• mit DCC Motordekoder
• mit Sound

New paint scheme Era: 2024 to present Road number 1875 Special Pittsburgh & Lake Erie Heritage scheme Series 3000 to 3064; built 4-6:2012 Former CSX 3063 Inverter Cabinet with Bolted and hinged access door, Front Top X Panel Wider Than Rear X Panel, three lower X panels with 4 - 6 - 4 Bolt Pattern Lower X Panels Lost wax brass cast Nathan AirChime K5HLR2 horn mounted on engine cab roof As delivered ES44 style exhaust stack with large flange and center support Fully-assembled LED-illuminated ground lights on both sides of locomotive* LED-illuminated front, rear and rectangle side walkway lights* LED-illuminated front deck-mounted alternating ditch lights** Printed and LED-illuminated lighted number boards* LSL (Locomotive Speed Limiter) indicator lights on cab sides (non-operating) Sill-mounted tow chain Semi-scale coupler buffers equipped with die-cast metal semi-scale SBE bottom shelf knuckle couplers Inside loop uncoupling levers with up down brackets Single trainline hose with silver gladhand Pilot-mounted battery charging receptacles Front dummy Multiple Unit (MU) receptacles mounted to pilot face Front and rear raised pilot-mounted Multiple Unit (MU) receptacles Front and rear single ECP brake equipment box and cable mounted on pilot face See-through round-hole stepwell steps Walkway with front anticlimber; no support brackets GE “nub” pattern walkway tread Late handrails with U-bolt caps and narrow rear most stanchion on long side rails Wide profile end handrails Sand box clean out door with knuckle buster latch Front nose headlight Front straight grab irons mounted directly to the nose Front right side mounted narrow nose drop grab iron Right nose door with window Front high-mounted (cab) numberboard housing Dual cab side blue flag holder Left side under cab front access bolted X panel; rear door with square corrugated grille Late cab with barrel bolt latches on subbase doors Detailed cab interior with separate floor, rear wall, seats, and control stand In cab grade crossing camera mounted on right side Tinted cab side windows Tall mirror mounted in front of sliding cab side windows on both sides Switching mirror mounted between rear of sliding cab side windows and fixed rear window on engineer’s side Cab roof GE communications handler octagonal dome and dual long STI-CO PTC Dual Track Antenna System without Radome covers See-through dynamic brake exhaust Left side dynamic brake cab: tri blower dynamic brake with flush exhaust Etched metal see-through dynamic brake intake grilles with blower motors visible inside Right side dynamic brake cab: door with grille, small grille, door with grille, and door with grille Dynamic brake cab door with high door handle and high mounted door handle bumper Long right side air intake grille Left side auxiliary cab: 3 tall doors with latches on the #2 door and no auxiliary cab filter box door Right side auxiliary cab: raised X panel door; 3 doors with latches on #2 and #3 doors ES44 style engine cab doors: latched first door in each set of three Three engine cab roof lift rings Left side exhaust cab doors: latched last door in set of three Flush heat exchanger housing with single piece narrow slot grille Raised radiator grille 22 individually applied etched metal see-through radiator intake and exhaust grilles on sides and top of radiator compartment Left side radiator cab grille arrangement: Raised doors. Grilles - tall-short-tall-short-tall, no grille under brake wheel short front angled grille and two-piece rear angled grille Right side radiator cab grille arrangement: Raised doors. Grilles – tall, short, tall, short, short, tall, short, tall, short front angled grill, two-piece rear angled grille Flat water fill box with sight glass High mounted horizontal rear headlight Rear narrow-spaced dual dummy Multiple Unit (MU) receptacles Accurately profiled frame with separately applied plumbing and cabling Late GE steerable trucks with separately applied brake cylinders, air plumbing, rotating bearing caps, and reinforcement bar under center journal Rust-color painted wheelsets Square handbrake chain bracket Toilet drain with exterior handle AEI tag mounted to right sidesill Dual Graham-White (Prime) finned 075 air filters Graham-White 994-500 air dryer 5,300-gallon fuel tank with internal waste retention tank, digital fuel gauge, vertical fuel gauge, and round fuel gauge Dual fuel fills per side with rear fill “blanked” Flat top left side fuel tank top box Long crankcase drainpipe attached to the end of the fuel tank Tall snowplow without MU doors Factory-applied wire grab irons, snowplow with grab irons, spare knuckles, trainline hoses with silver gladhands, 3-hose MU clusters with silver gladhands, uncoupling levers, windshield wipers, mirrors, sunshades, air tanks, fuel tank mounted electronic bell, brake wheel, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED headlights Printing and lettering legible under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum Radius: 18” Recommended Radius: 22” DCC & sound equipped locomotives also feature: ESU-LokSound 5 DCC and Sound decoder with “Full Throttle” Two (2) cube-type speakers Accurate GEVO-12 prime mover and auxiliary sounds, horn, bell, and more ESU-designed PowerPack with two (2) super capacitors*** Operates on both DC and DCC layouts DCC & sound ready locomotives also feature: Operate using DC DCC ready with 21-pin connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC ** In DC operation, both front ditch lights illuminate; rear ditch lights (if equipped) do not illuminate *** Compatible with appropriately programmed ESU decoders while operating using DCC

• mit DCC Motordekoder
• mit Sound

New paint scheme Era: 2024 to present Road number 1875 Special Pittsburgh & Lake Erie Heritage scheme Series 3000 to 3064; built 4-6:2012 Former CSX 3063 Inverter Cabinet with Bolted and hinged access door, Front Top X Panel Wider Than Rear X Panel, three lower X panels with 4 - 6 - 4 Bolt Pattern Lower X Panels Lost wax brass cast Nathan AirChime K5HLR2 horn mounted on engine cab roof As delivered ES44 style exhaust stack with large flange and center support Fully-assembled LED-illuminated ground lights on both sides of locomotive* LED-illuminated front, rear and rectangle side walkway lights* LED-illuminated front deck-mounted alternating ditch lights** Printed and LED-illuminated lighted number boards* LSL (Locomotive Speed Limiter) indicator lights on cab sides (non-operating) Sill-mounted tow chain Semi-scale coupler buffers equipped with die-cast metal semi-scale SBE bottom shelf knuckle couplers Inside loop uncoupling levers with up down brackets Single trainline hose with silver gladhand Pilot-mounted battery charging receptacles Front dummy Multiple Unit (MU) receptacles mounted to pilot face Front and rear raised pilot-mounted Multiple Unit (MU) receptacles Front and rear single ECP brake equipment box and cable mounted on pilot face See-through round-hole stepwell steps Walkway with front anticlimber; no support brackets GE “nub” pattern walkway tread Late handrails with U-bolt caps and narrow rear most stanchion on long side rails Wide profile end handrails Sand box clean out door with knuckle buster latch Front nose headlight Front straight grab irons mounted directly to the nose Front right side mounted narrow nose drop grab iron Right nose door with window Front high-mounted (cab) numberboard housing Dual cab side blue flag holder Left side under cab front access bolted X panel; rear door with square corrugated grille Late cab with barrel bolt latches on subbase doors Detailed cab interior with separate floor, rear wall, seats, and control stand In cab grade crossing camera mounted on right side Tinted cab side windows Tall mirror mounted in front of sliding cab side windows on both sides Switching mirror mounted between rear of sliding cab side windows and fixed rear window on engineer’s side Cab roof GE communications handler octagonal dome and dual long STI-CO PTC Dual Track Antenna System without Radome covers See-through dynamic brake exhaust Left side dynamic brake cab: tri blower dynamic brake with flush exhaust Etched metal see-through dynamic brake intake grilles with blower motors visible inside Right side dynamic brake cab: door with grille, small grille, door with grille, and door with grille Dynamic brake cab door with high door handle and high mounted door handle bumper Long right side air intake grille Left side auxiliary cab: 3 tall doors with latches on the #2 door and no auxiliary cab filter box door Right side auxiliary cab: raised X panel door; 3 doors with latches on #2 and #3 doors ES44 style engine cab doors: latched first door in each set of three Three engine cab roof lift rings Left side exhaust cab doors: latched last door in set of three Flush heat exchanger housing with single piece narrow slot grille Raised radiator grille 22 individually applied etched metal see-through radiator intake and exhaust grilles on sides and top of radiator compartment Left side radiator cab grille arrangement: Raised doors. Grilles - tall-short-tall-short-tall, no grille under brake wheel short front angled grille and two-piece rear angled grille Right side radiator cab grille arrangement: Raised doors. Grilles – tall, short, tall, short, short, tall, short, tall, short front angled grill, two-piece rear angled grille Flat water fill box with sight glass High mounted horizontal rear headlight Rear narrow-spaced dual dummy Multiple Unit (MU) receptacles Accurately profiled frame with separately applied plumbing and cabling Late GE steerable trucks with separately applied brake cylinders, air plumbing, rotating bearing caps, and reinforcement bar under center journal Rust-color painted wheelsets Square handbrake chain bracket Toilet drain with exterior handle AEI tag mounted to right sidesill Dual Graham-White (Prime) finned 075 air filters Graham-White 994-500 air dryer 5,300-gallon fuel tank with internal waste retention tank, digital fuel gauge, vertical fuel gauge, and round fuel gauge Dual fuel fills per side with rear fill “blanked” Flat top left side fuel tank top box Long crankcase drainpipe attached to the end of the fuel tank Tall snowplow without MU doors Factory-applied wire grab irons, snowplow with grab irons, spare knuckles, trainline hoses with silver gladhands, 3-hose MU clusters with silver gladhands, uncoupling levers, windshield wipers, mirrors, sunshades, air tanks, fuel tank mounted electronic bell, brake wheel, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED headlights Printing and lettering legible under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum Radius: 18” Recommended Radius: 22” DCC & sound equipped locomotives also feature: ESU-LokSound 5 DCC and Sound decoder with “Full Throttle” Two (2) cube-type speakers Accurate GEVO-12 prime mover and auxiliary sounds, horn, bell, and more ESU-designed PowerPack with two (2) super capacitors*** Operates on both DC and DCC layouts DCC & sound ready locomotives also feature: Operate using DC DCC ready with 21-pin connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC ** In DC operation, both front ditch lights illuminate; rear ditch lights (if equipped) do not illuminate *** Compatible with appropriately programmed ESU decoders while operating using DCC

