• mit DCC Motordekoder
• mit Sound

DM&E/Mt. Rushmore New road numbers Era: As delivered 1976 to early 1980s Series 8035 to 8064;built 9-1976 Fully-assembled Multiple road numbers Class lights (non-operating) Saturn 6552 Strobe Light (non-operating) Printed and LED-illuminated number boards* Front tall pilot plow with high trainline hose cut out, multiple unit (MU) hose doors and grab irons 3-hose multiple unit (MU) hose clusters with silver gladhands Body mounted knuckle couplers; Micro-Trains® compatible Coupler box accepts Micro-Trains 1015/1016 couplers without modification Angled uncoupling levers front and rear and four inner mounting brackets As-delivered pilot faces with reinforced lifting holes Deck mounted multiple unit (MU) receptacle "Tall" stepwells Front and rear early small deck extension Handrail set with inward facing end rail mounting brackets and chain Standard front and rear drop steps Scale sectioned treadplate detail on walkways Rectangle walkway lights mounted between sandbox clean out doors (non-operating) 116” “snoot” low short hood with wheel handbrake Bolted battery box doors with wide louvers Late cab sub-base doors with lift-off hinges Front standard EMD LED-illuminated headlight in number board housing Dash two cab with bolted side window panels Detailed cab interior with floor, rear wall, seats, and standard AAR control stand Rear cab side vent on right side Tall clear wind wings with mirror at top mounted fore and aft of cab side window on both sides of cab Early awning type sunshade Lost wax brass cast Leslie RS-3-L horn with clearance bracket on long hood Motorola ASP-16 “Firecracker” antenna mounted on number board housing Early electrical cabinet "zig-zag" seam, further from rear of cab Early “stand-off” ECAFB Intermediate inertial air intake grills with top drip rail Standard turbo exhaust stack Accurately profiled extended-range dynamic brakes with batten strip Corrugated radiator intake grilles See-through standard 48” radiator fan housings with fan blades visible inside Drop grab radiator fan grab iron Underbody frame rail with separate plumbing and traction motor cables Detailed HT-C trucks with Hyatt bearing caps, late center axle snubbers, sanding lines and brackets GE type speed recorder mounted to third axle on left side Reward facing handbrake chain mount for HTC trucks Short jacking pads (late) Spare knuckle holders on fuel tank near fuel filler Forward engineer’s side sidesill notch Sill-mount EFCO Frame-mounted steel bell Graham-White (Salem) brand 824-170 and 818-170 primary and secondary centrifugal air filters (accordion-style) 4,000-gallon fuel tank with fuel fillers, vertical gauge and round gauge on stand Factory-applied wire grab irons, windshield wipers, trainline hoses with silver gladhands, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED headlights Printing and lettering legible even under magnification Operates on Code 55 and 80 rail Packaging safely stores model Minimum radius: 9 3/4” Recommended radius: 11” DCC & sound equipped locomotives also feature ESU LokSound 5 DCC & Sound decoder with “Full Throttle” One (1) cube-type speaker EMD 16 Cylinder 645E3 prime mover Operates on both DC and DCC layouts DC/DCC & sound ready locomotives also feature Operates on DC layouts DCC ready with E24 connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC

• DCC vorbereitet (Schnittstelle vorhanden)

DM&E/Mt. Rushmore New road numbers Era: As delivered 1976 to early 1980s Series 8035 to 8064;built 9-1976 Fully-assembled Multiple road numbers Class lights (non-operating) Saturn 6552 Strobe Light (non-operating) Printed and LED-illuminated number boards* Front tall pilot plow with high trainline hose cut out, multiple unit (MU) hose doors and grab irons 3-hose multiple unit (MU) hose clusters with silver gladhands Body mounted knuckle couplers; Micro-Trains® compatible Coupler box accepts Micro-Trains 1015/1016 couplers without modification Angled uncoupling levers front and rear and four inner mounting brackets As-delivered pilot faces with reinforced lifting holes Deck mounted multiple unit (MU) receptacle "Tall" stepwells Front and rear early small deck extension Handrail set with inward facing end rail mounting brackets and chain Standard front and rear drop steps Scale sectioned treadplate detail on walkways Rectangle walkway lights mounted between sandbox clean out doors (non-operating) 116” “snoot” low short hood with wheel handbrake Bolted battery box doors with wide louvers Late cab sub-base doors with lift-off hinges Front standard EMD LED-illuminated headlight in number board housing Dash two cab with bolted side window panels Detailed cab interior with floor, rear wall, seats, and standard AAR control stand Rear cab side vent on right side Tall clear wind wings with mirror at top mounted fore and aft of cab side window on both sides of cab Early awning type sunshade Lost wax brass cast Leslie RS-3-L horn with clearance bracket on long hood Motorola ASP-16 “Firecracker” antenna mounted on number board housing Early electrical cabinet "zig-zag" seam, further from rear of cab Early “stand-off” ECAFB Intermediate inertial air intake grills with top drip rail Standard turbo exhaust stack Accurately profiled extended-range dynamic brakes with batten strip Corrugated radiator intake grilles See-through standard 48” radiator fan housings with fan blades visible inside Drop grab radiator fan grab iron Underbody frame rail with separate plumbing and traction motor cables Detailed HT-C trucks with Hyatt bearing caps, late center axle snubbers, sanding lines and brackets GE type speed recorder mounted to third axle on left side Reward facing handbrake chain mount for HTC trucks Short jacking pads (late) Spare knuckle holders on fuel tank near fuel filler Forward engineer’s side sidesill notch Sill-mount EFCO Frame-mounted steel bell Graham-White (Salem) brand 824-170 and 818-170 primary and secondary centrifugal air filters (accordion-style) 4,000-gallon fuel tank with fuel fillers, vertical gauge and round gauge on stand Factory-applied wire grab irons, windshield wipers, trainline hoses with silver gladhands, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED headlights Printing and lettering legible even under magnification Operates on Code 55 and 80 rail Packaging safely stores model Minimum radius: 9 3/4” Recommended radius: 11” DCC & sound equipped locomotives also feature ESU LokSound 5 DCC & Sound decoder with “Full Throttle” One (1) cube-type speaker EMD 16 Cylinder 645E3 prime mover Operates on both DC and DCC layouts DC/DCC & sound ready locomotives also feature Operates on DC layouts DCC ready with E24 connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC

