Sie sind hier:
Neuerscheinung! Auslieferung Dezember 2024
Vorbestellfrist für garantierte Lieferung: 26.02.2024
Road Number Specific ScaleTrains Era: 2023 to present Road number 1973 Special Chessie System Heritage scheme Series 3000 to 3064; built 4-6:2012 Formerly CSX 3049 Inverter Cabinet with Bolted and hinged access door, Front Top X Panel Wider Than Rear X Panel, three lower X panels with 4 - 6 - 4 Bolt Pattern Lower X Panels Lost wax brass cast Nathan AirChime K5HLR2 horn mounted on engine cab roof Retrofitted late ET44 style exhaust stack, no flange or center support on stack Fully-assembled LED-illuminated ground lights on both sides of locomotive* LED-illuminated front, rear and rectangle side walkway lights* LED-illuminated front deck-mounted alternating ditch lights** Printed and LED-illuminated lighted number boards* LSL (Locomotive Speed Limiter) indicator lights on cab sides (non-operating) Sill-mounted tow chain Semi-scale coupler buffers equipped with die-cast metal semi-scale SBE bottom shelf knuckle couplers Inside loop uncoupling levers with up down brackets Single trainline hose with silver gladhand Pilot-mounted battery charging receptacles Front dummy Multiple Unit (MU) receptacles mounted to pilot face Front and rear raised pilot-mounted Multiple Unit (MU) receptacles Front and rear single ECP brake equipment box and cable mounted on pilot face See-through round-hole stepwell steps Walkway with front anticlimber; no support brackets GE “nub” pattern walkway tread Late handrails with U-bolt caps and narrow rear most stanchion on long side rails Wide profile end handrails Sand box clean out door with knuckle buster latch Front nose headlight Front straight grab irons mounted directly to the nose Front right side mounted narrow nose drop grab iron Right nose door with window Front high-mounted (cab) numberboard housings Dual cab side blue flag holder Left side under cab front access bolted X panel; rear door with square corrugated grille Late cab with barrel bolt latches on subbase doors Detailed cab interior with separate floor, rear wall, seats, and control stand In cab grade crossing camera mounted on right side Tinted cab side windows Tall mirror mounted in front of sliding cab side windows on both sides Switching mirror mounted between rear of sliding cab side windows and fixed rear window on engineer’s side Cab roof GE communications handler octagonal dome and dual long STI-CO PTC Dual Track Antenna System without Radome covers See-through dynamic brake exhaust Left side dynamic brake cab: tri blower dynamic brake with flush exhaust Etched metal see-through dynamic brake intake grilles with blower motors visible inside Right side dynamic brake cab: door with grille, small grille, door with grille, and door with grille Dynamic brake cab door with high door handle and high mounted door handle bumper Long right side air intake grille Left side auxiliary cab: 3 tall doors with latches on the #2 door and no auxiliary cab filter box door Right side auxiliary cab: raised X panel door; 3 doors with latches on #2 and #3 doors ES44 style engine cab doors: latched first door in each set of three Three engine cab roof lift rings Left side exhaust cab doors: latched last door in set of three Flush heat exchanger housing with single piece narrow slot grille Late raised radiator grille 22 individually applied etched metal see-through radiator intake and exhaust grilles on sides and top of radiator compartment Left side radiator cab grille arrangement: Raised doors. Grilles - tall-short-tall-short-tall, no grille under brake wheel short front angled grille and two-piece rear angled grille Right side radiator cab grille arrangement: Raised doors. Grilles – tall, short, tall, short, short, tall, short, tall, short front angled grill, two-piece rear angled grille Flat water fill box with sight glass High mounted horizontal rear headlight Rear narrow-spaced dual dummy Multiple Unit (MU) receptacles Accurately profiled frame with separately applied plumbing and cabling Late GE steerable trucks with separately applied brake cylinders, air plumbing, rotating bearing caps, and reinforcement bar under center journal Rust-color painted wheelsets Square handbrake chain bracket Toilet drain with exterior handle AEI tag mounted to right sidesill under rear