• mit DCC Motordekoder
• mit Sound

New paint scheme Era: 2024 to present Road number 1875 Special Pittsburgh & Lake Erie Heritage scheme Series 3000 to 3064; built 4-6:2012 Former CSX 3063 Inverter Cabinet with Bolted and hinged access door, Front Top X Panel Wider Than Rear X Panel, three lower X panels with 4 - 6 - 4 Bolt Pattern Lower X Panels Lost wax brass cast Nathan AirChime K5HLR2 horn mounted on engine cab roof As delivered ES44 style exhaust stack with large flange and center support Fully-assembled LED-illuminated ground lights on both sides of locomotive* LED-illuminated front, rear and rectangle side walkway lights* LED-illuminated front deck-mounted alternating ditch lights** Printed and LED-illuminated lighted number boards* LSL (Locomotive Speed Limiter) indicator lights on cab sides (non-operating) Sill-mounted tow chain Semi-scale coupler buffers equipped with die-cast metal semi-scale SBE bottom shelf knuckle couplers Inside loop uncoupling levers with up down brackets Single trainline hose with silver gladhand Pilot-mounted battery charging receptacles Front dummy Multiple Unit (MU) receptacles mounted to pilot face Front and rear raised pilot-mounted Multiple Unit (MU) receptacles Front and rear single ECP brake equipment box and cable mounted on pilot face See-through round-hole stepwell steps Walkway with front anticlimber; no support brackets GE “nub” pattern walkway tread Late handrails with U-bolt caps and narrow rear most stanchion on long side rails Wide profile end handrails Sand box clean out door with knuckle buster latch Front nose headlight Front straight grab irons mounted directly to the nose Front right side mounted narrow nose drop grab iron Right nose door with window Front high-mounted (cab) numberboard housing Dual cab side blue flag holder Left side under cab front access bolted X panel; rear door with square corrugated grille Late cab with barrel bolt latches on subbase doors Detailed cab interior with separate floor, rear wall, seats, and control stand In cab grade crossing camera mounted on right side Tinted cab side windows Tall mirror mounted in front of sliding cab side windows on both sides Switching mirror mounted between rear of sliding cab side windows and fixed rear window on engineer’s side Cab roof GE communications handler octagonal dome and dual long STI-CO PTC Dual Track Antenna System without Radome covers See-through dynamic brake exhaust Left side dynamic brake cab: tri blower dynamic brake with flush exhaust Etched metal see-through dynamic brake intake grilles with blower motors visible inside Right side dynamic brake cab: door with grille, small grille, door with grille, and door with grille Dynamic brake cab door with high door handle and high mounted door handle bumper Long right side air intake grille Left side auxiliary cab: 3 tall doors with latches on the #2 door and no auxiliary cab filter box door Right side auxiliary cab: raised X panel door; 3 doors with latches on #2 and #3 doors ES44 style engine cab doors: latched first door in each set of three Three engine cab roof lift rings Left side exhaust cab doors: latched last door in set of three Flush heat exchanger housing with single piece narrow slot grille Raised radiator grille 22 individually applied etched metal see-through radiator intake and exhaust grilles on sides and top of radiator compartment Left side radiator cab grille arrangement: Raised doors. Grilles - tall-short-tall-short-tall, no grille under brake wheel short front angled grille and two-piece rear angled grille Right side radiator cab grille arrangement: Raised doors. Grilles – tall, short, tall, short, short, tall, short, tall, short front angled grill, two-piece rear angled grille Flat water fill box with sight glass High mounted horizontal rear headlight Rear narrow-spaced dual dummy Multiple Unit (MU) receptacles Accurately profiled frame with separately applied plumbing and cabling Late GE steerable trucks with separately applied brake cylinders, air plumbing, rotating bearing caps, and reinforcement bar under center journal Rust-color painted wheelsets Square handbrake chain bracket Toilet drain with exterior handle AEI tag mounted to right sidesill Dual Graham-White (Prime) finned 075 air filters Graham-White 994-500 air dryer 5,300-gallon fuel tank with internal waste retention tank, digital fuel gauge, vertical fuel gauge, and round fuel gauge Dual fuel fills per side with rear fill “blanked” Flat top left side fuel tank top box Long crankcase drainpipe attached to the end of the fuel tank Tall snowplow without MU doors Factory-applied wire grab irons, snowplow with grab irons, spare knuckles, trainline hoses with silver gladhands, 3-hose MU clusters with silver gladhands, uncoupling levers, windshield wipers, mirrors, sunshades, air tanks, fuel tank mounted electronic bell, brake wheel, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED headlights Printing and lettering legible under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum Radius: 18” Recommended Radius: 22” DCC & sound equipped locomotives also feature: ESU-LokSound 5 DCC and Sound decoder with “Full Throttle” Two (2) cube-type speakers Accurate GEVO-12 prime mover and auxiliary sounds, horn, bell, and more ESU-designed PowerPack with two (2) super capacitors*** Operates on both DC and DCC layouts DCC & sound ready locomotives also feature: Operate using DC DCC ready with 21-pin connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC ** In DC operation, both front ditch lights illuminate; rear ditch lights (if equipped) do not illuminate *** Compatible with appropriately programmed ESU decoders while operating using DCC

• mit DCC Motordekoder
• mit Sound

New paint scheme Era: Late 80s to Mid-90s Series ATSF 2746 to 2785 (rebuilt between 1982-1984) ATSF 2777 “Faded” ATSF Yellow w/ fresh paint touch-ups at various locations Mounting flanges from removed inertial air intake hoods remaining on long hood roof behind cab EOT antenna stand on right side of cab roof ATSF 2785 “Faded” ATSF Yellow w/ fresh paint touch-ups at various locations Mounting flanges from removed inertial air intake hoods remaining on long hood roof behind cab EOT antenna stand on left side of cab roof All road numbers feature: Front ATSF-style relocated LED-illuminated headlight with lenses in low short hood; blanked number board light mount GP30 cab with increased length on left (fireman’s) side, cab heater vents deleted, and flat center windshield section Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-illuminated “hemisphere” walkway lights on hood ends, and at end of raised walkway duct* Blanked front and rear class lights with round plate LED-illuminated, printed and backlit cab number boards, and blanked long hood end number boards Vapor Corp. cab roof HVAC Front and rear multiple unit (MU) hose catch bars 3-hose multiple unit (MU) hose clusters with silver gladhands Semi-scale coupler buffer equipped with durable metal semi-scale Type E knuckle couplers Front and rear straight uncoupling levers with loop handles; two inner and two outer mounting brackets Modified pilot faces with uncoupling lever loop notches Deck-mounted multiple unit (MU) receptacle Dummy multiple unit (MU) receptacles with cable mounted to pilot face Handrail set with center gangway chains Front and rear standard drop steps Scale sectioned treadplate detail with EMD early “X” style pattern 81” GP30 low short hood with ratchet handbrake, chain guard, and square sand fill Hinged battery box doors with early hinges and narrow louvers Early cab sub-base doors with early hinges Detailed cab interior with separate floor, rear wall, seats, and standard AAR control stand Rectangular vent on left side of cab Sliding cab side windows Tall wind wings mounted fore of cab windows, left side, and small mirror on right side Standard EMD sunshades with long sunshade tracks Lost-wax brass cast Nathan AirChime K3LA horn mounted to right side cab roof eave. Large Sinclair Excalibur “ice skate” antenna (communications) mounted on a stand centered on the cab roof Accurate hood door and long hood detail Late single-panel inertial compartment with retrofitted latched and hinged access doors Wire inertial air intake grills Tall turbo exhaust stack Standard-range dynamic brakes with 48” fan Late See-through dynamic brake intake grills with horizontal wires through vertical vanes 7-horizontal rib radiator intake grills See-through front and rear 48” radiator fan housings with 8-blade fans; 36” pan-top center radiator fan Curved radiator fan grab iron Square sand fill hatch on top of long hood end Rear LED-illuminated horizontal headlight with lenses Underbody frame rail with separate plumbing Detailed Blomberg-B trucks with Hyatt bearing housings; elliptical springs; end transom detail; separate sanding lines and brackets; deleted outer brake shoes; and separate swing hanger detail Dimensionally accurate truck centers Aeroquip speed recorder on #2 axle, left side. Spare knuckle holders mounted to truck sideframes Frame-mounted bronze bell Prime air filter (can style) 2,600-gallon fuel tank sill skirt removed and relocated vertical gauges; round gauges in fuel tank sides; fuel fillers exposed Factory-applied wire grab irons, photoetched lift rings, windshield wipers, trainline hoses with silver gladhands, air tanks, sand hatch covers and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended radius: 22” DCC & sound equipped locomotives also feature: ESU LokSound 5 DCC & Sound decoder with “Full Throttle” Two (2) cube-type speakers Turbocharged 16-645D3A prime mover sound ESU designed “PowerPack” with two super capacitors*** Operates on both DC and DCC layouts DC/DCC & sound-ready locomotives also feature: Operable on DC layouts DCC-ready with 21-pin connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC ** Class lights illuminate in white color only in DC operation. Access and changing colors requires an ESU decoder with appropriate programming while operating using DCC ***“PowerPack” feature only compatible with appropriately programmed ESU decoders operating on a DCC layout