• mit DCC Motordekoder
• mit Sound

CSX/YN3 Boxcar Logo/Yellow Plow New road numbers Era: As delivered 1976 to early 1980s Series 8035 to 8064;built 9-1976 Fully-assembled Multiple road numbers Class lights (non-operating) Saturn 6552 Strobe Light (non-operating) Printed and LED-illuminated number boards* Front tall pilot plow with high trainline hose cut out, multiple unit (MU) hose doors and grab irons 3-hose multiple unit (MU) hose clusters with silver gladhands Body mounted knuckle couplers; Micro-Trains® compatible Coupler box accepts Micro-Trains 1015/1016 couplers without modification Angled uncoupling levers front and rear and four inner mounting brackets As-delivered pilot faces with reinforced lifting holes Deck mounted multiple unit (MU) receptacle "Tall" stepwells Front and rear early small deck extension Handrail set with inward facing end rail mounting brackets and chain Standard front and rear drop steps Scale sectioned treadplate detail on walkways Rectangle walkway lights mounted between sandbox clean out doors (non-operating) 116” “snoot” low short hood with wheel handbrake Bolted battery box doors with wide louvers Late cab sub-base doors with lift-off hinges Front standard EMD LED-illuminated headlight in number board housing Dash two cab with bolted side window panels Detailed cab interior with floor, rear wall, seats, and standard AAR control stand Rear cab side vent on right side Tall clear wind wings with mirror at top mounted fore and aft of cab side window on both sides of cab Early awning type sunshade Lost wax brass cast Leslie RS-3-L horn with clearance bracket on long hood Motorola ASP-16 “Firecracker” antenna mounted on number board housing Early electrical cabinet "zig-zag" seam, further from rear of cab Early “stand-off” ECAFB Intermediate inertial air intake grills with top drip rail Standard turbo exhaust stack Accurately profiled extended-range dynamic brakes with batten strip Corrugated radiator intake grilles See-through standard 48” radiator fan housings with fan blades visible inside Drop grab radiator fan grab iron Underbody frame rail with separate plumbing and traction motor cables Detailed HT-C trucks with Hyatt bearing caps, late center axle snubbers, sanding lines and brackets GE type speed recorder mounted to third axle on left side Reward facing handbrake chain mount for HTC trucks Short jacking pads (late) Spare knuckle holders on fuel tank near fuel filler Forward engineer’s side sidesill notch Sill-mount EFCO Frame-mounted steel bell Graham-White (Salem) brand 824-170 and 818-170 primary and secondary centrifugal air filters (accordion-style) 4,000-gallon fuel tank with fuel fillers, vertical gauge and round gauge on stand Factory-applied wire grab irons, windshield wipers, trainline hoses with silver gladhands, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED headlights Printing and lettering legible even under magnification Operates on Code 55 and 80 rail Packaging safely stores model Minimum radius: 9 3/4” Recommended radius: 11” DCC & sound equipped locomotives also feature ESU LokSound 5 DCC & Sound decoder with “Full Throttle” One (1) cube-type speaker EMD 16 Cylinder 645E3 prime mover Operates on both DC and DCC layouts DC/DCC & sound ready locomotives also feature Operates on DC layouts DCC ready with E24 connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC

• DCC vorbereitet (Schnittstelle vorhanden)

CSX/YN3 Boxcar Logo/Yellow Plow New road numbers Era: As delivered 1976 to early 1980s Series 8035 to 8064;built 9-1976 Fully-assembled Multiple road numbers Class lights (non-operating) Saturn 6552 Strobe Light (non-operating) Printed and LED-illuminated number boards* Front tall pilot plow with high trainline hose cut out, multiple unit (MU) hose doors and grab irons 3-hose multiple unit (MU) hose clusters with silver gladhands Body mounted knuckle couplers; Micro-Trains® compatible Coupler box accepts Micro-Trains 1015/1016 couplers without modification Angled uncoupling levers front and rear and four inner mounting brackets As-delivered pilot faces with reinforced lifting holes Deck mounted multiple unit (MU) receptacle "Tall" stepwells Front and rear early small deck extension Handrail set with inward facing end rail mounting brackets and chain Standard front and rear drop steps Scale sectioned treadplate detail on walkways Rectangle walkway lights mounted between sandbox clean out doors (non-operating) 116” “snoot” low short hood with wheel handbrake Bolted battery box doors with wide louvers Late cab sub-base doors with lift-off hinges Front standard EMD LED-illuminated headlight in number board housing Dash two cab with bolted side window panels Detailed cab interior with floor, rear wall, seats, and standard AAR control stand Rear cab side vent on right side Tall clear wind wings with mirror at top mounted fore and aft of cab side window on both sides of cab Early awning type sunshade Lost wax brass cast Leslie RS-3-L horn with clearance bracket on long hood Motorola ASP-16 “Firecracker” antenna mounted on number board housing Early electrical cabinet "zig-zag" seam, further from rear of cab Early “stand-off” ECAFB Intermediate inertial air intake grills with top drip rail Standard turbo exhaust stack Accurately profiled extended-range dynamic brakes with batten strip Corrugated radiator intake grilles See-through standard 48” radiator fan housings with fan blades visible inside Drop grab radiator fan grab iron Underbody frame rail with separate plumbing and traction motor cables Detailed HT-C trucks with Hyatt bearing caps, late center axle snubbers, sanding lines and brackets GE type speed recorder mounted to third axle on left side Reward facing handbrake chain mount for HTC trucks Short jacking pads (late) Spare knuckle holders on fuel tank near fuel filler Forward engineer’s side sidesill notch Sill-mount EFCO Frame-mounted steel bell Graham-White (Salem) brand 824-170 and 818-170 primary and secondary centrifugal air filters (accordion-style) 4,000-gallon fuel tank with fuel fillers, vertical gauge and round gauge on stand Factory-applied wire grab irons, windshield wipers, trainline hoses with silver gladhands, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED headlights Printing and lettering legible even under magnification Operates on Code 55 and 80 rail Packaging safely stores model Minimum radius: 9 3/4” Recommended radius: 11” DCC & sound equipped locomotives also feature ESU LokSound 5 DCC & Sound decoder with “Full Throttle” One (1) cube-type speaker EMD 16 Cylinder 645E3 prime mover Operates on both DC and DCC layouts DC/DCC & sound ready locomotives also feature Operates on DC layouts DCC ready with E24 connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC

• mit DCC Motordekoder
• mit Sound

CSX/YN3 Boxcar Logo New road numbers Era: As delivered 1976 to early 1980s Series 8035 to 8064;built 9-1976 Fully-assembled Multiple road numbers Class lights (non-operating) Saturn 6552 Strobe Light (non-operating) Printed and LED-illuminated number boards* Front tall pilot plow with high trainline hose cut out, multiple unit (MU) hose doors and grab irons 3-hose multiple unit (MU) hose clusters with silver gladhands Body mounted knuckle couplers; Micro-Trains® compatible Coupler box accepts Micro-Trains 1015/1016 couplers without modification Angled uncoupling levers front and rear and four inner mounting brackets As-delivered pilot faces with reinforced lifting holes Deck mounted multiple unit (MU) receptacle "Tall" stepwells Front and rear early small deck extension Handrail set with inward facing end rail mounting brackets and chain Standard front and rear drop steps Scale sectioned treadplate detail on walkways Rectangle walkway lights mounted between sandbox clean out doors (non-operating) 116” “snoot” low short hood with wheel handbrake Bolted battery box doors with wide louvers Late cab sub-base doors with lift-off hinges Front standard EMD LED-illuminated headlight in number board housing Dash two cab with bolted side window panels Detailed cab interior with floor, rear wall, seats, and standard AAR control stand Rear cab side vent on right side Tall clear wind wings with mirror at top mounted fore and aft of cab side window on both sides of cab Early awning type sunshade Lost wax brass cast Leslie RS-3-L horn with clearance bracket on long hood Motorola ASP-16 “Firecracker” antenna mounted on number board housing Early electrical cabinet "zig-zag" seam, further from rear of cab Early “stand-off” ECAFB Intermediate inertial air intake grills with top drip rail Standard turbo exhaust stack Accurately profiled extended-range dynamic brakes with batten strip Corrugated radiator intake grilles See-through standard 48” radiator fan housings with fan blades visible inside Drop grab radiator fan grab iron Underbody frame rail with separate plumbing and traction motor cables Detailed HT-C trucks with Hyatt bearing caps, late center axle snubbers, sanding lines and brackets GE type speed recorder mounted to third axle on left side Reward facing handbrake chain mount for HTC trucks Short jacking pads (late) Spare knuckle holders on fuel tank near fuel filler Forward engineer’s side sidesill notch Sill-mount EFCO Frame-mounted steel bell Graham-White (Salem) brand 824-170 and 818-170 primary and secondary centrifugal air filters (accordion-style) 4,000-gallon fuel tank with fuel fillers, vertical gauge and round gauge on stand Factory-applied wire grab irons, windshield wipers, trainline hoses with silver gladhands, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED headlights Printing and lettering legible even under magnification Operates on Code 55 and 80 rail Packaging safely stores model Minimum radius: 9 3/4” Recommended radius: 11” DCC & sound equipped locomotives also feature ESU LokSound 5 DCC & Sound decoder with “Full Throttle” One (1) cube-type speaker EMD 16 Cylinder 645E3 prime mover Operates on both DC and DCC layouts DC/DCC & sound ready locomotives also feature Operates on DC layouts DCC ready with E24 connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC

• mit DCC Motordekoder
• mit Sound

CSX/YN3 Boxcar Logo New road numbers Era: As delivered 1976 to early 1980s Series 8035 to 8064;built 9-1976 Fully-assembled Multiple road numbers Class lights (non-operating) Saturn 6552 Strobe Light (non-operating) Printed and LED-illuminated number boards* Front tall pilot plow with high trainline hose cut out, multiple unit (MU) hose doors and grab irons 3-hose multiple unit (MU) hose clusters with silver gladhands Body mounted knuckle couplers; Micro-Trains® compatible Coupler box accepts Micro-Trains 1015/1016 couplers without modification Angled uncoupling levers front and rear and four inner mounting brackets As-delivered pilot faces with reinforced lifting holes Deck mounted multiple unit (MU) receptacle "Tall" stepwells Front and rear early small deck extension Handrail set with inward facing end rail mounting brackets and chain Standard front and rear drop steps Scale sectioned treadplate detail on walkways Rectangle walkway lights mounted between sandbox clean out doors (non-operating) 116” “snoot” low short hood with wheel handbrake Bolted battery box doors with wide louvers Late cab sub-base doors with lift-off hinges Front standard EMD LED-illuminated headlight in number board housing Dash two cab with bolted side window panels Detailed cab interior with floor, rear wall, seats, and standard AAR control stand Rear cab side vent on right side Tall clear wind wings with mirror at top mounted fore and aft of cab side window on both sides of cab Early awning type sunshade Lost wax brass cast Leslie RS-3-L horn with clearance bracket on long hood Motorola ASP-16 “Firecracker” antenna mounted on number board housing Early electrical cabinet "zig-zag" seam, further from rear of cab Early “stand-off” ECAFB Intermediate inertial air intake grills with top drip rail Standard turbo exhaust stack Accurately profiled extended-range dynamic brakes with batten strip Corrugated radiator intake grilles See-through standard 48” radiator fan housings with fan blades visible inside Drop grab radiator fan grab iron Underbody frame rail with separate plumbing and traction motor cables Detailed HT-C trucks with Hyatt bearing caps, late center axle snubbers, sanding lines and brackets GE type speed recorder mounted to third axle on left side Reward facing handbrake chain mount for HTC trucks Short jacking pads (late) Spare knuckle holders on fuel tank near fuel filler Forward engineer’s side sidesill notch Sill-mount EFCO Frame-mounted steel bell Graham-White (Salem) brand 824-170 and 818-170 primary and secondary centrifugal air filters (accordion-style) 4,000-gallon fuel tank with fuel fillers, vertical gauge and round gauge on stand Factory-applied wire grab irons, windshield wipers, trainline hoses with silver gladhands, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED headlights Printing and lettering legible even under magnification Operates on Code 55 and 80 rail Packaging safely stores model Minimum radius: 9 3/4” Recommended radius: 11” DCC & sound equipped locomotives also feature ESU LokSound 5 DCC & Sound decoder with “Full Throttle” One (1) cube-type speaker EMD 16 Cylinder 645E3 prime mover Operates on both DC and DCC layouts DC/DCC & sound ready locomotives also feature Operates on DC layouts DCC ready with E24 connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC

• DCC vorbereitet (Schnittstelle vorhanden)

CSX/YN3 Boxcar Logo New road numbers Era: As delivered 1976 to early 1980s Series 8035 to 8064;built 9-1976 Fully-assembled Multiple road numbers Class lights (non-operating) Saturn 6552 Strobe Light (non-operating) Printed and LED-illuminated number boards* Front tall pilot plow with high trainline hose cut out, multiple unit (MU) hose doors and grab irons 3-hose multiple unit (MU) hose clusters with silver gladhands Body mounted knuckle couplers; Micro-Trains® compatible Coupler box accepts Micro-Trains 1015/1016 couplers without modification Angled uncoupling levers front and rear and four inner mounting brackets As-delivered pilot faces with reinforced lifting holes Deck mounted multiple unit (MU) receptacle "Tall" stepwells Front and rear early small deck extension Handrail set with inward facing end rail mounting brackets and chain Standard front and rear drop steps Scale sectioned treadplate detail on walkways Rectangle walkway lights mounted between sandbox clean out doors (non-operating) 116” “snoot” low short hood with wheel handbrake Bolted battery box doors with wide louvers Late cab sub-base doors with lift-off hinges Front standard EMD LED-illuminated headlight in number board housing Dash two cab with bolted side window panels Detailed cab interior with floor, rear wall, seats, and standard AAR control stand Rear cab side vent on right side Tall clear wind wings with mirror at top mounted fore and aft of cab side window on both sides of cab Early awning type sunshade Lost wax brass cast Leslie RS-3-L horn with clearance bracket on long hood Motorola ASP-16 “Firecracker” antenna mounted on number board housing Early electrical cabinet "zig-zag" seam, further from rear of cab Early “stand-off” ECAFB Intermediate inertial air intake grills with top drip rail Standard turbo exhaust stack Accurately profiled extended-range dynamic brakes with batten strip Corrugated radiator intake grilles See-through standard 48” radiator fan housings with fan blades visible inside Drop grab radiator fan grab iron Underbody frame rail with separate plumbing and traction motor cables Detailed HT-C trucks with Hyatt bearing caps, late center axle snubbers, sanding lines and brackets GE type speed recorder mounted to third axle on left side Reward facing handbrake chain mount for HTC trucks Short jacking pads (late) Spare knuckle holders on fuel tank near fuel filler Forward engineer’s side sidesill notch Sill-mount EFCO Frame-mounted steel bell Graham-White (Salem) brand 824-170 and 818-170 primary and secondary centrifugal air filters (accordion-style) 4,000-gallon fuel tank with fuel fillers, vertical gauge and round gauge on stand Factory-applied wire grab irons, windshield wipers, trainline hoses with silver gladhands, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED headlights Printing and lettering legible even under magnification Operates on Code 55 and 80 rail Packaging safely stores model Minimum radius: 9 3/4” Recommended radius: 11” DCC & sound equipped locomotives also feature ESU LokSound 5 DCC & Sound decoder with “Full Throttle” One (1) cube-type speaker EMD 16 Cylinder 645E3 prime mover Operates on both DC and DCC layouts DC/DCC & sound ready locomotives also feature Operates on DC layouts DCC ready with E24 connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC

• DCC vorbereitet (Schnittstelle vorhanden)