battery box door Dual Graham-White (Prime) finned 075 air filters Graham-White 994-500 air dryer 5,300-gallon fuel tank with internal waste retention tank, digital fuel gauge, vertical fuel gauge, and round fuel gauge Dual fuel fills per side with rear fill “blanked” Flat top left side fuel tank top box Long crankcase drainpipe attached to the end of the fuel tank Low snowplow without MU doors Factory-applied wire grab irons, snowplow with grab irons, spare knuckles, trainline hoses with silver gladhands, 3-hose MU clusters with silver gladhands, uncoupling levers, windshield wipers, mirrors, sunshades, air tanks, fuel tank mounted electronic bell, brake wheel, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED headlights Printing and lettering legible under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum Radius: 18” Recommended Radius: 22” ESU-LokSound 5 DCC and Sound decoder with “Full Throttle” Two (2) cube-type speakers Accurate GEVO-12 prime mover and auxiliary sounds, horn, bell, and more ESU-designed PowerPack with two (2) super capacitors*** Operates on both DC and DCC layouts
Produktgewicht inkl. Verpackung: 1,320 kgNeuerscheinung! Auslieferung Dezember 2024
Vorbestellfrist für garantierte Lieferung: 26.02.2024
Road Number Specific ScaleTrains Era: 2023 to present Road number 1973 Special Chessie System Heritage scheme Series 3000 to 3064; built 4-6:2012 Formerly CSX 3049 Inverter Cabinet with Bolted and hinged access door, Front Top X Panel Wider Than Rear X Panel, three lower X panels with 4 - 6 - 4 Bolt Pattern Lower X Panels Lost wax brass cast Nathan AirChime K5HLR2 horn mounted on engine cab roof Retrofitted late ET44 style exhaust stack, no flange or center support on stack Fully-assembled LED-illuminated ground lights on both sides of locomotive* LED-illuminated front, rear and rectangle side walkway lights* LED-illuminated front deck-mounted alternating ditch lights** Printed and LED-illuminated lighted number boards* LSL (Locomotive Speed Limiter) indicator lights on cab sides (non-operating) Sill-mounted tow chain Semi-scale coupler buffers equipped with die-cast metal semi-scale SBE bottom shelf knuckle couplers Inside loop uncoupling levers with up down brackets Single trainline hose with silver gladhand Pilot-mounted battery charging receptacles Front dummy Multiple Unit (MU) receptacles mounted to pilot face Front and rear raised pilot-mounted Multiple Unit (MU) receptacles Front and rear single ECP brake equipment box and cable mounted on pilot face See-through round-hole stepwell steps Walkway with front anticlimber; no support brackets GE “nub” pattern walkway tread Late handrails with U-bolt caps and narrow rear most stanchion on long side rails Wide profile end handrails Sand box clean out door with knuckle buster latch Front nose headlight Front straight grab irons mounted directly to the nose Front right side mounted narrow nose drop grab iron Right nose door with window Front high-mounted (cab) numberboard housings Dual cab side blue flag holder Left side under cab front access bolted X panel; rear door with square corrugated grille Late cab with barrel bolt latches on subbase doors Detailed cab interior with separate floor, rear wall, seats, and control stand In cab grade crossing camera mounted on right side Tinted cab side windows Tall mirror mounted in front of sliding cab side windows on both sides Switching mirror mounted between rear of sliding cab side windows and fixed rear window on engineer’s side Cab roof GE communications handler octagonal dome and dual long STI-CO PTC Dual Track Antenna System without Radome covers See-through dynamic brake exhaust Left side dynamic brake cab: tri blower dynamic brake with flush exhaust Etched metal see-through dynamic brake intake grilles with blower motors visible inside Right side dynamic brake cab: door with grille, small grille, door with grille, and door with grille Dynamic brake cab door with high door handle and high mounted door handle bumper Long right side air intake grille Left side auxiliary cab: 3 tall doors with latches on the #2 door and no auxiliary cab filter box door Right side auxiliary cab: raised X panel door; 3 doors with latches on #2 and #3 doors ES44 style engine cab doors: latched first door in each set of three Three engine cab roof lift