• mit DCC Motordekoder
• mit Sound

New paint scheme Era: Late 80s to Mid-90s Series ATSF 2746 to 2785 (rebuilt between 1982-1984) ATSF 2777 “Faded” ATSF Yellow w/ fresh paint touch-ups at various locations Mounting flanges from removed inertial air intake hoods remaining on long hood roof behind cab EOT antenna stand on right side of cab roof ATSF 2785 “Faded” ATSF Yellow w/ fresh paint touch-ups at various locations Mounting flanges from removed inertial air intake hoods remaining on long hood roof behind cab EOT antenna stand on left side of cab roof All road numbers feature: Front ATSF-style relocated LED-illuminated headlight with lenses in low short hood; blanked number board light mount GP30 cab with increased length on left (fireman’s) side, cab heater vents deleted, and flat center windshield section Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-illuminated “hemisphere” walkway lights on hood ends, and at end of raised walkway duct* Blanked front and rear class lights with round plate LED-illuminated, printed and backlit cab number boards, and blanked long hood end number boards Vapor Corp. cab roof HVAC Front and rear multiple unit (MU) hose catch bars 3-hose multiple unit (MU) hose clusters with silver gladhands Semi-scale coupler buffer equipped with durable metal semi-scale Type E knuckle couplers Front and rear straight uncoupling levers with loop handles; two inner and two outer mounting brackets Modified pilot faces with uncoupling lever loop notches Deck-mounted multiple unit (MU) receptacle Dummy multiple unit (MU) receptacles with cable mounted to pilot face Handrail set with center gangway chains Front and rear standard drop steps Scale sectioned treadplate detail with EMD early “X” style pattern 81” GP30 low short hood with ratchet handbrake, chain guard, and square sand fill Hinged battery box doors with early hinges and narrow louvers Early cab sub-base doors with early hinges Detailed cab interior with separate floor, rear wall, seats, and standard AAR control stand Rectangular vent on left side of cab Sliding cab side windows Tall wind wings mounted fore of cab windows, left side, and small mirror on right side Standard EMD sunshades with long sunshade tracks Lost-wax brass cast Nathan AirChime K3LA horn mounted to right side cab roof eave. Large Sinclair Excalibur “ice skate” antenna (communications) mounted on a stand centered on the cab roof Accurate hood door and long hood detail Late single-panel inertial compartment with retrofitted latched and hinged access doors Wire inertial air intake grills Tall turbo exhaust stack Standard-range dynamic brakes with 48” fan Late See-through dynamic brake intake grills with horizontal wires through vertical vanes 7-horizontal rib radiator intake grills See-through front and rear 48” radiator fan housings with 8-blade fans; 36” pan-top center radiator fan Curved radiator fan grab iron Square sand fill hatch on top of long hood end Rear LED-illuminated horizontal headlight with lenses Underbody frame rail with separate plumbing Detailed Blomberg-B trucks with Hyatt bearing housings; elliptical springs; end transom detail; separate sanding lines and brackets; deleted outer brake shoes; and separate swing hanger detail Dimensionally accurate truck centers Aeroquip speed recorder on #2 axle, left side. Spare knuckle holders mounted to truck sideframes Frame-mounted bronze bell Prime air filter (can style) 2,600-gallon fuel tank sill skirt removed and relocated vertical gauges; round gauges in fuel tank sides; fuel fillers exposed Factory-applied wire grab irons, photoetched lift rings, windshield wipers, trainline hoses with silver gladhands, air tanks, sand hatch covers and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended radius: 22” DCC & sound equipped locomotives also feature: ESU LokSound 5 DCC & Sound decoder with “Full Throttle” Two (2) cube-type speakers Turbocharged 16-645D3A prime mover sound ESU designed “PowerPack” with two super capacitors*** Operates on both DC and DCC layouts DC/DCC & sound-ready locomotives also feature: Operable on DC layouts DCC-ready with 21-pin connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC ** Class lights illuminate in white color only in DC operation. Access and changing colors requires an ESU decoder with appropriate programming while operating using DCC ***“PowerPack” feature only compatible with appropriately programmed ESU decoders operating on a DCC layout

• mit DCC Motordekoder
• mit Sound

New paint scheme Era: Late 80s to Mid-90s Series ATSF 2746 to 2785 (rebuilt between 1982-1984) ATSF 2777 “Faded” ATSF Yellow w/ fresh paint touch-ups at various locations Mounting flanges from removed inertial air intake hoods remaining on long hood roof behind cab EOT antenna stand on right side of cab roof ATSF 2785 “Faded” ATSF Yellow w/ fresh paint touch-ups at various locations Mounting flanges from removed inertial air intake hoods remaining on long hood roof behind cab EOT antenna stand on left side of cab roof All road numbers feature: Front ATSF-style relocated LED-illuminated headlight with lenses in low short hood; blanked number board light mount GP30 cab with increased length on left (fireman’s) side, cab heater vents deleted, and flat center windshield section Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-illuminated “hemisphere” walkway lights on hood ends, and at end of raised walkway duct* Blanked front and rear class lights with round plate LED-illuminated, printed and backlit cab number boards, and blanked long hood end number boards Vapor Corp. cab roof HVAC Front and rear multiple unit (MU) hose catch bars 3-hose multiple unit (MU) hose clusters with silver gladhands Semi-scale coupler buffer equipped with durable metal semi-scale Type E knuckle couplers Front and rear straight uncoupling levers with loop handles; two inner and two outer mounting brackets Modified pilot faces with uncoupling lever loop notches Deck-mounted multiple unit (MU) receptacle Dummy multiple unit (MU) receptacles with cable mounted to pilot face Handrail set with center gangway chains Front and rear standard drop steps Scale sectioned treadplate detail with EMD early “X” style pattern 81” GP30 low short hood with ratchet handbrake, chain guard, and square sand fill Hinged battery box doors with early hinges and narrow louvers Early cab sub-base doors with early hinges Detailed cab interior with separate floor, rear wall, seats, and standard AAR control stand Rectangular vent on left side of cab Sliding cab side windows Tall wind wings mounted fore of cab windows, left side, and small mirror on right side Standard EMD sunshades with long sunshade tracks Lost-wax brass cast Nathan AirChime K3LA horn mounted to right side cab roof eave. Large Sinclair Excalibur “ice skate” antenna (communications) mounted on a stand centered on the cab roof Accurate hood door and long hood detail Late single-panel inertial compartment with retrofitted latched and hinged access doors Wire inertial air intake grills Tall turbo exhaust stack Standard-range dynamic brakes with 48” fan Late See-through dynamic brake intake grills with horizontal wires through vertical vanes 7-horizontal rib radiator intake grills See-through front and rear 48” radiator fan housings with 8-blade fans; 36” pan-top center radiator fan Curved radiator fan grab iron Square sand fill hatch on top of long hood end Rear LED-illuminated horizontal headlight with lenses Underbody frame rail with separate plumbing Detailed Blomberg-B trucks with Hyatt bearing housings; elliptical springs; end transom detail; separate sanding lines and brackets; deleted outer brake shoes; and separate swing hanger detail Dimensionally accurate truck centers Aeroquip speed recorder on #2 axle, left side. Spare knuckle holders mounted to truck sideframes Frame-mounted bronze bell Prime air filter (can style) 2,600-gallon fuel tank sill skirt removed and relocated vertical gauges; round gauges in fuel tank sides; fuel fillers exposed Factory-applied wire grab irons, photoetched lift rings, windshield wipers, trainline hoses with silver gladhands, air tanks, sand hatch covers and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended radius: 22” DCC & sound equipped locomotives also feature: ESU LokSound 5 DCC & Sound decoder with “Full Throttle” Two (2) cube-type speakers Turbocharged 16-645D3A prime mover sound ESU designed “PowerPack” with two super capacitors*** Operates on both DC and DCC layouts DC/DCC & sound-ready locomotives also feature: Operable on DC layouts DCC-ready with 21-pin connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC ** Class lights illuminate in white color only in DC operation. Access and changing colors requires an ESU decoder with appropriate programming while operating using DCC ***“PowerPack” feature only compatible with appropriately programmed ESU decoders operating on a DCC layout

• DCC vorbereitet (Schnittstelle vorhanden)