CSX/YN3 Boxcar Logo New road numbers Era: As delivered 1976 to early 1980s Series 8035 to 8064;built 9-1976 Fully-assembled Multiple road numbers Class lights (non-operating) Saturn 6552 Strobe Light (non-operating) Printed and LED-illuminated number boards* Front tall pilot plow with high trainline hose cut out, multiple unit (MU) hose doors and grab irons 3-hose multiple unit (MU) hose clusters with silver gladhands Body mounted knuckle couplers; Micro-Trains® compatible Coupler box accepts Micro-Trains 1015/1016 couplers without modification Angled uncoupling levers front and rear and four inner mounting brackets As-delivered pilot faces with reinforced lifting holes Deck mounted multiple unit (MU) receptacle "Tall" stepwells Front and rear early small deck extension Handrail set with inward facing end rail mounting brackets and chain Standard front and rear drop steps Scale sectioned treadplate detail on walkways Rectangle walkway lights mounted between sandbox clean out doors (non-operating) 116” “snoot” low short hood with wheel handbrake Bolted battery box doors with wide louvers Late cab sub-base doors with lift-off hinges Front standard EMD LED-illuminated headlight in number board housing Dash two cab with bolted side window panels Detailed cab interior with floor, rear wall, seats, and standard AAR control stand Rear cab side vent on right side Tall clear wind wings with mirror at top mounted fore and aft of cab side window on both sides of cab Early awning type sunshade Lost wax brass cast Leslie RS-3-L horn with clearance bracket on long hood Motorola ASP-16 “Firecracker” antenna mounted on number board housing Early electrical cabinet "zig-zag" seam, further from rear of cab Early “stand-off” ECAFB Intermediate inertial air intake grills with top drip rail Standard turbo exhaust stack Accurately profiled extended-range dynamic brakes with batten strip Corrugated radiator intake grilles See-through standard 48” radiator fan housings with fan blades visible inside Drop grab radiator fan grab iron Underbody frame rail with separate plumbing and traction motor cables Detailed HT-C trucks with Hyatt bearing caps, late center axle snubbers, sanding lines and brackets GE type speed recorder mounted to third axle on left side Reward facing handbrake chain mount for HTC trucks Short jacking pads (late) Spare knuckle holders on fuel tank near fuel filler Forward engineer’s side sidesill notch Sill-mount EFCO Frame-mounted steel bell Graham-White (Salem) brand 824-170 and 818-170 primary and secondary centrifugal air filters (accordion-style) 4,000-gallon fuel tank with fuel fillers, vertical gauge and round gauge on stand Factory-applied wire grab irons, windshield wipers, trainline hoses with silver gladhands, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED headlights Printing and lettering legible even under magnification Operates on Code 55 and 80 rail Packaging safely stores model Minimum radius: 9 3/4” Recommended radius: 11” DCC & sound equipped locomotives also feature ESU LokSound 5 DCC & Sound decoder with “Full Throttle” One (1) cube-type speaker EMD 16 Cylinder 645E3 prime mover Operates on both DC and DCC layouts DC/DCC & sound ready locomotives also feature Operates on DC layouts DCC ready with E24 connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC

• mit DCC Motordekoder
• mit Sound

BNSF/Heritage/Small Circle-Cross Nose Logo New road numbers Era: As delivered 1976 to early 1980s Series 8035 to 8064;built 9-1976 Fully-assembled Multiple road numbers Class lights (non-operating) Saturn 6552 Strobe Light (non-operating) Printed and LED-illuminated number boards* Front tall pilot plow with high trainline hose cut out, multiple unit (MU) hose doors and grab irons 3-hose multiple unit (MU) hose clusters with silver gladhands Body mounted knuckle couplers; Micro-Trains® compatible Coupler box accepts Micro-Trains 1015/1016 couplers without modification Angled uncoupling levers front and rear and four inner mounting brackets As-delivered pilot faces with reinforced lifting holes Deck mounted multiple unit (MU) receptacle "Tall" stepwells Front and rear early small deck extension Handrail set with inward facing end rail mounting brackets and chain Standard front and rear drop steps Scale sectioned treadplate detail on walkways Rectangle walkway lights mounted between sandbox clean out doors (non-operating) 116” “snoot” low short hood with wheel handbrake Bolted battery box doors with wide louvers Late cab sub-base doors with lift-off hinges Front standard EMD LED-illuminated headlight in number board housing Dash two cab with bolted side window panels Detailed cab interior with floor, rear wall, seats, and standard AAR control stand Rear cab side vent on right side Tall clear wind wings with mirror at top mounted fore and aft of cab side window on both sides of cab Early awning type sunshade Lost wax brass cast Leslie RS-3-L horn with clearance bracket on long hood Motorola ASP-16 “Firecracker” antenna mounted on number board housing Early electrical cabinet "zig-zag" seam, further from rear of cab Early “stand-off” ECAFB Intermediate inertial air intake grills with top drip rail Standard turbo exhaust stack Accurately profiled extended-range dynamic brakes with batten strip Corrugated radiator intake grilles See-through standard 48” radiator fan housings with fan blades visible inside Drop grab radiator fan grab iron Underbody frame rail with separate plumbing and traction motor cables Detailed HT-C trucks with Hyatt bearing caps, late center axle snubbers, sanding lines and brackets GE type speed recorder mounted to third axle on left side Reward facing handbrake chain mount for HTC trucks Short jacking pads (late) Spare knuckle holders on fuel tank near fuel filler Forward engineer’s side sidesill notch Sill-mount EFCO Frame-mounted steel bell Graham-White (Salem) brand 824-170 and 818-170 primary and secondary centrifugal air filters (accordion-style) 4,000-gallon fuel tank with fuel fillers, vertical gauge and round gauge on stand Factory-applied wire grab irons, windshield wipers, trainline hoses with silver gladhands, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED headlights Printing and lettering legible even under magnification Operates on Code 55 and 80 rail Packaging safely stores model Minimum radius: 9 3/4” Recommended radius: 11” DCC & sound equipped locomotives also feature ESU LokSound 5 DCC & Sound decoder with “Full Throttle” One (1) cube-type speaker EMD 16 Cylinder 645E3 prime mover Operates on both DC and DCC layouts DC/DCC & sound ready locomotives also feature Operates on DC layouts DCC ready with E24 connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC

• mit DCC Motordekoder
• mit Sound

BNSF/Heritage/Small Circle-Cross Nose Logo New road numbers Era: As delivered 1976 to early 1980s Series 8035 to 8064;built 9-1976 Fully-assembled Multiple road numbers Class lights (non-operating) Saturn 6552 Strobe Light (non-operating) Printed and LED-illuminated number boards* Front tall pilot plow with high trainline hose cut out, multiple unit (MU) hose doors and grab irons 3-hose multiple unit (MU) hose clusters with silver gladhands Body mounted knuckle couplers; Micro-Trains® compatible Coupler box accepts Micro-Trains 1015/1016 couplers without modification Angled uncoupling levers front and rear and four inner mounting brackets As-delivered pilot faces with reinforced lifting holes Deck mounted multiple unit (MU) receptacle "Tall" stepwells Front and rear early small deck extension Handrail set with inward facing end rail mounting brackets and chain Standard front and rear drop steps Scale sectioned treadplate detail on walkways Rectangle walkway lights mounted between sandbox clean out doors (non-operating) 116” “snoot” low short hood with wheel handbrake Bolted battery box doors with wide louvers Late cab sub-base doors with lift-off hinges Front standard EMD LED-illuminated headlight in number board housing Dash two cab with bolted side window panels Detailed cab interior with floor, rear wall, seats, and standard AAR control stand Rear cab side vent on right side Tall clear wind wings with mirror at top mounted fore and aft of cab side window on both sides of cab Early awning type sunshade Lost wax brass cast Leslie RS-3-L horn with clearance bracket on long hood Motorola ASP-16 “Firecracker” antenna mounted on number board housing Early electrical cabinet "zig-zag" seam, further from rear of cab Early “stand-off” ECAFB Intermediate inertial air intake grills with top drip rail Standard turbo exhaust stack Accurately profiled extended-range dynamic brakes with batten strip Corrugated radiator intake grilles See-through standard 48” radiator fan housings with fan blades visible inside Drop grab radiator fan grab iron Underbody frame rail with separate plumbing and traction motor cables Detailed HT-C trucks with Hyatt bearing caps, late center axle snubbers, sanding lines and brackets GE type speed recorder mounted to third axle on left side Reward facing handbrake chain mount for HTC trucks Short jacking pads (late) Spare knuckle holders on fuel tank near fuel filler Forward engineer’s side sidesill notch Sill-mount EFCO Frame-mounted steel bell Graham-White (Salem) brand 824-170 and 818-170 primary and secondary centrifugal air filters (accordion-style) 4,000-gallon fuel tank with fuel fillers, vertical gauge and round gauge on stand Factory-applied wire grab irons, windshield wipers, trainline hoses with silver gladhands, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED headlights Printing and lettering legible even under magnification Operates on Code 55 and 80 rail Packaging safely stores model Minimum radius: 9 3/4” Recommended radius: 11” DCC & sound equipped locomotives also feature ESU LokSound 5 DCC & Sound decoder with “Full Throttle” One (1) cube-type speaker EMD 16 Cylinder 645E3 prime mover Operates on both DC and DCC layouts DC/DCC & sound ready locomotives also feature Operates on DC layouts DCC ready with E24 connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC

• DCC vorbereitet (Schnittstelle vorhanden)

BNSF/Heritage/Small Circle-Cross Nose Logo New road numbers Era: As delivered 1976 to early 1980s Series 8035 to 8064;built 9-1976 Fully-assembled Multiple road numbers Class lights (non-operating) Saturn 6552 Strobe Light (non-operating) Printed and LED-illuminated number boards* Front tall pilot plow with high trainline hose cut out, multiple unit (MU) hose doors and grab irons 3-hose multiple unit (MU) hose clusters with silver gladhands Body mounted knuckle couplers; Micro-Trains® compatible Coupler box accepts Micro-Trains 1015/1016 couplers without modification Angled uncoupling levers front and rear and four inner mounting brackets As-delivered pilot faces with reinforced lifting holes Deck mounted multiple unit (MU) receptacle "Tall" stepwells Front and rear early small deck extension Handrail set with inward facing end rail mounting brackets and chain Standard front and rear drop steps Scale sectioned treadplate detail on walkways Rectangle walkway lights mounted between sandbox clean out doors (non-operating) 116” “snoot” low short hood with wheel handbrake Bolted battery box doors with wide louvers Late cab sub-base doors with lift-off hinges Front standard EMD LED-illuminated headlight in number board housing Dash two cab with bolted side window panels Detailed cab interior with floor, rear wall, seats, and standard AAR control stand Rear cab side vent on right side Tall clear wind wings with mirror at top mounted fore and aft of cab side window on both sides of cab Early awning type sunshade Lost wax brass cast Leslie RS-3-L horn with clearance bracket on long hood Motorola ASP-16 “Firecracker” antenna mounted on number board housing Early electrical cabinet "zig-zag" seam, further from rear of cab Early “stand-off” ECAFB Intermediate inertial air intake grills with top drip rail Standard turbo exhaust stack Accurately profiled extended-range dynamic brakes with batten strip Corrugated radiator intake grilles See-through standard 48” radiator fan housings with fan blades visible inside Drop grab radiator fan grab iron Underbody frame rail with separate plumbing and traction motor cables Detailed HT-C trucks with Hyatt bearing caps, late center axle snubbers, sanding lines and brackets GE type speed recorder mounted to third axle on left side Reward facing handbrake chain mount for HTC trucks Short jacking pads (late) Spare knuckle holders on fuel tank near fuel filler Forward engineer’s side sidesill notch Sill-mount EFCO Frame-mounted steel bell Graham-White (Salem) brand 824-170 and 818-170 primary and secondary centrifugal air filters (accordion-style) 4,000-gallon fuel tank with fuel fillers, vertical gauge and round gauge on stand Factory-applied wire grab irons, windshield wipers, trainline hoses with silver gladhands, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED headlights Printing and lettering legible even under magnification Operates on Code 55 and 80 rail Packaging safely stores model Minimum radius: 9 3/4” Recommended radius: 11” DCC & sound equipped locomotives also feature ESU LokSound 5 DCC & Sound decoder with “Full Throttle” One (1) cube-type speaker EMD 16 Cylinder 645E3 prime mover Operates on both DC and DCC layouts DC/DCC & sound ready locomotives also feature Operates on DC layouts DCC ready with E24 connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC

• mit DCC Motordekoder
• mit Sound

BNSF/Heritage I/Large Circle-Cross Nose Logo New road numbers Era: As delivered 1976 to early 1980s Series 8035 to 8064;built 9-1976 Fully-assembled Multiple road numbers Class lights (non-operating) Saturn 6552 Strobe Light (non-operating) Printed and LED-illuminated number boards* Front tall pilot plow with high trainline hose cut out, multiple unit (MU) hose doors and grab irons 3-hose multiple unit (MU) hose clusters with silver gladhands Body mounted knuckle couplers; Micro-Trains® compatible Coupler box accepts Micro-Trains 1015/1016 couplers without modification Angled uncoupling levers front and rear and four inner mounting brackets As-delivered pilot faces with reinforced lifting holes Deck mounted multiple unit (MU) receptacle "Tall" stepwells Front and rear early small deck extension Handrail set with inward facing end rail mounting brackets and chain Standard front and rear drop steps Scale sectioned treadplate detail on walkways Rectangle walkway lights mounted between sandbox clean out doors (non-operating) 116” “snoot” low short hood with wheel handbrake Bolted battery box doors with wide louvers Late cab sub-base doors with lift-off hinges Front standard EMD LED-illuminated headlight in number board housing Dash two cab with bolted side window panels Detailed cab interior with floor, rear wall, seats, and standard AAR control stand Rear cab side vent on right side Tall clear wind wings with mirror at top mounted fore and aft of cab side window on both sides of cab Early awning type sunshade Lost wax brass cast Leslie RS-3-L horn with clearance bracket on long hood Motorola ASP-16 “Firecracker” antenna mounted on number board housing Early electrical cabinet "zig-zag" seam, further from rear of cab Early “stand-off” ECAFB Intermediate inertial air intake grills with top drip rail Standard turbo exhaust stack Accurately profiled extended-range dynamic brakes with batten strip Corrugated radiator intake grilles See-through standard 48” radiator fan housings with fan blades visible inside Drop grab radiator fan grab iron Underbody frame rail with separate plumbing and traction motor cables Detailed HT-C trucks with Hyatt bearing caps, late center axle snubbers, sanding lines and brackets GE type speed recorder mounted to third axle on left side Reward facing handbrake chain mount for HTC trucks Short jacking pads (late) Spare knuckle holders on fuel tank near fuel filler Forward engineer’s side sidesill notch Sill-mount EFCO Frame-mounted steel bell Graham-White (Salem) brand 824-170 and 818-170 primary and secondary centrifugal air filters (accordion-style) 4,000-gallon fuel tank with fuel fillers, vertical gauge and round gauge on stand Factory-applied wire grab irons, windshield wipers, trainline hoses with silver gladhands, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED headlights Printing and lettering legible even under magnification Operates on Code 55 and 80 rail Packaging safely stores model Minimum radius: 9 3/4” Recommended radius: 11” DCC & sound equipped locomotives also feature ESU LokSound 5 DCC & Sound decoder with “Full Throttle” One (1) cube-type speaker EMD 16 Cylinder 645E3 prime mover Operates on both DC and DCC layouts DC/DCC & sound ready locomotives also feature Operates on DC layouts DCC ready with E24 connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC

• mit DCC Motordekoder
• mit Sound

BNSF/Heritage I/Large Circle-Cross Nose Logo New road numbers Era: As delivered 1976 to early 1980s Series 8035 to 8064;built 9-1976 Fully-assembled Multiple road numbers Class lights (non-operating) Saturn 6552 Strobe Light (non-operating) Printed and LED-illuminated number boards* Front tall pilot plow with high trainline hose cut out, multiple unit (MU) hose doors and grab irons 3-hose multiple unit (MU) hose clusters with silver gladhands Body mounted knuckle couplers; Micro-Trains® compatible Coupler box accepts Micro-Trains 1015/1016 couplers without modification Angled uncoupling levers front and rear and four inner mounting brackets As-delivered pilot faces with reinforced lifting holes Deck mounted multiple unit (MU) receptacle "Tall" stepwells Front and rear early small deck extension Handrail set with inward facing end rail mounting brackets and chain Standard front and rear drop steps Scale sectioned treadplate detail on walkways Rectangle walkway lights mounted between sandbox clean out doors (non-operating) 116” “snoot” low short hood with wheel handbrake Bolted battery box doors with wide louvers Late cab sub-base doors with lift-off hinges Front standard EMD LED-illuminated headlight in number board housing Dash two cab with bolted side window panels Detailed cab interior with floor, rear wall, seats, and standard AAR control stand Rear cab side vent on right side Tall clear wind wings with mirror at top mounted fore and aft of cab side window on both sides of cab Early awning type sunshade Lost wax brass cast Leslie RS-3-L horn with clearance bracket on long hood Motorola ASP-16 “Firecracker” antenna mounted on number board housing Early electrical cabinet "zig-zag" seam, further from rear of cab Early “stand-off” ECAFB Intermediate inertial air intake grills with top drip rail Standard turbo exhaust stack Accurately profiled extended-range dynamic brakes with batten strip Corrugated radiator intake grilles See-through standard 48” radiator fan housings with fan blades visible inside Drop grab radiator fan grab iron Underbody frame rail with separate plumbing and traction motor cables Detailed HT-C trucks with Hyatt bearing caps, late center axle snubbers, sanding lines and brackets GE type speed recorder mounted to third axle on left side Reward facing handbrake chain mount for HTC trucks Short jacking pads (late) Spare knuckle holders on fuel tank near fuel filler Forward engineer’s side sidesill notch Sill-mount EFCO Frame-mounted steel bell Graham-White (Salem) brand 824-170 and 818-170 primary and secondary centrifugal air filters (accordion-style) 4,000-gallon fuel tank with fuel fillers, vertical gauge and round gauge on stand Factory-applied wire grab irons, windshield wipers, trainline hoses with silver gladhands, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED headlights Printing and lettering legible even under magnification Operates on Code 55 and 80 rail Packaging safely stores model Minimum radius: 9 3/4” Recommended radius: 11” DCC & sound equipped locomotives also feature ESU LokSound 5 DCC & Sound decoder with “Full Throttle” One (1) cube-type speaker EMD 16 Cylinder 645E3 prime mover Operates on both DC and DCC layouts DC/DCC & sound ready locomotives also feature Operates on DC layouts DCC ready with E24 connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC

• DCC vorbereitet (Schnittstelle vorhanden)

BNSF/Heritage I/Large Circle-Cross Nose Logo New road numbers Era: As delivered 1976 to early 1980s Series 8035 to 8064;built 9-1976 Fully-assembled Multiple road numbers Class lights (non-operating) Saturn 6552 Strobe Light (non-operating) Printed and LED-illuminated number boards* Front tall pilot plow with high trainline hose cut out, multiple unit (MU) hose doors and grab irons 3-hose multiple unit (MU) hose clusters with silver gladhands Body mounted knuckle couplers; Micro-Trains® compatible Coupler box accepts Micro-Trains 1015/1016 couplers without modification Angled uncoupling levers front and rear and four inner mounting brackets As-delivered pilot faces with reinforced lifting holes Deck mounted multiple unit (MU) receptacle "Tall" stepwells Front and rear early small deck extension Handrail set with inward facing end rail mounting brackets and chain Standard front and rear drop steps Scale sectioned treadplate detail on walkways Rectangle walkway lights mounted between sandbox clean out doors (non-operating) 116” “snoot” low short hood with wheel handbrake Bolted battery box doors with wide louvers Late cab sub-base doors with lift-off hinges Front standard EMD LED-illuminated headlight in number board housing Dash two cab with bolted side window panels Detailed cab interior with floor, rear wall, seats, and standard AAR control stand Rear cab side vent on right side Tall clear wind wings with mirror at top mounted fore and aft of cab side window on both sides of cab Early awning type sunshade Lost wax brass cast Leslie RS-3-L horn with clearance bracket on long hood Motorola ASP-16 “Firecracker” antenna mounted on number board housing Early electrical cabinet "zig-zag" seam, further from rear of cab Early “stand-off” ECAFB Intermediate inertial air intake grills with top drip rail Standard turbo exhaust stack Accurately profiled extended-range dynamic brakes with batten strip Corrugated radiator intake grilles See-through standard 48” radiator fan housings with fan blades visible inside Drop grab radiator fan grab iron Underbody frame rail with separate plumbing and traction motor cables Detailed HT-C trucks with Hyatt bearing caps, late center axle snubbers, sanding lines and brackets GE type speed recorder mounted to third axle on left side Reward facing handbrake chain mount for HTC trucks Short jacking pads (late) Spare knuckle holders on fuel tank near fuel filler Forward engineer’s side sidesill notch Sill-mount EFCO Frame-mounted steel bell Graham-White (Salem) brand 824-170 and 818-170 primary and secondary centrifugal air filters (accordion-style) 4,000-gallon fuel tank with fuel fillers, vertical gauge and round gauge on stand Factory-applied wire grab irons, windshield wipers, trainline hoses with silver gladhands, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED headlights Printing and lettering legible even under magnification Operates on Code 55 and 80 rail Packaging safely stores model Minimum radius: 9 3/4” Recommended radius: 11” DCC & sound equipped locomotives also feature ESU LokSound 5 DCC & Sound decoder with “Full Throttle” One (1) cube-type speaker EMD 16 Cylinder 645E3 prime mover Operates on both DC and DCC layouts DC/DCC & sound ready locomotives also feature Operates on DC layouts DCC ready with E24 connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC

• DCC vorbereitet (Schnittstelle vorhanden)