rings Left side exhaust cab doors: latched last door in set of three Flush heat exchanger housing with single piece narrow slot grille Late raised radiator grille 22 individually applied etched metal see-through radiator intake and exhaust grilles on sides and top of radiator compartment Left side radiator cab grille arrangement: Raised doors. Grilles - tall-short-tall-short-tall, no grille under brake wheel short front angled grille and two-piece rear angled grille Right side radiator cab grille arrangement: Raised doors. Grilles – tall, short, tall, short, short, tall, short, tall, short front angled grill, two-piece rear angled grille Flat water fill box with sight glass High mounted horizontal rear headlight Rear narrow-spaced dual dummy Multiple Unit (MU) receptacles Accurately profiled frame with separately applied plumbing and cabling Late GE steerable trucks with separately applied brake cylinders, air plumbing, rotating bearing caps, and reinforcement bar under center journal Rust-color painted wheelsets Square handbrake chain bracket Toilet drain with exterior handle AEI tag mounted to right sidesill under rear battery box door Dual Graham-White (Prime) finned 075 air filters Graham-White 994-500 air dryer 5,300-gallon fuel tank with internal waste retention tank, digital fuel gauge, vertical fuel gauge, and round fuel gauge Dual fuel fills per side with rear fill “blanked” Flat top left side fuel tank top box Long crankcase drainpipe attached to the end of the fuel tank Low snowplow without MU doors Factory-applied wire grab irons, snowplow with grab irons, spare knuckles, trainline hoses with silver gladhands, 3-hose MU clusters with silver gladhands, uncoupling levers, windshield wipers, mirrors, sunshades, air tanks, fuel tank mounted electronic bell, brake wheel, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED headlights Printing and lettering legible under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum Radius: 18” Recommended Radius: 22” DCC & sound ready locomotives also feature: Operate using DC DCC ready with 21-pin connector ** In DC operation, both front ditch lights illuminate; rear ditch lights (if equipped) do not illuminate *** Compatible with appropriately programmed ESU decoders while operating using DCC
Produktgewicht inkl. Verpackung: 1,320 kgNeuerscheinung! Auslieferung Dezember 2024
Vorbestellfrist für garantierte Lieferung: 26.02.2024
Road Number Specific ScaleTrains New paint schemes Era: 2023 to present Road number 1827 Special Baltimore and Ohio Heritage scheme Series 3000 to 3064; built 4-6:2012 Formerly CSX 3059 Inverter Cabinet with Bolted and hinged access door, Front Top X Panel Wider Than Rear X Panel, three lower X panels with 4 - 6 - 4 Bolt Pattern Lower X Panels Lost wax brass cast Nathan K5HLR2 Horn w/"Shower Caps" horn mounted on engine cab roof Retrofitted late ET44 style exhaust stack, no flange or center support on stack Fully-assembled LED-illuminated ground lights on both sides of locomotive* LED-illuminated front, rear and rectangle side walkway lights* LED-illuminated front deck-mounted alternating ditch lights** Printed and LED-illuminated lighted number boards* LSL (Locomotive Speed Limiter) indicator lights on cab sides (non-operating) Sill-mounted tow chain Semi-scale coupler buffers equipped with die-cast metal semi-scale SBE bottom shelf knuckle couplers Inside loop uncoupling levers with up down brackets Single trainline hose with silver gladhand Pilot-mounted battery charging receptacles Front dummy Multiple Unit (MU) receptacles mounted to pilot face Front and rear raised pilot-mounted Multiple Unit (MU) receptacles Front and rear single ECP brake equipment box and cable mounted on pilot face See-through round-hole stepwell steps Walkway with front anticlimber; no support brackets GE “nub” pattern walkway tread Late handrails with U-bolt caps and narrow rear most stanchion on long side rails Wide profile end handrails Sand box clean out door with knuckle buster latch Front nose headlight Front straight grab irons mounted directly to the nose Front right side mounted narrow nose drop grab iron Right nose door with window Front high-mounted (cab) numberboard housings Dual cab side blue flag holder Left side under cab front access bolted X panel; rear door with square corrugated