New paint scheme Era: Late 80s to Mid-90s Series ATSF 2746 to 2785 (rebuilt between 1982-1984) ATSF 2777 “Faded” ATSF Yellow w/ fresh paint touch-ups at various locations Mounting flanges from removed inertial air intake hoods remaining on long hood roof behind cab EOT antenna stand on right side of cab roof ATSF 2785 “Faded” ATSF Yellow w/ fresh paint touch-ups at various locations Mounting flanges from removed inertial air intake hoods remaining on long hood roof behind cab EOT antenna stand on left side of cab roof All road numbers feature: Front ATSF-style relocated LED-illuminated headlight with lenses in low short hood; blanked number board light mount GP30 cab with increased length on left (fireman’s) side, cab heater vents deleted, and flat center windshield section Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-illuminated “hemisphere” walkway lights on hood ends, and at end of raised walkway duct* Blanked front and rear class lights with round plate LED-illuminated, printed and backlit cab number boards, and blanked long hood end number boards Vapor Corp. cab roof HVAC Front and rear multiple unit (MU) hose catch bars 3-hose multiple unit (MU) hose clusters with silver gladhands Semi-scale coupler buffer equipped with durable metal semi-scale Type E knuckle couplers Front and rear straight uncoupling levers with loop handles; two inner and two outer mounting brackets Modified pilot faces with uncoupling lever loop notches Deck-mounted multiple unit (MU) receptacle Dummy multiple unit (MU) receptacles with cable mounted to pilot face Handrail set with center gangway chains Front and rear standard drop steps Scale sectioned treadplate detail with EMD early “X” style pattern 81” GP30 low short hood with ratchet handbrake, chain guard, and square sand fill Hinged battery box doors with early hinges and narrow louvers Early cab sub-base doors with early hinges Detailed cab interior with separate floor, rear wall, seats, and standard AAR control stand Rectangular vent on left side of cab Sliding cab side windows Tall wind wings mounted fore of cab windows, left side, and small mirror on right side Standard EMD sunshades with long sunshade tracks Lost-wax brass cast Nathan AirChime K3LA horn mounted to right side cab roof eave. Large Sinclair Excalibur “ice skate” antenna (communications) mounted on a stand centered on the cab roof Accurate hood door and long hood detail Late single-panel inertial compartment with retrofitted latched and hinged access doors Wire inertial air intake grills Tall turbo exhaust stack Standard-range dynamic brakes with 48” fan Late See-through dynamic brake intake grills with horizontal wires through vertical vanes 7-horizontal rib radiator intake grills See-through front and rear 48” radiator fan housings with 8-blade fans; 36” pan-top center radiator fan Curved radiator fan grab iron Square sand fill hatch on top of long hood end Rear LED-illuminated horizontal headlight with lenses Underbody frame rail with separate plumbing Detailed Blomberg-B trucks with Hyatt bearing housings; elliptical springs; end transom detail; separate sanding lines and brackets; deleted outer brake shoes; and separate swing hanger detail Dimensionally accurate truck centers Aeroquip speed recorder on #2 axle, left side. Spare knuckle holders mounted to truck sideframes Frame-mounted bronze bell Prime air filter (can style) 2,600-gallon fuel tank sill skirt removed and relocated vertical gauges; round gauges in fuel tank sides; fuel fillers exposed Factory-applied wire grab irons, photoetched lift rings, windshield wipers, trainline hoses with silver gladhands, air tanks, sand hatch covers and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended radius: 22” DCC & sound equipped locomotives also feature: ESU LokSound 5 DCC & Sound decoder with “Full Throttle” Two (2) cube-type speakers Turbocharged 16-645D3A prime mover sound ESU designed “PowerPack” with two super capacitors*** Operates on both DC and DCC layouts DC/DCC & sound-ready locomotives also feature: Operable on DC layouts DCC-ready with 21-pin connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC ** Class lights illuminate in white color only in DC operation. Access and changing colors requires an ESU decoder with appropriate programming while operating using DCC ***“PowerPack” feature only compatible with appropriately programmed ESU decoders operating on a DCC layout

• mit DCC Motordekoder
• mit Sound

New paint scheme Era: Late 80s to Mid-90s Series ATSF 2746 to 2785 (rebuilt between 1982-1984) ATSF 2777 “Faded” ATSF Yellow w/ fresh paint touch-ups at various locations Mounting flanges from removed inertial air intake hoods remaining on long hood roof behind cab EOT antenna stand on right side of cab roof ATSF 2785 “Faded” ATSF Yellow w/ fresh paint touch-ups at various locations Mounting flanges from removed inertial air intake hoods remaining on long hood roof behind cab EOT antenna stand on left side of cab roof All road numbers feature: Front ATSF-style relocated LED-illuminated headlight with lenses in low short hood; blanked number board light mount GP30 cab with increased length on left (fireman’s) side, cab heater vents deleted, and flat center windshield section Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-illuminated “hemisphere” walkway lights on hood ends, and at end of raised walkway duct* Blanked front and rear class lights with round plate LED-illuminated, printed and backlit cab number boards, and blanked long hood end number boards Vapor Corp. cab roof HVAC Front and rear multiple unit (MU) hose catch bars 3-hose multiple unit (MU) hose clusters with silver gladhands Semi-scale coupler buffer equipped with durable metal semi-scale Type E knuckle couplers Front and rear straight uncoupling levers with loop handles; two inner and two outer mounting brackets Modified pilot faces with uncoupling lever loop notches Deck-mounted multiple unit (MU) receptacle Dummy multiple unit (MU) receptacles with cable mounted to pilot face Handrail set with center gangway chains Front and rear standard drop steps Scale sectioned treadplate detail with EMD early “X” style pattern 81” GP30 low short hood with ratchet handbrake, chain guard, and square sand fill Hinged battery box doors with early hinges and narrow louvers Early cab sub-base doors with early hinges Detailed cab interior with separate floor, rear wall, seats, and standard AAR control stand Rectangular vent on left side of cab Sliding cab side windows Tall wind wings mounted fore of cab windows, left side, and small mirror on right side Standard EMD sunshades with long sunshade tracks Lost-wax brass cast Nathan AirChime K3LA horn mounted to right side cab roof eave. Large Sinclair Excalibur “ice skate” antenna (communications) mounted on a stand centered on the cab roof Accurate hood door and long hood detail Late single-panel inertial compartment with retrofitted latched and hinged access doors Wire inertial air intake grills Tall turbo exhaust stack Standard-range dynamic brakes with 48” fan Late See-through dynamic brake intake grills with horizontal wires through vertical vanes 7-horizontal rib radiator intake grills See-through front and rear 48” radiator fan housings with 8-blade fans; 36” pan-top center radiator fan Curved radiator fan grab iron Square sand fill hatch on top of long hood end Rear LED-illuminated horizontal headlight with lenses Underbody frame rail with separate plumbing Detailed Blomberg-B trucks with Hyatt bearing housings; elliptical springs; end transom detail; separate sanding lines and brackets; deleted outer brake shoes; and separate swing hanger detail Dimensionally accurate truck centers Aeroquip speed recorder on #2 axle, left side. Spare knuckle holders mounted to truck sideframes Frame-mounted bronze bell Prime air filter (can style) 2,600-gallon fuel tank sill skirt removed and relocated vertical gauges; round gauges in fuel tank sides; fuel fillers exposed Factory-applied wire grab irons, photoetched lift rings, windshield wipers, trainline hoses with silver gladhands, air tanks, sand hatch covers and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended radius: 22” DCC & sound equipped locomotives also feature: ESU LokSound 5 DCC & Sound decoder with “Full Throttle” Two (2) cube-type speakers Turbocharged 16-645D3A prime mover sound ESU designed “PowerPack” with two super capacitors*** Operates on both DC and DCC layouts DC/DCC & sound-ready locomotives also feature: Operable on DC layouts DCC-ready with 21-pin connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC ** Class lights illuminate in white color only in DC operation. Access and changing colors requires an ESU decoder with appropriate programming while operating using DCC ***“PowerPack” feature only compatible with appropriately programmed ESU decoders operating on a DCC layout

• mit DCC Motordekoder
• mit Sound

New paint scheme Era: Late 80s to Mid-90s Series ATSF 2746 to 2785 (rebuilt between 1982-1984) ATSF 2777 “Faded” ATSF Yellow w/ fresh paint touch-ups at various locations Mounting flanges from removed inertial air intake hoods remaining on long hood roof behind cab EOT antenna stand on right side of cab roof ATSF 2785 “Faded” ATSF Yellow w/ fresh paint touch-ups at various locations Mounting flanges from removed inertial air intake hoods remaining on long hood roof behind cab EOT antenna stand on left side of cab roof All road numbers feature: Front ATSF-style relocated LED-illuminated headlight with lenses in low short hood; blanked number board light mount GP30 cab with increased length on left (fireman’s) side, cab heater vents deleted, and flat center windshield section Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-illuminated “hemisphere” walkway lights on hood ends, and at end of raised walkway duct* Blanked front and rear class lights with round plate LED-illuminated, printed and backlit cab number boards, and blanked long hood end number boards Vapor Corp. cab roof HVAC Front and rear multiple unit (MU) hose catch bars 3-hose multiple unit (MU) hose clusters with silver gladhands Semi-scale coupler buffer equipped with durable metal semi-scale Type E knuckle couplers Front and rear straight uncoupling levers with loop handles; two inner and two outer mounting brackets Modified pilot faces with uncoupling lever loop notches Deck-mounted multiple unit (MU) receptacle Dummy multiple unit (MU) receptacles with cable mounted to pilot face Handrail set with center gangway chains Front and rear standard drop steps Scale sectioned treadplate detail with EMD early “X” style pattern 81” GP30 low short hood with ratchet handbrake, chain guard, and square sand fill Hinged battery box doors with early hinges and narrow louvers Early cab sub-base doors with early hinges Detailed cab interior with separate floor, rear wall, seats, and standard AAR control stand Rectangular vent on left side of cab Sliding cab side windows Tall wind wings mounted fore of cab windows, left side, and small mirror on right side Standard EMD sunshades with long sunshade tracks Lost-wax brass cast Nathan AirChime K3LA horn mounted to right side cab roof eave. Large Sinclair Excalibur “ice skate” antenna (communications) mounted on a stand centered on the cab roof Accurate hood door and long hood detail Late single-panel inertial compartment with retrofitted latched and hinged access doors Wire inertial air intake grills Tall turbo exhaust stack Standard-range dynamic brakes with 48” fan Late See-through dynamic brake intake grills with horizontal wires through vertical vanes 7-horizontal rib radiator intake grills See-through front and rear 48” radiator fan housings with 8-blade fans; 36” pan-top center radiator fan Curved radiator fan grab iron Square sand fill hatch on top of long hood end Rear LED-illuminated horizontal headlight with lenses Underbody frame rail with separate plumbing Detailed Blomberg-B trucks with Hyatt bearing housings; elliptical springs; end transom detail; separate sanding lines and brackets; deleted outer brake shoes; and separate swing hanger detail Dimensionally accurate truck centers Aeroquip speed recorder on #2 axle, left side. Spare knuckle holders mounted to truck sideframes Frame-mounted bronze bell Prime air filter (can style) 2,600-gallon fuel tank sill skirt removed and relocated vertical gauges; round gauges in fuel tank sides; fuel fillers exposed Factory-applied wire grab irons, photoetched lift rings, windshield wipers, trainline hoses with silver gladhands, air tanks, sand hatch covers and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended radius: 22” DCC & sound equipped locomotives also feature: ESU LokSound 5 DCC & Sound decoder with “Full Throttle” Two (2) cube-type speakers Turbocharged 16-645D3A prime mover sound ESU designed “PowerPack” with two super capacitors*** Operates on both DC and DCC layouts DC/DCC & sound-ready locomotives also feature: Operable on DC layouts DCC-ready with 21-pin connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC ** Class lights illuminate in white color only in DC operation. Access and changing colors requires an ESU decoder with appropriate programming while operating using DCC ***“PowerPack” feature only compatible with appropriately programmed ESU decoders operating on a DCC layout