BNSF/Heritage I/Large Circle-Cross Nose Logo New road numbers Era: As delivered 1976 to early 1980s Series 8035 to 8064;built 9-1976 Fully-assembled Multiple road numbers Class lights (non-operating) Saturn 6552 Strobe Light (non-operating) Printed and LED-illuminated number boards* Front tall pilot plow with high trainline hose cut out, multiple unit (MU) hose doors and grab irons 3-hose multiple unit (MU) hose clusters with silver gladhands Body mounted knuckle couplers; Micro-Trains® compatible Coupler box accepts Micro-Trains 1015/1016 couplers without modification Angled uncoupling levers front and rear and four inner mounting brackets As-delivered pilot faces with reinforced lifting holes Deck mounted multiple unit (MU) receptacle "Tall" stepwells Front and rear early small deck extension Handrail set with inward facing end rail mounting brackets and chain Standard front and rear drop steps Scale sectioned treadplate detail on walkways Rectangle walkway lights mounted between sandbox clean out doors (non-operating) 116” “snoot” low short hood with wheel handbrake Bolted battery box doors with wide louvers Late cab sub-base doors with lift-off hinges Front standard EMD LED-illuminated headlight in number board housing Dash two cab with bolted side window panels Detailed cab interior with floor, rear wall, seats, and standard AAR control stand Rear cab side vent on right side Tall clear wind wings with mirror at top mounted fore and aft of cab side window on both sides of cab Early awning type sunshade Lost wax brass cast Leslie RS-3-L horn with clearance bracket on long hood Motorola ASP-16 “Firecracker” antenna mounted on number board housing Early electrical cabinet "zig-zag" seam, further from rear of cab Early “stand-off” ECAFB Intermediate inertial air intake grills with top drip rail Standard turbo exhaust stack Accurately profiled extended-range dynamic brakes with batten strip Corrugated radiator intake grilles See-through standard 48” radiator fan housings with fan blades visible inside Drop grab radiator fan grab iron Underbody frame rail with separate plumbing and traction motor cables Detailed HT-C trucks with Hyatt bearing caps, late center axle snubbers, sanding lines and brackets GE type speed recorder mounted to third axle on left side Reward facing handbrake chain mount for HTC trucks Short jacking pads (late) Spare knuckle holders on fuel tank near fuel filler Forward engineer’s side sidesill notch Sill-mount EFCO Frame-mounted steel bell Graham-White (Salem) brand 824-170 and 818-170 primary and secondary centrifugal air filters (accordion-style) 4,000-gallon fuel tank with fuel fillers, vertical gauge and round gauge on stand Factory-applied wire grab irons, windshield wipers, trainline hoses with silver gladhands, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED headlights Printing and lettering legible even under magnification Operates on Code 55 and 80 rail Packaging safely stores model Minimum radius: 9 3/4” Recommended radius: 11” DCC & sound equipped locomotives also feature ESU LokSound 5 DCC & Sound decoder with “Full Throttle” One (1) cube-type speaker EMD 16 Cylinder 645E3 prime mover Operates on both DC and DCC layouts DC/DCC & sound ready locomotives also feature Operates on DC layouts DCC ready with E24 connector * Lighting features operate when using an ESU decoder with appropriate programming while operating using DCC

Neuerscheinung! Auslieferung Juni 2026

• mit DCC Motordekoder
• mit Sound

Road Number Specific ScaleTrains New road numbers Era: 2016 to present Series 2670 to 2739; built 7-9/2016 Fully-assembled Multiple road numbers Operating LED ground lights on both sides of locomotive* Operating LED front, rear, and side walkway lights* Operating LED front deck mounted ditch lights Printed and LED lighted number boards* Semi-scale coupler buffers equipped with durable metal semi-scale standard Type E knuckle couplers Multiple unit (MU) cable without attachment chain; wireworm holding brackets mounted under front anticlimber; and rear fixed drop step See-through round-hole stepwell steps Walkway with front anticlimber GE “nub” pattern walkway tread Sand box clean out door with handle and rotating hinge Narrow profile end handrails Front nose headlight Nose door without window Cab with barrel bolt latches on subbase doors Detailed cab interior with separate floor, rear wall, seats, and control stand In cab grade crossing camera mounted on left side Tinted cab side windows Tall mirror mounted in front of sliding cab side windows on both sides; additional small mirror on right side Cab roof JEM Communications PTC antenna farm with triple conduit between front and rear cabinets See-through dynamic brake exhaust Left side dynamic brake cab: tri blower dynamic brake with flush exhaust Etched metal see-through dynamic brake intake grilles with blower motors visible inside Right side dynamic brake cab: door with grille, door with grille, small grille, and door with grille Current production engine cab (long hood) with angled exhaust compartment roofline Lost wax brass cast Nathan AirChime K5HLR2 horn mounted on engine cab roof Separate exhaust stack 40 individually applied etched metal see-through radiator intake and exhaust grilles on sides and top of radiator compartment Standard production radiator door grilles Standard radiator grille cover hold downs Raised center brake wheel Accurately profiled frame with separately applied plumbing and traction motor cabling GE Hi-Ad trucks with separately applied brake cylinders, air plumbing, and rotating bearing caps Rust-color painted wheelsets AEI tag mounted on right sidesill 5,300 gallon fuel tank with external waste retention tank Dual fuel fills per side with rear fill “blanked” Factory-applied wire grab irons, snowplow with grab irons, spare knuckles, trainline hoses with silver gladhands, 3-hose MU clusters with silver gladhands, uncoupling levers, windshield wipers, mirrors, sunshades, air dryer, air tanks, fuel tank mounted electronic bell, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum Radius: 18” Recommended Radius: 22” DCC & sound equipped locomotives also feature: ESU-LokSound 5 DCC and Sound decoder Two (2) cube-type speakers Accurate GEVO-12 prime mover and auxiliary sounds, horn, bell, and more ESU-designed PowerPack with two (2) super capacitors*** Operates on both DC and DCC layouts

Neuerscheinung! Auslieferung Juni 2026

• mit DCC Motordekoder
• mit Sound

Road Number Specific ScaleTrains New road numbers Era: 2016 to present Series 2670 to 2739; built 7-9/2016 Fully-assembled Multiple road numbers Operating LED ground lights on both sides of locomotive* Operating LED front, rear, and side walkway lights* Operating LED front deck mounted ditch lights Printed and LED lighted number boards* Semi-scale coupler buffers equipped with durable metal semi-scale standard Type E knuckle couplers Multiple unit (MU) cable without attachment chain; wireworm holding brackets mounted under front anticlimber; and rear fixed drop step See-through round-hole stepwell steps Walkway with front anticlimber GE “nub” pattern walkway tread Sand box clean out door with handle and rotating hinge Narrow profile end handrails Front nose headlight Nose door without window Cab with barrel bolt latches on subbase doors Detailed cab interior with separate floor, rear wall, seats, and control stand In cab grade crossing camera mounted on left side Tinted cab side windows Tall mirror mounted in front of sliding cab side windows on both sides; additional small mirror on right side Cab roof JEM Communications PTC antenna farm with triple conduit between front and rear cabinets See-through dynamic brake exhaust Left side dynamic brake cab: tri blower dynamic brake with flush exhaust Etched metal see-through dynamic brake intake grilles with blower motors visible inside Right side dynamic brake cab: door with grille, door with grille, small grille, and door with grille Current production engine cab (long hood) with angled exhaust compartment roofline Lost wax brass cast Nathan AirChime K5HLR2 horn mounted on engine cab roof Separate exhaust stack 40 individually applied etched metal see-through radiator intake and exhaust grilles on sides and top of radiator compartment Standard production radiator door grilles Standard radiator grille cover hold downs Raised center brake wheel Accurately profiled frame with separately applied plumbing and traction motor cabling GE Hi-Ad trucks with separately applied brake cylinders, air plumbing, and rotating bearing caps Rust-color painted wheelsets AEI tag mounted on right sidesill 5,300 gallon fuel tank with external waste retention tank Dual fuel fills per side with rear fill “blanked” Factory-applied wire grab irons, snowplow with grab irons, spare knuckles, trainline hoses with silver gladhands, 3-hose MU clusters with silver gladhands, uncoupling levers, windshield wipers, mirrors, sunshades, air dryer, air tanks, fuel tank mounted electronic bell, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum Radius: 18” Recommended Radius: 22” DCC & sound equipped locomotives also feature: ESU-LokSound 5 DCC and Sound decoder Two (2) cube-type speakers Accurate GEVO-12 prime mover and auxiliary sounds, horn, bell, and more ESU-designed PowerPack with two (2) super capacitors*** Operates on both DC and DCC layouts