grille Late cab with barrel bolt latches on subbase doors Detailed cab interior with separate floor, rear wall, seats, and control stand In cab grade crossing camera mounted on right side Tinted cab side windows Tall mirror mounted in front of sliding cab side windows on both sides Switching mirror mounted between rear of sliding cab side windows and fixed rear window on engineer’s side Cab roof GE communications handler octagonal dome and dual long STI-CO PTC Dual Track Antenna System without Radome covers See-through dynamic brake exhaust Left side dynamic brake cab: tri blower dynamic brake with flush exhaust Etched metal see-through dynamic brake intake grilles with blower motors visible inside Right side dynamic brake cab: door with grille, small grille, door with grille, and door with grille Dynamic brake cab door with high door handle and high mounted door handle bumper Long right side air intake grille Left side auxiliary cab: 3 tall doors with latches on the #2 door and no auxiliary cab filter box door Right side auxiliary cab: raised X panel door; 3 doors with latches on #2 and #3 doors ES44 style engine cab doors: latched first door in each set of three Three engine cab roof lift rings Left side exhaust cab doors: latched last door in set of three Flush heat exchanger housing with single piece narrow slot grille Late raised radiator grille 22 individually applied etched metal see-through radiator intake and exhaust grilles on sides and top of radiator compartment Left side radiator cab grille arrangement: Raised doors. Grilles - tall-short-tall-short-tall, no grille under brake wheel short front angled grille and two-piece rear angled grille Right side radiator cab grille arrangement: Raised doors. Grilles – tall, short, tall, short, short, tall, short, tall, short front angled grill, two-piece rear angled grille Flat water fill box with sight glass High mounted horizontal rear headlight Rear narrow-spaced dual dummy Multiple Unit (MU) receptacles Accurately profiled frame with separately applied plumbing and cabling Late GE steerable trucks with separately applied brake cylinders, air plumbing, rotating bearing caps, and reinforcement bar under center journal Rust-color painted wheelsets Square handbrake chain bracket Toilet drain with exterior handle AEI tag mounted to right sidesill under rear battery box door Dual Graham-White (Prime) finned 075 air filters Graham-White 994-500 air dryer 5,300-gallon fuel tank with internal waste retention tank, digital fuel gauge, vertical fuel gauge, and round fuel gauge Dual fuel fills per side with rear fill “blanked” Flat top left side fuel tank top box Long crankcase drainpipe attached to the end of the fuel tank Low snowplow without MU doors Factory-applied wire grab irons, snowplow with grab irons, spare knuckles, trainline hoses with silver gladhands, 3-hose MU clusters with silver gladhands, uncoupling levers, windshield wipers, mirrors, sunshades, air tanks, fuel tank mounted electronic bell, brake wheel, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED headlights Printing and lettering legible under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum Radius: 18” Recommended Radius: 22” DCC & sound ready locomotives also feature: Operate using DC DCC ready with 21-pin connector ** In DC operation, both front ditch lights illuminate; rear ditch lights (if equipped) do not illuminate *** Compatible with appropriately programmed ESU decoders while operating using DCC
Produktgewicht inkl. Verpackung: 1,320 kgNeuerscheinung! Auslieferung Dezember 2024
Vorbestellfrist für garantierte Lieferung: 26.02.2024
Road Number Specific ScaleTrains New paint schemes Era: 2023 to present Road number 1827 Special Baltimore and Ohio Heritage scheme Series 3000 to 3064; built 4-6:2012 Formerly CSX 3059 Inverter Cabinet with Bolted and hinged access door, Front Top X Panel Wider Than Rear X Panel, three lower X panels with 4 - 6 - 4 Bolt Pattern Lower X Panels Lost wax brass cast Nathan K5HLR2 Horn w/"Shower Caps" horn mounted on engine cab roof Retrofitted late ET44 style exhaust stack, no flange or center support on stack Fully-assembled LED-illuminated ground lights on both sides of locomotive* LED-illuminated front, rear and rectangle side walkway lights* LED-illuminated front deck-mounted alternating