• DCC vorbereitet (Schnittstelle vorhanden)

New paint scheme Era: Late 80s to Mid-90s Series ATSF 2746 to 2785 (rebuilt between 1982-1984) ATSF 2777 “Faded” ATSF Yellow w/ fresh paint touch-ups at various locations Mounting flanges from removed inertial air intake hoods remaining on long hood roof behind cab EOT antenna stand on right side of cab roof ATSF 2785 “Faded” ATSF Yellow w/ fresh paint touch-ups at various locations Mounting flanges from removed inertial air intake hoods remaining on long hood roof behind cab EOT antenna stand on left side of cab roof All road numbers feature: Front ATSF-style relocated LED-illuminated headlight with lenses in low short hood; blanked number board light mount GP30 cab with increased length on left (fireman’s) side, cab heater vents deleted, and flat center windshield section Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-illuminated “hemisphere” walkway lights on hood ends, and at end of raised walkway duct* Blanked front and rear class lights with round plate LED-illuminated, printed and backlit cab number boards, and blanked long hood end number boards Vapor Corp. cab roof HVAC Front and rear multiple unit (MU) hose catch bars 3-hose multiple unit (MU) hose clusters with silver gladhands Semi-scale coupler buffer equipped with durable metal semi-scale Type E knuckle couplers Front and rear straight uncoupling levers with loop handles; two inner and two outer mounting brackets Modified pilot faces with uncoupling lever loop notches Deck-mounted multiple unit (MU) receptacle Dummy multiple unit (MU) receptacles with cable mounted to pilot face Handrail set with center gangway chains Front and rear standard drop steps Scale sectioned treadplate detail with EMD early “X” style pattern 81” GP30 low short hood with ratchet handbrake, chain guard, and square sand fill Hinged battery box doors with early hinges and narrow louvers Early cab sub-base doors with early hinges Detailed cab interior with separate floor, rear wall, seats, and standard AAR control stand Rectangular vent on left side of cab Sliding cab side windows Tall wind wings mounted fore of cab windows, left side, and small mirror on right side Standard EMD sunshades with long sunshade tracks Lost-wax brass cast Nathan AirChime K3LA horn mounted to right side cab roof eave. Large Sinclair Excalibur “ice skate” antenna (communications) mounted on a stand centered on the cab roof Accurate hood door and long hood detail Late single-panel inertial compartment with retrofitted latched and hinged access doors Wire inertial air intake grills Tall turbo exhaust stack Standard-range dynamic brakes with 48” fan Late See-through dynamic brake intake grills with horizontal wires through vertical vanes 7-horizontal rib radiator intake grills See-through front and rear 48” radiator fan housings with 8-blade fans; 36” pan-top center radiator fan Curved radiator fan grab iron Square sand fill hatch on top of long hood end Rear LED-illuminated horizontal headlight with lenses Underbody frame rail with separate plumbing Detailed Blomberg-B trucks with Hyatt bearing housings; elliptical springs; end transom detail; separate sanding lines and brackets; deleted outer brake shoes; and separate swing hanger detail Dimensionally accurate truck centers Aeroquip speed recorder on #2 axle, left side. Spare knuckle holders mounted to truck sideframes Frame-mounted bronze bell Prime air filter (can style) 2,600-gallon fuel tank sill skirt removed and relocated vertical gauges; round gauges in fuel tank sides; fuel fillers exposed Factory-applied wire grab irons, photoetched lift rings, windshield wipers, trainline hoses with silver gladhands, air tanks, sand hatch covers and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended radius: 22” DCC & sound equipped locomotives also feature: ESU LokSound 5 DCC & Sound decoder with “Full Throttle” Two (2) cube-type speakers Turbocharged 16-645D3A prime mover sound ESU designed “PowerPack” with two super capacitors*** Operates on both DC and DCC layouts DC/DCC & sound-ready locomotives also feature: Operable on DC layouts DCC-ready with 21-pin connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC ** Class lights illuminate in white color only in DC operation. Access and changing colors requires an ESU decoder with appropriate programming while operating using DCC ***“PowerPack” feature only compatible with appropriately programmed ESU decoders operating on a DCC layout

• mit DCC Motordekoder
• mit Sound

New paint scheme Era: Late 80s to Mid-90s Series ATSF 2746 to 2785 (rebuilt between 1982-1984) ATSF 2777 “Faded” ATSF Yellow w/ fresh paint touch-ups at various locations Mounting flanges from removed inertial air intake hoods remaining on long hood roof behind cab EOT antenna stand on right side of cab roof ATSF 2785 “Faded” ATSF Yellow w/ fresh paint touch-ups at various locations Mounting flanges from removed inertial air intake hoods remaining on long hood roof behind cab EOT antenna stand on left side of cab roof All road numbers feature: Front ATSF-style relocated LED-illuminated headlight with lenses in low short hood; blanked number board light mount GP30 cab with increased length on left (fireman’s) side, cab heater vents deleted, and flat center windshield section Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-illuminated “hemisphere” walkway lights on hood ends, and at end of raised walkway duct* Blanked front and rear class lights with round plate LED-illuminated, printed and backlit cab number boards, and blanked long hood end number boards Vapor Corp. cab roof HVAC Front and rear multiple unit (MU) hose catch bars 3-hose multiple unit (MU) hose clusters with silver gladhands Semi-scale coupler buffer equipped with durable metal semi-scale Type E knuckle couplers Front and rear straight uncoupling levers with loop handles; two inner and two outer mounting brackets Modified pilot faces with uncoupling lever loop notches Deck-mounted multiple unit (MU) receptacle Dummy multiple unit (MU) receptacles with cable mounted to pilot face Handrail set with center gangway chains Front and rear standard drop steps Scale sectioned treadplate detail with EMD early “X” style pattern 81” GP30 low short hood with ratchet handbrake, chain guard, and square sand fill Hinged battery box doors with early hinges and narrow louvers Early cab sub-base doors with early hinges Detailed cab interior with separate floor, rear wall, seats, and standard AAR control stand Rectangular vent on left side of cab Sliding cab side windows Tall wind wings mounted fore of cab windows, left side, and small mirror on right side Standard EMD sunshades with long sunshade tracks Lost-wax brass cast Nathan AirChime K3LA horn mounted to right side cab roof eave. Large Sinclair Excalibur “ice skate” antenna (communications) mounted on a stand centered on the cab roof Accurate hood door and long hood detail Late single-panel inertial compartment with retrofitted latched and hinged access doors Wire inertial air intake grills Tall turbo exhaust stack Standard-range dynamic brakes with 48” fan Late See-through dynamic brake intake grills with horizontal wires through vertical vanes 7-horizontal rib radiator intake grills See-through front and rear 48” radiator fan housings with 8-blade fans; 36” pan-top center radiator fan Curved radiator fan grab iron Square sand fill hatch on top of long hood end Rear LED-illuminated horizontal headlight with lenses Underbody frame rail with separate plumbing Detailed Blomberg-B trucks with Hyatt bearing housings; elliptical springs; end transom detail; separate sanding lines and brackets; deleted outer brake shoes; and separate swing hanger detail Dimensionally accurate truck centers Aeroquip speed recorder on #2 axle, left side. Spare knuckle holders mounted to truck sideframes Frame-mounted bronze bell Prime air filter (can style) 2,600-gallon fuel tank sill skirt removed and relocated vertical gauges; round gauges in fuel tank sides; fuel fillers exposed Factory-applied wire grab irons, photoetched lift rings, windshield wipers, trainline hoses with silver gladhands, air tanks, sand hatch covers and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended radius: 22” DCC & sound equipped locomotives also feature: ESU LokSound 5 DCC & Sound decoder with “Full Throttle” Two (2) cube-type speakers Turbocharged 16-645D3A prime mover sound ESU designed “PowerPack” with two super capacitors*** Operates on both DC and DCC layouts DC/DCC & sound-ready locomotives also feature: Operable on DC layouts DCC-ready with 21-pin connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC ** Class lights illuminate in white color only in DC operation. Access and changing colors requires an ESU decoder with appropriate programming while operating using DCC ***“PowerPack” feature only compatible with appropriately programmed ESU decoders operating on a DCC layout

• DCC vorbereitet (Schnittstelle vorhanden)

