan blades visible inside Drop grab radiator fan grab iron Underbody frame rail with separate plumbing and traction motor cables Detailed HT-C trucks with Hyatt bearing caps, late center axle snubbers, sanding lines and brackets GE type speed recorder mounted to third axle on left side Reward facing handbrake chain mount for HTC trucks Short jacking pads (late) Spare knuckle holders on fuel tank near fuel filler Forward engineer’s side sidesill notch Sill-mount EFCO Frame-mounted steel bell Graham-White (Salem) brand 824-170 and 818-170 primary and secondary centrifugal air filters (accordion-style) 4,000-gallon fuel tank with fuel fillers, vertical gauge and round gauge on stand Factory-applied wire grab irons, windshield wipers, trainline hoses with silver gladhands, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED headlights Printing and lettering legible even under magnification Operates on Code 55 and 80 rail Packaging safely stores model Minimum radius: 9 3/4” Recommended radius: 11” DCC & sound equipped locomotives also feature ESU LokSound 5 DCC & Sound decoder with “Full Throttle” One (1) cube-type speaker EMD 16 Cylinder 645E3 prime mover Operates on both DC and DCC layouts DC/DCC & sound ready locomotives also feature Operates on DC layouts DCC ready with E24 connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC

• Ready for use with DCC (DCC interface)

BNSF/Heritage/Small Circle-Cross Nose Logo New road numbers Era: As delivered 1976 to early 1980s Series 8035 to 8064;built 9-1976 Fully-assembled Multiple road numbers Class lights (non-operating) Saturn 6552 Strobe Light (non-operating) Printed and LED-illuminated number boards* Front tall pilot plow with high trainline hose cut out, multiple unit (MU) hose doors and grab irons 3-hose multiple unit (MU) hose clusters with silver gladhands Body mounted knuckle couplers; Micro-Trains® compatible Coupler box accepts Micro-Trains 1015/1016 couplers without modification Angled uncoupling levers front and rear and four inner mounting brackets As-delivered pilot faces with reinforced lifting holes Deck mounted multiple unit (MU) receptacle "Tall" stepwells Front and rear early small deck extension Handrail set with inward facing end rail mounting brackets and chain Standard front and rear drop steps Scale sectioned treadplate detail on walkways Rectangle walkway lights mounted between sandbox clean out doors (non-operating) 116” “snoot” low short hood with wheel handbrake Bolted battery box doors with wide louvers Late cab sub-base doors with lift-off hinges Front standard EMD LED-illuminated headlight in number board housing Dash two cab with bolted side window panels Detailed cab interior with floor, rear wall, seats, and standard AAR control stand Rear cab side vent on right side Tall clear wind wings with mirror at top mounted fore and aft of cab side window on both sides of cab Early awning type sunshade Lost wax brass cast Leslie RS-3-L horn with clearance bracket on long hood Motorola ASP-16 “Firecracker” antenna mounted on number board housing Early electrical cabinet "zig-zag" seam, further from rear of cab Early “stand-off” ECAFB Intermediate inertial air intake grills with top drip rail Standard turbo exhaust stack Accurately profiled extended-range dynamic brakes with batten strip Corrugated radiator intake grilles See-through standard 48” radiator fan housings with fan blades visible inside Drop grab radiator fan grab iron Underbody frame rail with separate plumbing and traction motor cables Detailed HT-C trucks with Hyatt bearing caps, late center axle snubbers, sanding lines and brackets GE type speed recorder mounted to third axle on left side Reward facing handbrake chain mount for HTC trucks Short jacking pads (late) Spare knuckle holders on fuel tank near fuel filler Forward engineer’s side sidesill notch Sill-mount EFCO Frame-mounted steel bell Graham-White (Salem) brand 824-170 and 818-170 primary and secondary centrifugal air filters (accordion-style) 4,000-gallon fuel tank with fuel fillers, vertical gauge and round gauge on stand Factory-applied wire grab irons, windshield wipers, trainline hoses with silver gladhands, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED headlights Printing and lettering legible even under magnification Operates on Code 55 and 80 rail Packaging safely stores model Minimum radius: 9 3/4” Recommended radius: 11” DCC & sound equipped locomotives also feature ESU LokSound 5 DCC & Sound decoder with “Full Throttle” One (1) cube-type speaker EMD 16 Cylinder 645E3 prime mover Operates on both DC and DCC layouts DC/DCC & sound ready locomotives also feature Operates on DC layouts DCC ready with E24 connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC

• with DCC Decoder
• with Sound

BNSF/Heritage I/Large Circle-Cross Nose Logo New road numbers Era: As delivered 1976 to early 1980s Series 8035 to 8064;built 9-1976 Fully-assembled Multiple road numbers Class lights (non-operating) Saturn 6552 Strobe Light (non-operating) Printed and LED-illuminated number boards* Front tall pilot plow with high trainline hose cut out, multiple unit (MU) hose doors and grab irons 3-hose multiple unit (MU) hose clusters with silver gladhands Body mounted knuckle couplers; Micro-Trains® compatible Coupler box accepts Micro-Trains 1015/1016 couplers without modification Angled uncoupling levers front and rear and four inner mounting brackets As-delivered pilot faces with reinforced lifting holes Deck mounted multiple unit (MU) receptacle "Tall" stepwells Front and rear early small deck extension Handrail set with inward facing end rail mounting brackets and chain Standard front and rear drop steps Scale sectioned treadplate detail on walkways Rectangle walkway lights mounted between sandbox clean out doors (non-operating) 116” “snoot” low short hood with wheel handbrake Bolted battery box doors with wide louvers Late cab sub-base doors with lift-off hinges Front standard EMD LED-illuminated headlight in number board housing Dash two cab with bolted side window panels Detailed cab interior with floor, rear wall, seats, and standard AAR control stand Rear cab side vent on right side Tall clear wind wings with mirror at top mounted fore and aft of cab side window on both sides of cab Early awning type sunshade Lost wax brass cast Leslie RS-3-L horn with clearance bracket on long hood Motorola ASP-16 “Firecracker” antenna mounted on number board housing Early electrical cabinet "zig-zag" seam, further from rear of cab Early “stand-off” ECAFB Intermediate inertial air intake grills with top drip rail Standard turbo exhaust stack Accurately profiled extended-range dynamic brakes with batten strip Corrugated radiator intake grilles See-through standard 48” radiator fan housings with fan blades visible inside Drop grab radiator fan grab iron Underbody frame rail with separate plumbing and traction motor cables Detailed HT-C trucks with Hyatt bearing caps, late center axle snubbers, sanding lines and brackets GE type speed recorder mounted to third axle on left side Reward facing handbrake chain mount for HTC trucks Short jacking pads (late) Spare knuckle holders on fuel tank near fuel filler Forward engineer’s side sidesill notch Sill-mount EFCO Frame-mounted steel bell Graham-White (Salem) brand 824-170 and 818-170 primary and secondary centrifugal air filters (accordion-style) 4,000-gallon fuel tank with fuel fillers, vertical gauge and round gauge on stand Factory-applied wire grab irons, windshield wipers, trainline hoses with silver gladhands, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED headlights Printing and lettering legible even under magnification Operates on Code 55 and 80 rail Packaging safely stores model Minimum radius: 9 3/4” Recommended radius: 11” DCC & sound equipped locomotives also feature ESU LokSound 5 DCC & Sound decoder with “Full Throttle” One (1) cube-type speaker EMD 16 Cylinder 645E3 prime mover Operates on both DC and DCC layouts DC/DCC & sound ready locomotives also feature Operates on DC layouts DCC ready with E24 connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC

• with DCC Decoder
• with Sound

BNSF/Heritage I/Large Circle-Cross Nose Logo New road numbers Era: As delivered 1976 to early 1980s Series 8035 to 8064;built 9-1976 Fully-assembled Multiple road numbers Class lights (non-operating) Saturn 6552 Strobe Light (non-operating) Printed and LED-illuminated number boards* Front tall pilot plow with high trainline hose cut out, multiple unit (MU) hose doors and grab irons 3-hose multiple unit (MU) hose clusters with silver gladhands Body mounted knuckle couplers; Micro-Trains® compatible Coupler box accepts Micro-Trains 1015/1016 couplers without modification Angled uncoupling levers front and rear and four inner mounting brackets As-delivered pilot faces with reinforced lifting holes Deck mounted multiple unit (MU) receptacle "Tall" stepwells Front and rear early small deck extension Handrail set with inward facing end rail mounting brackets and chain Standard front and rear drop steps Scale sectioned treadplate detail on walkways Rectangle walkway lights mounted between sandbox clean out doors (non-operating) 116” “snoot” low short hood with wheel handbrake Bolted battery box doors with wide louvers Late cab sub-base doors with lift-off hinges Front standard EMD LED-illuminated headlight in number board housing Dash two cab with bolted side window panels Detailed cab interior with floor, rear wall, seats, and standard AAR control stand Rear cab side vent on right side Tall clear wind wings with mirror at top mounted fore and aft of cab side window on both sides of cab Early awning type sunshade Lost wax brass cast Leslie RS-3-L horn with clearance bracket on long hood Motorola ASP-16 “Firecracker” antenna mounted on number board housing Early electrical cabinet "zig-zag" seam, further from rear of cab Early “stand-off” ECAFB Intermediate inertial air intake grills with top drip rail Standard turbo exhaust stack Accurately profiled extended-range dynamic brakes with batten strip Corrugated radiator intake grilles See-through standard 48” radiator fan housings with fan blades visible inside Drop grab radiator fan grab iron Underbody frame rail with separate plumbing and traction motor cables Detailed HT-C trucks with Hyatt bearing caps, late center axle snubbers, sanding lines and brackets GE type speed recorder mounted to third axle on left side Reward facing handbrake chain mount for HTC trucks Short jacking pads (late) Spare knuckle holders on fuel tank near fuel filler Forward engineer’s side sidesill notch Sill-mount EFCO Frame-mounted steel bell Graham-White (Salem) brand 824-170 and 818-170 primary and secondary centrifugal air filters (accordion-style) 4,000-gallon fuel tank with fuel fillers, vertical gauge and round gauge on stand Factory-applied wire grab irons, windshield wipers, trainline hoses with silver gladhands, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED headlights Printing and lettering legible even under magnification Operates on Code 55 and 80 rail Packaging safely stores model Minimum radius: 9 3/4” Recommended radius: 11” DCC & sound equipped locomotives also feature ESU LokSound 5 DCC & Sound decoder with “Full Throttle” One (1) cube-type speaker EMD 16 Cylinder 645E3 prime mover Operates on both DC and DCC layouts DC/DCC & sound ready locomotives also feature Operates on DC layouts DCC ready with E24 connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC

• Ready for use with DCC (DCC interface)

BNSF/Heritage I/Large Circle-Cross Nose Logo New road numbers Era: As delivered 1976 to early 1980s Series 8035 to 8064;built 9-1976 Fully-assembled Multiple road numbers Class lights (non-operating) Saturn 6552 Strobe Light (non-operating) Printed and LED-illuminated number boards* Front tall pilot plow with high trainline hose cut out, multiple unit (MU) hose doors and grab irons 3-hose multiple unit (MU) hose clusters with silver gladhands Body mounted knuckle couplers; Micro-Trains® compatible Coupler box accepts Micro-Trains 1015/1016 couplers without modification Angled uncoupling levers front and rear and four inner mounting brackets As-delivered pilot faces with reinforced lifting holes Deck mounted multiple unit (MU) receptacle "Tall" stepwells Front and rear early small deck extension Handrail set with inward facing end rail mounting brackets and chain Standard front and rear drop steps Scale sectioned treadplate detail on walkways Rectangle walkway lights mounted between sandbox clean out doors (non-operating) 116” “snoot” low short hood with wheel handbrake Bolted battery box doors with wide louvers Late cab sub-base doors with lift-off hinges Front standard EMD LED-illuminated headlight in number board housing Dash two cab with bolted side window panels Detailed cab interior with floor, rear wall, seats, and standard AAR control stand Rear cab side vent on right side Tall clear wind wings with mirror at top mounted fore and aft of cab side window on both sides of cab Early awning type sunshade Lost wax brass cast Leslie RS-3-L horn with clearance bracket on long hood Motorola ASP-16 “Firecracker” antenna mounted on number board housing Early electrical cabinet "zig-zag" seam, further from rear of cab Early “stand-off” ECAFB Intermediate inertial air intake grills with top drip rail Standard turbo exhaust stack Accurately profiled extended-range dynamic brakes with batten strip Corrugated radiator intake grilles See-through standard 48” radiator fan housings with fan blades visible inside Drop grab radiator fan grab iron Underbody frame rail with separate plumbing and traction motor cables Detailed HT-C trucks with Hyatt bearing caps, late center axle snubbers, sanding lines and brackets GE type speed recorder mounted to third axle on left side Reward facing handbrake chain mount for HTC trucks Short jacking pads (late) Spare knuckle holders on fuel tank near fuel filler Forward engineer’s side sidesill notch Sill-mount EFCO Frame-mounted steel bell Graham-White (Salem) brand 824-170 and 818-170 primary and secondary centrifugal air filters (accordion-style) 4,000-gallon fuel tank with fuel fillers, vertical gauge and round gauge on stand Factory-applied wire grab irons, windshield wipers, trainline hoses with silver gladhands, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED headlights Printing and lettering legible even under magnification Operates on Code 55 and 80 rail Packaging safely stores model Minimum radius: 9 3/4” Recommended radius: 11” DCC & sound equipped locomotives also feature ESU LokSound 5 DCC & Sound decoder with “Full Throttle” One (1) cube-type speaker EMD 16 Cylinder 645E3 prime mover Operates on both DC and DCC layouts DC/DCC & sound ready locomotives also feature Operates on DC layouts DCC ready with E24 connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC

• Ready for use with DCC (DCC interface)

BNSF/Heritage I/Large Circle-Cross Nose Logo New road numbers Era: As delivered 1976 to early 1980s Series 8035 to 8064;built 9-1976 Fully-assembled Multiple road numbers Class lights (non-operating) Saturn 6552 Strobe Light (non-operating) Printed and LED-illuminated number boards* Front tall pilot plow with high trainline hose cut out, multiple unit (MU) hose doors and grab irons 3-hose multiple unit (MU) hose clusters with silver gladhands Body mounted knuckle couplers; Micro-Trains® compatible Coupler box accepts Micro-Trains 1015/1016 couplers without modification Angled uncoupling levers front and rear and four inner mounting brackets As-delivered pilot faces with reinforced lifting holes Deck mounted multiple unit (MU) receptacle "Tall" stepwells Front and rear early small deck extension Handrail set with inward facing end rail mounting brackets and chain Standard front and rear drop steps Scale sectioned treadplate detail on walkways Rectangle walkway lights mounted between sandbox clean out doors (non-operating) 116” “snoot” low short hood with wheel handbrake Bolted battery box doors with wide louvers Late cab sub-base doors with lift-off hinges Front standard EMD LED-illuminated headlight in number board housing Dash two cab with bolted side window panels Detailed cab interior with floor, rear wall, seats, and standard AAR control stand Rear cab side vent on right side Tall clear wind wings with mirror at top mounted fore and aft of cab side window on both sides of cab Early awning type sunshade Lost wax brass cast Leslie RS-3-L horn with clearance bracket on long hood Motorola ASP-16 “Firecracker” antenna mounted on number board housing Early electrical cabinet "zig-zag" seam, further from rear of cab Early “stand-off” ECAFB Intermediate inertial air intake grills with top drip rail Standard turbo exhaust stack Accurately profiled extended-range dynamic brakes with batten strip Corrugated radiator intake grilles See-through standard 48” radiator fan housings with fan blades visible inside Drop grab radiator fan grab iron Underbody frame rail with separate plumbing and traction motor cables Detailed HT-C trucks with Hyatt bearing caps, late center axle snubbers, sanding lines and brackets GE type speed recorder mounted to third axle on left side Reward facing handbrake chain mount for HTC trucks Short jacking pads (late) Spare knuckle holders on fuel tank near fuel filler Forward engineer’s side sidesill notch Sill-mount EFCO Frame-mounted steel bell Graham-White (Salem) brand 824-170 and 818-170 primary and secondary centrifugal air filters (accordion-style) 4,000-gallon fuel tank with fuel fillers, vertical gauge and round gauge on stand Factory-applied wire grab irons, windshield wipers, trainline hoses with silver gladhands, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED headlights Printing and lettering legible even under magnification Operates on Code 55 and 80 rail Packaging safely stores model Minimum radius: 9 3/4” Recommended radius: 11” DCC & sound equipped locomotives also feature ESU LokSound 5 DCC & Sound decoder with “Full Throttle” One (1) cube-type speaker EMD 16 Cylinder 645E3 prime mover Operates on both DC and DCC layouts DC/DCC & sound ready locomotives also feature Operates on DC layouts DCC ready with E24 connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC

Innovation! Delivery June 2026

• with DCC Decoder
• with Sound

New road numbers Era: 2016 to Present Series 8091 to 8140; built 2012 Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-illuminated front, rear and rectangle side walkway lights* LED-illuminated front and rear deck-mounted alternating ditch lights** Printed and LED lighted number boards* LSL (Locomotive Speed Limiter) indicator lights on cab sides (non-operating) Sill-mounted brake stick holder Semi-scale coupler buffers equipped with die-cast metal semi-scale Type E knuckle couplers Inside loop uncoupling levers with up down brackets Single trainline hose with silver gladhand Pilot-mounted battery charging receptacles Dual front dummy Multiple Unit (MU) receptacles mounted to pilot face Front raised and rear flush pilot-mounted Multiple Unit (MU) receptacles Front and rear single ECP brake equipment box and cable mounted on pilot face See-through round-hole stepwell steps Walkway with front anticlimber; no support brackets GE “nub” pattern walkway tread Late handrails with U-bolt caps and narrow rear most stanchion on long side rails Wide profile end handrails Sand box clean out door with knuckle buster latch and hinge Front high (cab) mounted headlight Front straight grab irons mounted directly to the nose Right nose door without window Front high-mounted (cab) numberboard housings Dual cab side blue flag holder Left side under cab front access bolted X panel; rear door with square corrugated grille Late cab with barrel bolt latches on subbase doors Detailed cab interior with separate floor, rear wall, seats, and control stand In cab grade crossing camera mounted on right side Tinted cab side windows Tall mirror mounted in front of sliding cab side windows on both sides Switching mirror mounted between rear of sliding cab side windows and fixed rear window on engineer’s side Cab roof JEM Communications PTC antenna farm with single large Sinclair antenna Inverter Cabinet with Bolted and hinged access door, top two X panels same size, three lower X panels with 4 - 6 - 4 Bolt Pattern See-through dynamic brake exhaust Left side dynamic brake cab: tri blower dynamic brake with flush exhaust Etched metal see-through dynamic brake intake grilles with blower motors visible inside Right side dynamic brake cab: door with grille, small grille, door with grille, and door with grille Dynamic brake cab door with high door handle and high mounted door handle bumper Short right side air intake grille Left side auxiliary cab: 3 tall doors with latches on the #2 door and long auxiliary cab filter box door Right side auxiliary cab: 4 doors with latches on #1 and #4 doors ES44 style engine cab doors: latched first door in each set of three Three engine cab roof lift rings Lost wax brass cast Nathan AirChime K5HL horn mounted on engine cab roof ES44 style exhaust stack Left side exhaust cab doors: latched last door in set of three Flush heat exchanger housing with two-piece wide slot grille Late raised radiator grille 22 individually applied etched metal see-through radiator intake and exhaust grilles on sides and top of radiator compartment Left side radiator cab grille arrangement: Raised doors. Grilles - tall-short-tall-short-tall, no grille under brake wheel short front angled grille and two-piece rear angled grille Right side radiator cab grille arrangement: Raised doors. Grilles – tall, short, tall, short, short, tall, short, tall, short front angled grill, two-piece rear angled grille Flat water fill box with sight glass High mounted horizontal rear headlight Rear anticlimber without support brackets Rear wide-spaced dual dummy Multiple Unit (MU) receptacles Accurately profiled frame with separately applied plumbing and cabling GE Hi-Ad trucks with separately applied brake cylinders, single bracket air plumbing, and rotating bearing caps and smooth section in sideframe over center axle Rust-color painted wheelsets Curved handbrake chain bracket Toilet drain with interior handle AEI tag mounted on bracket below the right sidesill Dual Graham-White (Prime) finned 075 air filters Graham-White 994-500 air dryer 5,300-gallon fuel tank with internal waste retention tank, digital fuel gauge, vertical fuel gauge, and round fuel gauge Dual fuel fills per side with rear fill “blanked” Angled top left side fuel tank top box Digital Fuel Gauges Short crankcase drainpipe Factory-applied wire grab irons, snowplow with grab irons, spare knuckles, trainline hoses with silver gladhands, 3-hose MU clusters with silver gladhands, uncoupling levers, windshield wipers, mirrors, sunshades, air tanks, fuel tank mounted electronic bell, brake wheel, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED headlights Printing and lettering legible under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum Radius: 18” Recommended Radius: 22” DCC & sound equipped locomotives also feature: ESU-LokSound 5 DCC and Sound decoder with “Full Throttle” Two (2) cube-type speakers Accurate GEVO-12 prime mover and auxiliary sounds, horn, bell, and more ESU-designed PowerPack with two (2) super capacitors*** Operates on both DC and DCC layouts DCC & sound ready locomotives also feature: Operate using DC DCC ready with 21-pin connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC ** In DC operation, both front ditch lights illuminate; rear ditch lights (if equipped) do not illuminate *** Compatible with appropriately programmed ESU decoders while operating using DCC