ditch lights** Printed and LED-illuminated lighted number boards* LSL (Locomotive Speed Limiter) indicator lights on cab sides (non-operating) Sill-mounted tow chain Semi-scale coupler buffers equipped with die-cast metal semi-scale SBE bottom shelf knuckle couplers Inside loop uncoupling levers with up down brackets Single trainline hose with silver gladhand Pilot-mounted battery charging receptacles Front dummy Multiple Unit (MU) receptacles mounted to pilot face Front and rear raised pilot-mounted Multiple Unit (MU) receptacles Front and rear single ECP brake equipment box and cable mounted on pilot face See-through round-hole stepwell steps Walkway with front anticlimber; no support brackets GE “nub” pattern walkway tread Late handrails with U-bolt caps and narrow rear most stanchion on long side rails Wide profile end handrails Sand box clean out door with knuckle buster latch Front nose headlight Front straight grab irons mounted directly to the nose Front right side mounted narrow nose drop grab iron Right nose door with window Front high-mounted (cab) numberboard housings Dual cab side blue flag holder Left side under cab front access bolted X panel; rear door with square corrugated grille Late cab with barrel bolt latches on subbase doors Detailed cab interior with separate floor, rear wall, seats, and control stand In cab grade crossing camera mounted on right side Tinted cab side windows Tall mirror mounted in front of sliding cab side windows on both sides Switching mirror mounted between rear of sliding cab side windows and fixed rear window on engineer’s side Cab roof GE communications handler octagonal dome and dual long STI-CO PTC Dual Track Antenna System without Radome covers See-through dynamic brake exhaust Left side dynamic brake cab: tri blower dynamic brake with flush exhaust Etched metal see-through dynamic brake intake grilles with blower motors visible inside Right side dynamic brake cab: door with grille, small grille, door with grille, and door with grille Dynamic brake cab door with high door handle and high mounted door handle bumper Long right side air intake grille Left side auxiliary cab: 3 tall doors with latches on the #2 door and no auxiliary cab filter box door Right side auxiliary cab: raised X panel door; 3 doors with latches on #2 and #3 doors ES44 style engine cab doors: latched first door in each set of three Three engine cab roof lift rings Left side exhaust cab doors: latched last door in set of three Flush heat exchanger housing with single piece narrow slot grille Late raised radiator grille 22 individually applied etched metal see-through radiator intake and exhaust grilles on sides and top of radiator compartment Left side radiator cab grille arrangement: Raised doors. Grilles - tall-short-tall-short-tall, no grille under brake wheel short front angled grille and two-piece rear angled grille Right side radiator cab grille arrangement: Raised doors. Grilles – tall, short, tall, short, short, tall, short, tall, short front angled grill, two-piece rear angled grille Flat water fill box with sight glass High mounted horizontal rear headlight Rear narrow-spaced dual dummy Multiple Unit (MU) receptacles Accurately profiled frame with separately applied plumbing and cabling Late GE steerable trucks with separately applied brake cylinders, air plumbing, rotating bearing caps, and reinforcement bar under center journal Rust-color painted wheelsets Square handbrake chain bracket Toilet drain with exterior handle AEI tag mounted to right sidesill under rear battery box door Dual Graham-White (Prime) finned 075 air filters Graham-White 994-500 air dryer 5,300-gallon fuel tank with internal waste retention tank, digital fuel gauge, vertical fuel gauge, and round fuel gauge Dual fuel fills per side with rear fill “blanked” Flat top left side fuel tank top box Long crankcase drainpipe attached to the end of the fuel tank Low snowplow without MU doors Factory-applied wire grab irons, snowplow with grab irons, spare knuckles, trainline hoses with silver gladhands, 3-hose MU clusters with silver gladhands, uncoupling levers, windshield wipers, mirrors, sunshades, air tanks, fuel tank mounted electronic bell, brake wheel, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED headlights Printing and lettering legible under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum Radius: 18” Recommended Radius: 22” ESU-LokSound 5 DCC and Sound decoder with “Full Throttle” Two (2) cube-type speakers Accurate GEVO-12 prime mover and auxiliary sounds, horn, bell, and more ESU-designed PowerPack with two (2) super capacitors*** Operates on both DC and DCC layouts