New paint scheme Era: Late 80s to Mid-90s Series ATSF 2746 to 2785 (rebuilt between 1982-1984) ATSF 2777 “Faded” ATSF Yellow w/ fresh paint touch-ups at various locations Mounting flanges from removed inertial air intake hoods remaining on long hood roof behind cab EOT antenna stand on right side of cab roof ATSF 2785 “Faded” ATSF Yellow w/ fresh paint touch-ups at various locations Mounting flanges from removed inertial air intake hoods remaining on long hood roof behind cab EOT antenna stand on left side of cab roof All road numbers feature: Front ATSF-style relocated LED-illuminated headlight with lenses in low short hood; blanked number board light mount GP30 cab with increased length on left (fireman’s) side, cab heater vents deleted, and flat center windshield section Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-illuminated “hemisphere” walkway lights on hood ends, and at end of raised walkway duct* Blanked front and rear class lights with round plate LED-illuminated, printed and backlit cab number boards, and blanked long hood end number boards Vapor Corp. cab roof HVAC Front and rear multiple unit (MU) hose catch bars 3-hose multiple unit (MU) hose clusters with silver gladhands Semi-scale coupler buffer equipped with durable metal semi-scale Type E knuckle couplers Front and rear straight uncoupling levers with loop handles; two inner and two outer mounting brackets Modified pilot faces with uncoupling lever loop notches Deck-mounted multiple unit (MU) receptacle Dummy multiple unit (MU) receptacles with cable mounted to pilot face Handrail set with center gangway chains Front and rear standard drop steps Scale sectioned treadplate detail with EMD early “X” style pattern 81” GP30 low short hood with ratchet handbrake, chain guard, and square sand fill Hinged battery box doors with early hinges and narrow louvers Early cab sub-base doors with early hinges Detailed cab interior with separate floor, rear wall, seats, and standard AAR control stand Rectangular vent on left side of cab Sliding cab side windows Tall wind wings mounted fore of cab windows, left side, and small mirror on right side Standard EMD sunshades with long sunshade tracks Lost-wax brass cast Nathan AirChime K3LA horn mounted to right side cab roof eave. Large Sinclair Excalibur “ice skate” antenna (communications) mounted on a stand centered on the cab roof Accurate hood door and long hood detail Late single-panel inertial compartment with retrofitted latched and hinged access doors Wire inertial air intake grills Tall turbo exhaust stack Standard-range dynamic brakes with 48” fan Late See-through dynamic brake intake grills with horizontal wires through vertical vanes 7-horizontal rib radiator intake grills See-through front and rear 48” radiator fan housings with 8-blade fans; 36” pan-top center radiator fan Curved radiator fan grab iron Square sand fill hatch on top of long hood end Rear LED-illuminated horizontal headlight with lenses Underbody frame rail with separate plumbing Detailed Blomberg-B trucks with Hyatt bearing housings; elliptical springs; end transom detail; separate sanding lines and brackets; deleted outer brake shoes; and separate swing hanger detail Dimensionally accurate truck centers Aeroquip speed recorder on #2 axle, left side. Spare knuckle holders mounted to truck sideframes Frame-mounted bronze bell Prime air filter (can style) 2,600-gallon fuel tank sill skirt removed and relocated vertical gauges; round gauges in fuel tank sides; fuel fillers exposed Factory-applied wire grab irons, photoetched lift rings, windshield wipers, trainline hoses with silver gladhands, air tanks, sand hatch covers and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended radius: 22” DCC & sound equipped locomotives also feature: ESU LokSound 5 DCC & Sound decoder with “Full Throttle” Two (2) cube-type speakers Turbocharged 16-645D3A prime mover sound ESU designed “PowerPack” with two super capacitors*** Operates on both DC and DCC layouts DC/DCC & sound-ready locomotives also feature: Operable on DC layouts DCC-ready with 21-pin connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC ** Class lights illuminate in white color only in DC operation. Access and changing colors requires an ESU decoder with appropriate programming while operating using DCC ***“PowerPack” feature only compatible with appropriately programmed ESU decoders operating on a DCC layout

• mit DCC Motordekoder
• mit Sound

New paint scheme Era: Late 80s to Mid-90s Series ATSF 2746 to 2785 (rebuilt between 1982-1984) ATSF 2777 “Faded” ATSF Yellow w/ fresh paint touch-ups at various locations Mounting flanges from removed inertial air intake hoods remaining on long hood roof behind cab EOT antenna stand on right side of cab roof ATSF 2785 “Faded” ATSF Yellow w/ fresh paint touch-ups at various locations Mounting flanges from removed inertial air intake hoods remaining on long hood roof behind cab EOT antenna stand on left side of cab roof All road numbers feature: Front ATSF-style relocated LED-illuminated headlight with lenses in low short hood; blanked number board light mount GP30 cab with increased length on left (fireman’s) side, cab heater vents deleted, and flat center windshield section Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-illuminated “hemisphere” walkway lights on hood ends, and at end of raised walkway duct* Blanked front and rear class lights with round plate LED-illuminated, printed and backlit cab number boards, and blanked long hood end number boards Vapor Corp. cab roof HVAC Front and rear multiple unit (MU) hose catch bars 3-hose multiple unit (MU) hose clusters with silver gladhands Semi-scale coupler buffer equipped with durable metal semi-scale Type E knuckle couplers Front and rear straight uncoupling levers with loop handles; two inner and two outer mounting brackets Modified pilot faces with uncoupling lever loop notches Deck-mounted multiple unit (MU) receptacle Dummy multiple unit (MU) receptacles with cable mounted to pilot face Handrail set with center gangway chains Front and rear standard drop steps Scale sectioned treadplate detail with EMD early “X” style pattern 81” GP30 low short hood with ratchet handbrake, chain guard, and square sand fill Hinged battery box doors with early hinges and narrow louvers Early cab sub-base doors with early hinges Detailed cab interior with separate floor, rear wall, seats, and standard AAR control stand Rectangular vent on left side of cab Sliding cab side windows Tall wind wings mounted fore of cab windows, left side, and small mirror on right side Standard EMD sunshades with long sunshade tracks Lost-wax brass cast Nathan AirChime K3LA horn mounted to right side cab roof eave. Large Sinclair Excalibur “ice skate” antenna (communications) mounted on a stand centered on the cab roof Accurate hood door and long hood detail Late single-panel inertial compartment with retrofitted latched and hinged access doors Wire inertial air intake grills Tall turbo exhaust stack Standard-range dynamic brakes with 48” fan Late See-through dynamic brake intake grills with horizontal wires through vertical vanes 7-horizontal rib radiator intake grills See-through front and rear 48” radiator fan housings with 8-blade fans; 36” pan-top center radiator fan Curved radiator fan grab iron Square sand fill hatch on top of long hood end Rear LED-illuminated horizontal headlight with lenses Underbody frame rail with separate plumbing Detailed Blomberg-B trucks with Hyatt bearing housings; elliptical springs; end transom detail; separate sanding lines and brackets; deleted outer brake shoes; and separate swing hanger detail Dimensionally accurate truck centers Aeroquip speed recorder on #2 axle, left side. Spare knuckle holders mounted to truck sideframes Frame-mounted bronze bell Prime air filter (can style) 2,600-gallon fuel tank sill skirt removed and relocated vertical gauges; round gauges in fuel tank sides; fuel fillers exposed Factory-applied wire grab irons, photoetched lift rings, windshield wipers, trainline hoses with silver gladhands, air tanks, sand hatch covers and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended radius: 22” DCC & sound equipped locomotives also feature: ESU LokSound 5 DCC & Sound decoder with “Full Throttle” Two (2) cube-type speakers Turbocharged 16-645D3A prime mover sound ESU designed “PowerPack” with two super capacitors*** Operates on both DC and DCC layouts DC/DCC & sound-ready locomotives also feature: Operable on DC layouts DCC-ready with 21-pin connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC ** Class lights illuminate in white color only in DC operation. Access and changing colors requires an ESU decoder with appropriate programming while operating using DCC ***“PowerPack” feature only compatible with appropriately programmed ESU decoders operating on a DCC layout

• DCC vorbereitet (Schnittstelle vorhanden)

New paint scheme Era: Late 80s to Mid-90s Series ATSF 2746 to 2785 (rebuilt between 1982-1984) ATSF 2777 “Faded” ATSF Yellow w/ fresh paint touch-ups at various locations Mounting flanges from removed inertial air intake hoods remaining on long hood roof behind cab EOT antenna stand on right side of cab roof ATSF 2785 “Faded” ATSF Yellow w/ fresh paint touch-ups at various locations Mounting flanges from removed inertial air intake hoods remaining on long hood roof behind cab EOT antenna stand on left side of cab roof All road numbers feature: Front ATSF-style relocated LED-illuminated headlight with lenses in low short hood; blanked number board light mount GP30 cab with increased length on left (fireman’s) side, cab heater vents deleted, and flat center windshield section Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-illuminated “hemisphere” walkway lights on hood ends, and at end of raised walkway duct* Blanked front and rear class lights with round plate LED-illuminated, printed and backlit cab number boards, and blanked long hood end number boards Vapor Corp. cab roof HVAC Front and rear multiple unit (MU) hose catch bars 3-hose multiple unit (MU) hose clusters with silver gladhands Semi-scale coupler buffer equipped with durable metal semi-scale Type E knuckle couplers Front and rear straight uncoupling levers with loop handles; two inner and two outer mounting brackets Modified pilot faces with uncoupling lever loop notches Deck-mounted multiple unit (MU) receptacle Dummy multiple unit (MU) receptacles with cable mounted to pilot face Handrail set with center gangway chains Front and rear standard drop steps Scale sectioned treadplate detail with EMD early “X” style pattern 81” GP30 low short hood with ratchet handbrake, chain guard, and square sand fill Hinged battery box doors with early hinges and narrow louvers Early cab sub-base doors with early hinges Detailed cab interior with separate floor, rear wall, seats, and standard AAR control stand Rectangular vent on left side of cab Sliding cab side windows Tall wind wings mounted fore of cab windows, left side, and small mirror on right side Standard EMD sunshades with long sunshade tracks Lost-wax brass cast Nathan AirChime K3LA horn mounted to right side cab roof eave. Large Sinclair Excalibur “ice skate” antenna (communications) mounted on a stand centered on the cab roof Accurate hood door and long hood detail Late single-panel inertial compartment with retrofitted latched and hinged access doors Wire inertial air intake grills Tall turbo exhaust stack Standard-range dynamic brakes with 48” fan Late See-through dynamic brake intake grills with horizontal wires through vertical vanes 7-horizontal rib radiator intake grills See-through front and rear 48” radiator fan housings with 8-blade fans; 36” pan-top center radiator fan Curved radiator fan grab iron Square sand fill hatch on top of long hood end Rear LED-illuminated horizontal headlight with lenses Underbody frame rail with separate plumbing Detailed Blomberg-B trucks with Hyatt bearing housings; elliptical springs; end transom detail; separate sanding lines and brackets; deleted outer brake shoes; and separate swing hanger detail Dimensionally accurate truck centers Aeroquip speed recorder on #2 axle, left side. Spare knuckle holders mounted to truck sideframes Frame-mounted bronze bell Prime air filter (can style) 2,600-gallon fuel tank sill skirt removed and relocated vertical gauges; round gauges in fuel tank sides; fuel fillers exposed Factory-applied wire grab irons, photoetched lift rings, windshield wipers, trainline hoses with silver gladhands, air tanks, sand hatch covers and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended radius: 22” DCC & sound equipped locomotives also feature: ESU LokSound 5 DCC & Sound decoder with “Full Throttle” Two (2) cube-type speakers Turbocharged 16-645D3A prime mover sound ESU designed “PowerPack” with two super capacitors*** Operates on both DC and DCC layouts DC/DCC & sound-ready locomotives also feature: Operable on DC layouts DCC-ready with 21-pin connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC ** Class lights illuminate in white color only in DC operation. Access and changing colors requires an ESU decoder with appropriate programming while operating using DCC ***“PowerPack” feature only compatible with appropriately programmed ESU decoders operating on a DCC layout