Neuerscheinung! Auslieferung Juni 2026

• mit DCC Motordekoder
• mit Sound

Road Number Specific ScaleTrains New road numbers Era: 2016 to present Series 2670 to 2739; built 7-9/2016 Fully-assembled Multiple road numbers Operating LED ground lights on both sides of locomotive* Operating LED front, rear, and side walkway lights* Operating LED front deck mounted ditch lights Printed and LED lighted number boards* Semi-scale coupler buffers equipped with durable metal semi-scale standard Type E knuckle couplers Multiple unit (MU) cable without attachment chain; wireworm holding brackets mounted under front anticlimber; and rear fixed drop step See-through round-hole stepwell steps Walkway with front anticlimber GE “nub” pattern walkway tread Sand box clean out door with handle and rotating hinge Narrow profile end handrails Front nose headlight Nose door without window Cab with barrel bolt latches on subbase doors Detailed cab interior with separate floor, rear wall, seats, and control stand In cab grade crossing camera mounted on left side Tinted cab side windows Tall mirror mounted in front of sliding cab side windows on both sides; additional small mirror on right side Cab roof JEM Communications PTC antenna farm with triple conduit between front and rear cabinets See-through dynamic brake exhaust Left side dynamic brake cab: tri blower dynamic brake with flush exhaust Etched metal see-through dynamic brake intake grilles with blower motors visible inside Right side dynamic brake cab: door with grille, door with grille, small grille, and door with grille Current production engine cab (long hood) with angled exhaust compartment roofline Lost wax brass cast Nathan AirChime K5HLR2 horn mounted on engine cab roof Separate exhaust stack 40 individually applied etched metal see-through radiator intake and exhaust grilles on sides and top of radiator compartment Standard production radiator door grilles Standard radiator grille cover hold downs Raised center brake wheel Accurately profiled frame with separately applied plumbing and traction motor cabling GE Hi-Ad trucks with separately applied brake cylinders, air plumbing, and rotating bearing caps Rust-color painted wheelsets AEI tag mounted on right sidesill 5,300 gallon fuel tank with external waste retention tank Dual fuel fills per side with rear fill “blanked” Factory-applied wire grab irons, snowplow with grab irons, spare knuckles, trainline hoses with silver gladhands, 3-hose MU clusters with silver gladhands, uncoupling levers, windshield wipers, mirrors, sunshades, air dryer, air tanks, fuel tank mounted electronic bell, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum Radius: 18” Recommended Radius: 22” DCC & sound equipped locomotives also feature: ESU-LokSound 5 DCC and Sound decoder Two (2) cube-type speakers Accurate GEVO-12 prime mover and auxiliary sounds, horn, bell, and more ESU-designed PowerPack with two (2) super capacitors*** Operates on both DC and DCC layouts

Neuerscheinung! Auslieferung Juni 2026

• DCC vorbereitet (Schnittstelle vorhanden)

Road Number Specific ScaleTrains New road numbers Era: 2016 to present Series 2670 to 2739; built 7-9/2016 Fully-assembled Multiple road numbers Operating LED ground lights on both sides of locomotive* Operating LED front, rear, and side walkway lights* Operating LED front deck mounted ditch lights Printed and LED lighted number boards* Semi-scale coupler buffers equipped with durable metal semi-scale standard Type E knuckle couplers Multiple unit (MU) cable without attachment chain; wireworm holding brackets mounted under front anticlimber; and rear fixed drop step See-through round-hole stepwell steps Walkway with front anticlimber GE “nub” pattern walkway tread Sand box clean out door with handle and rotating hinge Narrow profile end handrails Front nose headlight Nose door without window Cab with barrel bolt latches on subbase doors Detailed cab interior with separate floor, rear wall, seats, and control stand In cab grade crossing camera mounted on left side Tinted cab side windows Tall mirror mounted in front of sliding cab side windows on both sides; additional small mirror on right side Cab roof JEM Communications PTC antenna farm with triple conduit between front and rear cabinets See-through dynamic brake exhaust Left side dynamic brake cab: tri blower dynamic brake with flush exhaust Etched metal see-through dynamic brake intake grilles with blower motors visible inside Right side dynamic brake cab: door with grille, door with grille, small grille, and door with grille Current production engine cab (long hood) with angled exhaust compartment roofline Lost wax brass cast Nathan AirChime K5HLR2 horn mounted on engine cab roof Separate exhaust stack 40 individually applied etched metal see-through radiator intake and exhaust grilles on sides and top of radiator compartment Standard production radiator door grilles Standard radiator grille cover hold downs Raised center brake wheel Accurately profiled frame with separately applied plumbing and traction motor cabling GE Hi-Ad trucks with separately applied brake cylinders, air plumbing, and rotating bearing caps Rust-color painted wheelsets AEI tag mounted on right sidesill 5,300 gallon fuel tank with external waste retention tank Dual fuel fills per side with rear fill “blanked” Factory-applied wire grab irons, snowplow with grab irons, spare knuckles, trainline hoses with silver gladhands, 3-hose MU clusters with silver gladhands, uncoupling levers, windshield wipers, mirrors, sunshades, air dryer, air tanks, fuel tank mounted electronic bell, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum Radius: 18” Recommended Radius: 22” DCC & sound ready locomotives also feature: Operates on DC layouts DCC ready with 21-pin connector

Neuerscheinung! Auslieferung Juni 2026

• DCC vorbereitet (Schnittstelle vorhanden)

Road Number Specific ScaleTrains New road numbers Era: 2016 to present Series 2670 to 2739; built 7-9/2016 Fully-assembled Multiple road numbers Operating LED ground lights on both sides of locomotive* Operating LED front, rear, and side walkway lights* Operating LED front deck mounted ditch lights Printed and LED lighted number boards* Semi-scale coupler buffers equipped with durable metal semi-scale standard Type E knuckle couplers Multiple unit (MU) cable without attachment chain; wireworm holding brackets mounted under front anticlimber; and rear fixed drop step See-through round-hole stepwell steps Walkway with front anticlimber GE “nub” pattern walkway tread Sand box clean out door with handle and rotating hinge Narrow profile end handrails Front nose headlight Nose door without window Cab with barrel bolt latches on subbase doors Detailed cab interior with separate floor, rear wall, seats, and control stand In cab grade crossing camera mounted on left side Tinted cab side windows Tall mirror mounted in front of sliding cab side windows on both sides; additional small mirror on right side Cab roof JEM Communications PTC antenna farm with triple conduit between front and rear cabinets See-through dynamic brake exhaust Left side dynamic brake cab: tri blower dynamic brake with flush exhaust Etched metal see-through dynamic brake intake grilles with blower motors visible inside Right side dynamic brake cab: door with grille, door with grille, small grille, and door with grille Current production engine cab (long hood) with angled exhaust compartment roofline Lost wax brass cast Nathan AirChime K5HLR2 horn mounted on engine cab roof Separate exhaust stack 40 individually applied etched metal see-through radiator intake and exhaust grilles on sides and top of radiator compartment Standard production radiator door grilles Standard radiator grille cover hold downs Raised center brake wheel Accurately profiled frame with separately applied plumbing and traction motor cabling GE Hi-Ad trucks with separately applied brake cylinders, air plumbing, and rotating bearing caps Rust-color painted wheelsets AEI tag mounted on right sidesill 5,300 gallon fuel tank with external waste retention tank Dual fuel fills per side with rear fill “blanked” Factory-applied wire grab irons, snowplow with grab irons, spare knuckles, trainline hoses with silver gladhands, 3-hose MU clusters with silver gladhands, uncoupling levers, windshield wipers, mirrors, sunshades, air dryer, air tanks, fuel tank mounted electronic bell, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum Radius: 18” Recommended Radius: 22” DCC & sound ready locomotives also feature: Operates on DC layouts DCC ready with 21-pin connector