Produktgewicht inkl. Verpackung: 1,320 kgNeuerscheinung! Auslieferung Dezember 2024
Vorbestellfrist für garantierte Lieferung: 26.02.2024
Road Number-Specific ScaleTrains All-new model Era: 1980s – 1990s Series C&NW 5500-5537; ex-NYC 3010-3049, built Nov/Dec 1965 C&NW 5500 Lost-wax cast brass Leslie S-3-LR horn mounted on number board housing Standard “whip” communications antenna base mounted to cab roof Front EMD low plow with MU hose doors Replacement bearing pedestal liners White corner step edges and kickplates “OY” Scheme, “C&NW System” logo C&NW 5504 Lost-wax cast brass Leslie SU-3L-LR horn mounted on number board housing Excalibur low-profile “ice skate” communications antenna mounted to cab roof Front EMD medium plow without MU hose doors Green air reservoirs White corner step edges and yellow kickplates “OY” Scheme, “C&NW System” logo C&NW 5520 Lost-wax cast brass Leslie SU-3L-LR horn mounted on number board housing Excalibur low-profile “ice skate” communications antenna mounted to cab roof Front EMD medium plow without MU hose doors Yellow-painted nose bell White corner step edges and kickplates “OY” Scheme, “C&NW System” logo Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-Illuminated rectangular walkway lights mounted between front and rear sanding valve doors, and round walkway light aft of raised walkway duct* LED-illuminated tri-color, flush-mounted front and rear class lights with raised gaskets LED-illuminated Tomar 804-1274 Strobe* Printed number boards with separately-controlled, backlit LED-illumination* 3-hose multiple unit (MU) hose groups with mounting bracket and gladhand detail Semi-scale coupler buffers equipped with durable metal semi-scale Type E knuckle couplers Front and rear straight uncoupling levers with straight rod extensions Notched-corner pilot face with square access plate, front and rear “Early” angled deck-mounted multiple unit (MU) receptacles, dual per end, front and rear “Short” stepwells with nub-bottom pilots, front and rear End handrails with deck and pilot face-mounted stanchions, front and rear Front and rear early small deck extension Positionable tapered (early) drop steps, front and rear Early treadplate 81” low short hood with ratchet handbrake Early straight grabs and “flipped” nut-bolt-washer (NBW) mounting on nose front and top Latched battery box doors with narrow louvers and tab-style (early) hinges Early cab sub-base doors without reinforcement ribs, both sides Single right rear cab step Cab Sub-Base Step Guards Early cab step guards (long taper) No hopper water piping underneath front battery box step Standard EMD high headlight with glare visors in numberboard housing “35-Line” cab with standard front windshields, and standard armrests, both sides Detailed cab interior with separate floor, cab blowers, rear wall, late seats with armrests, and standard AAR control stand Positionable cab side windows “Salem” combination mirror & windshield wing mounted ahead of the cab side windows, both sides Standard EMD sunshades with long mounting tracks Long hood with standard electrical cabinet seam, bolted generator compartment door, and early inertial drain hole placement (wide spacing on engineer’s side, low on fireman’s side) Small ECAFB Early (smooth) blower duct housing Early long handrail stanchion spacing with “short” stanchions at thin section of sidesill Early inertial air intake grilles without drip rails Standard turbo exhaust stack Early extended-range dynamic brake housing (short tapers), with retrofitted long contactor door See-through 48” standard-height dynamic brake fan housing with 10-blade fan and hub assembly, with spiral-grill and center cap Dynamic brake intakes with see-through intake vanes, and resistor grid detail inside of the housing Diamond-mesh radiator intake screening See-through standard-height 48” radiator fan housings with 8-blade fan and hub assembly Separately-applied radiator core detail mounted inside of long hood, visible under