• mit DCC Motordekoder
• mit Sound

New paint scheme Era: Late 80s to Mid-90s Series ATSF 2746 to 2785 (rebuilt between 1982-1984) ATSF 2777 “Faded” ATSF Yellow w/ fresh paint touch-ups at various locations Mounting flanges from removed inertial air intake hoods remaining on long hood roof behind cab EOT antenna stand on right side of cab roof ATSF 2785 “Faded” ATSF Yellow w/ fresh paint touch-ups at various locations Mounting flanges from removed inertial air intake hoods remaining on long hood roof behind cab EOT antenna stand on left side of cab roof All road numbers feature: Front ATSF-style relocated LED-illuminated headlight with lenses in low short hood; blanked number board light mount GP30 cab with increased length on left (fireman’s) side, cab heater vents deleted, and flat center windshield section Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-illuminated “hemisphere” walkway lights on hood ends, and at end of raised walkway duct* Blanked front and rear class lights with round plate LED-illuminated, printed and backlit cab number boards, and blanked long hood end number boards Vapor Corp. cab roof HVAC Front and rear multiple unit (MU) hose catch bars 3-hose multiple unit (MU) hose clusters with silver gladhands Semi-scale coupler buffer equipped with durable metal semi-scale Type E knuckle couplers Front and rear straight uncoupling levers with loop handles; two inner and two outer mounting brackets Modified pilot faces with uncoupling lever loop notches Deck-mounted multiple unit (MU) receptacle Dummy multiple unit (MU) receptacles with cable mounted to pilot face Handrail set with center gangway chains Front and rear standard drop steps Scale sectioned treadplate detail with EMD early “X” style pattern 81” GP30 low short hood with ratchet handbrake, chain guard, and square sand fill Hinged battery box doors with early hinges and narrow louvers Early cab sub-base doors with early hinges Detailed cab interior with separate floor, rear wall, seats, and standard AAR control stand Rectangular vent on left side of cab Sliding cab side windows Tall wind wings mounted fore of cab windows, left side, and small mirror on right side Standard EMD sunshades with long sunshade tracks Lost-wax brass cast Nathan AirChime K3LA horn mounted to right side cab roof eave. Large Sinclair Excalibur “ice skate” antenna (communications) mounted on a stand centered on the cab roof Accurate hood door and long hood detail Late single-panel inertial compartment with retrofitted latched and hinged access doors Wire inertial air intake grills Tall turbo exhaust stack Standard-range dynamic brakes with 48” fan Late See-through dynamic brake intake grills with horizontal wires through vertical vanes 7-horizontal rib radiator intake grills See-through front and rear 48” radiator fan housings with 8-blade fans; 36” pan-top center radiator fan Curved radiator fan grab iron Square sand fill hatch on top of long hood end Rear LED-illuminated horizontal headlight with lenses Underbody frame rail with separate plumbing Detailed Blomberg-B trucks with Hyatt bearing housings; elliptical springs; end transom detail; separate sanding lines and brackets; deleted outer brake shoes; and separate swing hanger detail Dimensionally accurate truck centers Aeroquip speed recorder on #2 axle, left side. Spare knuckle holders mounted to truck sideframes Frame-mounted bronze bell Prime air filter (can style) 2,600-gallon fuel tank sill skirt removed and relocated vertical gauges; round gauges in fuel tank sides; fuel fillers exposed Factory-applied wire grab irons, photoetched lift rings, windshield wipers, trainline hoses with silver gladhands, air tanks, sand hatch covers and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended radius: 22” DCC & sound equipped locomotives also feature: ESU LokSound 5 DCC & Sound decoder with “Full Throttle” Two (2) cube-type speakers Turbocharged 16-645D3A prime mover sound ESU designed “PowerPack” with two super capacitors*** Operates on both DC and DCC layouts DC/DCC & sound-ready locomotives also feature: Operable on DC layouts DCC-ready with 21-pin connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC ** Class lights illuminate in white color only in DC operation. Access and changing colors requires an ESU decoder with appropriate programming while operating using DCC ***“PowerPack” feature only compatible with appropriately programmed ESU decoders operating on a DCC layout

• DCC vorbereitet (Schnittstelle vorhanden)

New paint scheme Era: Late 80s to Mid-90s Series ATSF 2746 to 2785 (rebuilt between 1982-1984) ATSF 2777 “Faded” ATSF Yellow w/ fresh paint touch-ups at various locations Mounting flanges from removed inertial air intake hoods remaining on long hood roof behind cab EOT antenna stand on right side of cab roof ATSF 2785 “Faded” ATSF Yellow w/ fresh paint touch-ups at various locations Mounting flanges from removed inertial air intake hoods remaining on long hood roof behind cab EOT antenna stand on left side of cab roof All road numbers feature: Front ATSF-style relocated LED-illuminated headlight with lenses in low short hood; blanked number board light mount GP30 cab with increased length on left (fireman’s) side, cab heater vents deleted, and flat center windshield section Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-illuminated “hemisphere” walkway lights on hood ends, and at end of raised walkway duct* Blanked front and rear class lights with round plate LED-illuminated, printed and backlit cab number boards, and blanked long hood end number boards Vapor Corp. cab roof HVAC Front and rear multiple unit (MU) hose catch bars 3-hose multiple unit (MU) hose clusters with silver gladhands Semi-scale coupler buffer equipped with durable metal semi-scale Type E knuckle couplers Front and rear straight uncoupling levers with loop handles; two inner and two outer mounting brackets Modified pilot faces with uncoupling lever loop notches Deck-mounted multiple unit (MU) receptacle Dummy multiple unit (MU) receptacles with cable mounted to pilot face Handrail set with center gangway chains Front and rear standard drop steps Scale sectioned treadplate detail with EMD early “X” style pattern 81” GP30 low short hood with ratchet handbrake, chain guard, and square sand fill Hinged battery box doors with early hinges and narrow louvers Early cab sub-base doors with early hinges Detailed cab interior with separate floor, rear wall, seats, and standard AAR control stand Rectangular vent on left side of cab Sliding cab side windows Tall wind wings mounted fore of cab windows, left side, and small mirror on right side Standard EMD sunshades with long sunshade tracks Lost-wax brass cast Nathan AirChime K3LA horn mounted to right side cab roof eave. Large Sinclair Excalibur “ice skate” antenna (communications) mounted on a stand centered on the cab roof Accurate hood door and long hood detail Late single-panel inertial compartment with retrofitted latched and hinged access doors Wire inertial air intake grills Tall turbo exhaust stack Standard-range dynamic brakes with 48” fan Late See-through dynamic brake intake grills with horizontal wires through vertical vanes 7-horizontal rib radiator intake grills See-through front and rear 48” radiator fan housings with 8-blade fans; 36” pan-top center radiator fan Curved radiator fan grab iron Square sand fill hatch on top of long hood end Rear LED-illuminated horizontal headlight with lenses Underbody frame rail with separate plumbing Detailed Blomberg-B trucks with Hyatt bearing housings; elliptical springs; end transom detail; separate sanding lines and brackets; deleted outer brake shoes; and separate swing hanger detail Dimensionally accurate truck centers Aeroquip speed recorder on #2 axle, left side. Spare knuckle holders mounted to truck sideframes Frame-mounted bronze bell Prime air filter (can style) 2,600-gallon fuel tank sill skirt removed and relocated vertical gauges; round gauges in fuel tank sides; fuel fillers exposed Factory-applied wire grab irons, photoetched lift rings, windshield wipers, trainline hoses with silver gladhands, air tanks, sand hatch covers and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended radius: 22” DCC & sound equipped locomotives also feature: ESU LokSound 5 DCC & Sound decoder with “Full Throttle” Two (2) cube-type speakers Turbocharged 16-645D3A prime mover sound ESU designed “PowerPack” with two super capacitors*** Operates on both DC and DCC layouts DC/DCC & sound-ready locomotives also feature: Operable on DC layouts DCC-ready with 21-pin connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC ** Class lights illuminate in white color only in DC operation. Access and changing colors requires an ESU decoder with appropriate programming while operating using DCC ***“PowerPack” feature only compatible with appropriately programmed ESU decoders operating on a DCC layout

• DCC vorbereitet (Schnittstelle vorhanden)

New paint scheme Era: Late 80s to Mid-90s Series ATSF 2746 to 2785 (rebuilt between 1982-1984) ATSF 2777 “Faded” ATSF Yellow w/ fresh paint touch-ups at various locations Mounting flanges from removed inertial air intake hoods remaining on long hood roof behind cab EOT antenna stand on right side of cab roof ATSF 2785 “Faded” ATSF Yellow w/ fresh paint touch-ups at various locations Mounting flanges from removed inertial air intake hoods remaining on long hood roof behind cab EOT antenna stand on left side of cab roof All road numbers feature: Front ATSF-style relocated LED-illuminated headlight with lenses in low short hood; blanked number board light mount GP30 cab with increased length on left (fireman’s) side, cab heater vents deleted, and flat center windshield section Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-illuminated “hemisphere” walkway lights on hood ends, and at end of raised walkway duct* Blanked front and rear class lights with round plate LED-illuminated, printed and backlit cab number boards, and blanked long hood end number boards Vapor Corp. cab roof HVAC Front and rear multiple unit (MU) hose catch bars 3-hose multiple unit (MU) hose clusters with silver gladhands Semi-scale coupler buffer equipped with durable metal semi-scale Type E knuckle couplers Front and rear straight uncoupling levers with loop handles; two inner and two outer mounting brackets Modified pilot faces with uncoupling lever loop notches Deck-mounted multiple unit (MU) receptacle Dummy multiple unit (MU) receptacles with cable mounted to pilot face Handrail set with center gangway chains Front and rear standard drop steps Scale sectioned treadplate detail with EMD early “X” style pattern 81” GP30 low short hood with ratchet handbrake, chain guard, and square sand fill Hinged battery box doors with early hinges and narrow louvers Early cab sub-base doors with early hinges Detailed cab interior with separate floor, rear wall, seats, and standard AAR control stand Rectangular vent on left side of cab Sliding cab side windows Tall wind wings mounted fore of cab windows, left side, and small mirror on right side Standard EMD sunshades with long sunshade tracks Lost-wax brass cast Nathan AirChime K3LA horn mounted to right side cab roof eave. Large Sinclair Excalibur “ice skate” antenna (communications) mounted on a stand centered on the cab roof Accurate hood door and long hood detail Late single-panel inertial compartment with retrofitted latched and hinged access doors Wire inertial air intake grills Tall turbo exhaust stack Standard-range dynamic brakes with 48” fan Late See-through dynamic brake intake grills with horizontal wires through vertical vanes 7-horizontal rib radiator intake grills See-through front and rear 48” radiator fan housings with 8-blade fans; 36” pan-top center radiator fan Curved radiator fan grab iron Square sand fill hatch on top of long hood end Rear LED-illuminated horizontal headlight with lenses Underbody frame rail with separate plumbing Detailed Blomberg-B trucks with Hyatt bearing housings; elliptical springs; end transom detail; separate sanding lines and brackets; deleted outer brake shoes; and separate swing hanger detail Dimensionally accurate truck centers Aeroquip speed recorder on #2 axle, left side. Spare knuckle holders mounted to truck sideframes Frame-mounted bronze bell Prime air filter (can style) 2,600-gallon fuel tank sill skirt removed and relocated vertical gauges; round gauges in fuel tank sides; fuel fillers exposed Factory-applied wire grab irons, photoetched lift rings, windshield wipers, trainline hoses with silver gladhands, air tanks, sand hatch covers and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended radius: 22” DCC & sound equipped locomotives also feature: ESU LokSound 5 DCC & Sound decoder with “Full Throttle” Two (2) cube-type speakers Turbocharged 16-645D3A prime mover sound ESU designed “PowerPack” with two super capacitors*** Operates on both DC and DCC layouts DC/DCC & sound-ready locomotives also feature: Operable on DC layouts DCC-ready with 21-pin connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC ** Class lights illuminate in white color only in DC operation. Access and changing colors requires an ESU decoder with appropriate programming while operating using DCC ***“PowerPack” feature only compatible with appropriately programmed ESU decoders operating on a DCC layout

• mit DCC Motordekoder
• mit Sound

Road Number Specific ScaleTrains New road numbers Era: 1994 to 2000 Series 8100 to 8200; built 5-11/1994 Road number 8184 Union Pacific replacement HVAC Replacement engine cab Fully-assembled Multiple road numbers Operating LED-illuminated front deck-mounted ditch lights* Printed and LED-illuminated number boards* Factory-applied detail parts: wire grab irons, trainline hoses with silver gladhands, 3-hose MU clusters with silver gladhands, MU cable, uncoupling levers, windshield wipers, mirrors, sunshades, brake wheel, and more Tall snowplow with open doors and grab irons Semi-scale knuckle couplers – Micro-Trains® compatible 5-step stepwells Walkway with front anticlimber GE “nub” pattern walkway tread Narrow profile end handrails Nose door with window Front LED-illuminated headlight with lenses on low short hood GE safety cab with three (3) side windows Detailed cab interior with floor, rear wall, seats, and desktop Tinted cab side windows Large Sinclair “ice skate” communication antenna and small Sinclair “ice skate” End of Train (EOT) telemetry antenna Motive Equipment Inc. (MEI) ME7000 HVAC Unit Early (curved) engine cab profile Early flanged exhaust stack housing “Bathtub” exhaust silencer Exhaust stack storage cover bracket Standard brake wheel Early radiator door grille pattern (all the same height) Low-mounted rear sandfiller Early lifting lugs on ends of radiator wings Rear LED-illuminated vertical headlight with lenses Accurately profiled frame with separately applied plumbing and traction motor cabling GE Hi-Ad trucks with separately applied brake cylinders and air plumbing Separate air tanks with upper mounting brackets Fuel tank mounted steel bell 5,000 gallon fuel tank Dual fuel fills per side Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Printing and lettering legible under magnification Operates on Code 55 and 80 rail Packaging safely stores model Minimum Radius: 9 ¾” Recommended Radius: 11” DCC & sound equipped locomotives also feature: ESU-LokSound 5 Nano DCC & sound decoder with “Full Throttle” Cube-type speaker Accurate FDL-16 prime mover and auxiliary sounds, horn, bell, and more Operates on both DC and DCC layouts DC/DCC ready locomotives also feature: Operates on DC layouts DCC ready with Nano E24 connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC

• DCC vorbereitet (Schnittstelle vorhanden)

Road Number Specific ScaleTrains All-new model Era: 2009 to Present Series 4400 to 4414; built 1-2/00 Fully-assembled Multiple road numbers Road number 4401 features yellow stripes on nose front and snowplow Unique data and roadnumber placements LED-illuminated front pilot face mounted ditch lights LED-illuminated low-mount cab number boards* Directional LED-illuminated headlights Painted and factory-applied detail parts: wire grab irons; trainline hoses with silver gladhands; 3-hose MU clusters with silver gladhands; MU cable, uncoupling levers; windshield wipers; mirrors; sunshades; brake wheel; and more Tall snowplow with open doors and grab irons Semi-scale Type E knuckle couplers – Micro-Trains® compatible Body mounted coupler box – accepts Micro-Trains® 1015/1016 type couplers without modification 5-step stepwells Walkway with front anticlimber GE “nub” pattern walkway tread Narrow profile end handrails Nose door with window Two-piece nose top grab irons Front LED-illuminated headlight with lenses on low short hood (low headlight) Battery cabinet access door without latch GE safety cab with three (3) side windows Right side cab under floor access doors: dual large louver panels per door Left side cab under floor access doors: dual latch door with grille forward of the HVAC unit Detailed cab interior with floor, rear wall, seats, and desktop Tinted cab side windows Octagonal antenna dome Intermediate: four (4) square bolted panels and three (3) tall horizontal X-panels Continuous reinforcement rib under dynamic brake intake grilles High-capacity dynamic brake exhaust (3-port) Rearward right-side air intake grille Left side auxiliary cab: three (3) short doors with latches on the #2 door; auxiliary cab filter box door Capacitor box on left side walkway Right side auxiliary cab: four (4) doors with latches on #1 and #4 doors Late angled engine cab profile with tri-fold power assembly access doors Lost-wax brass cast Nathan AirChime K3LAR2 horn mounted on engine cab “Bathtub” exhaust silencer 2 individually applied etched metal radiator exhaust grilles. Right side late radiator door grilles in alternating heights Standard brake wheel Left rear hood door grille arrangement: tall, short, tall grilles Low-mounted rear sandfiller Early “box” lifting lugs on ends of radiator wings Rear LED-illuminated vertical headlight with lenses Accurately profiled frame with separately applied plumbing and traction motor cabling Early GE Steerable Trucks with separately applied brake cylinders and air plumbing Dual Graham-White (Salem) 824-100 centrifugal air filters No air dryer 5,000 gallon fuel tank Single fuel fills per side Round and vertical analog fuel gauges; digital fuel gauges Fuel tank mounted steel bell Separate air tanks with lower mounting brackets, connector pipe, and connector pipe cover Early square handbrake chain bracket Spare coupler knuckle holders on rear pilot face Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Printing and lettering legible under magnification Operates on Code 55 and 80 rail Packaging safely stores model Minimum Radius: 9 ¾” Recommended Radius: 11”

• mit DCC Motordekoder
• mit Sound

Take the Operator series HO Scale GE ES44 to the next level with a detail kit. This modeler-applied detail kit includes nearly 100 individual detail parts. Modeling skills are required for painting and assembly. Step-by-step instructions are not included.