radiator fans Curved radiator fan grab iron Rear LED-illuminated horizontal headlight and standard housing Early rear sander door catch placement (inboard) Underbody frame rails with separately-applied plumbing and traction motor cable bundle details Detailed Blomberg-B truck frames (LFM-cast) with Hyatt bearing housings, separately-applied brake cylinders in released (piston retracted) position, elliptical springs, end transom detail, separate sanding lines and brackets, deleted outer brake shoes, and separate swing hanger detail Separately-applied flexible neoprene sanding lines at stepwell ends of trucks Rust-color painted wheelsets “Aeroquip” brand speed recorder with adapter flange mounted to right #2 axle ATC Pickup shoe on #1 axle, right side Standard 4 jacking pads Frame-mounted bell Salem-brand #824-170 and #818-170 primary and secondary centrifugal air filters, respectively (accordion-style) Separately-applied brake vent regulator valve and plumbing detail on underbody 3600-gallon fuel tank with early mounting brackets, inset dial gauge on right side, and early rear drain bar Separately-applied fuel fillers, drains, and breather piping on fuel tanks Separately-applied engine oil sump drain fitting with hose Separately-applied radiator water drain fitting on underbody Separately-applied truck air line plumbing on underbody above each truck, both sides Separately-applied wireform grab irons, wireform lift rings, etched windshield wipers, trainline hoses, sand hatch covers, and more Motor with 5-pole skew-wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Paint colors match Tru-Color Paint color: TCP-109 C&NW Green TCP-353 C&NW Early Yellow Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended Radius: 22” DCC & sound-equipped locomotives also feature: ESU LokSound 5 DCC & Sound decoder with “Full Throttle” functions Two (2) cube-type speakers Turbocharged EMD 16-645 prime mover sounds ESU designed “PowerPack” with two super capacitors**** Operates on both DC and DCC layouts
Produktgewicht inkl. Verpackung: 1,320 kgNeuerscheinung! Auslieferung Dezember 2024
Vorbestellfrist für garantierte Lieferung: 26.02.2024
Road Number-Specific ScaleTrains All-new model Era: 1980s – 1990s Series C&NW 5500-5537; ex-NYC 3010-3049, built Nov/Dec 1965 C&NW 5500 Lost-wax cast brass Leslie S-3-LR horn mounted on number board housing Standard “whip” communications antenna base mounted to cab roof Front EMD low plow with MU hose doors Replacement bearing pedestal liners White corner step edges and kickplates “OY” Scheme, “C&NW System” logo C&NW 5504 Lost-wax cast brass Leslie SU-3L-LR horn mounted on number board housing Excalibur low-profile “ice skate” communications antenna mounted to cab roof Front EMD medium plow without MU hose doors Green air reservoirs White corner step edges and yellow kickplates “OY” Scheme, “C&NW System” logo C&NW 5520 Lost-wax cast brass Leslie SU-3L-LR horn mounted on number board housing Excalibur low-profile “ice skate” communications antenna mounted to cab roof Front EMD medium plow without MU hose doors Yellow-painted nose bell White corner step edges and kickplates “OY” Scheme, “C&NW System” logo Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-Illuminated rectangular walkway lights mounted between front and rear sanding valve doors, and round walkway light aft of raised walkway duct* LED-illuminated tri-color, flush-mounted front and rear class lights with raised gaskets LED-illuminated Tomar 804-1274 Strobe* Printed number boards with separately-controlled, backlit LED-illumination* 3-hose multiple unit (MU) hose groups with mounting bracket and gladhand detail Semi-scale coupler buffers equipped with durable metal semi-scale Type E knuckle couplers Front and rear straight uncoupling levers with straight rod extensions Notched-corner pilot face with square access plate, front and rear “Early” angled deck-mounted multiple unit (MU) receptacles, dual per end, front and rear “Short” stepwells with nub-bottom pilots, front and rear End handrails with deck and pilot face-mounted stanchions, front and rear Front and rear early small deck extension Positionable tapered (early) drop steps, front and rear Early treadplate 81” low short hood with ratchet handbrake Early straight grabs and “flipped” nut-bolt-washer (NBW) mounting on nose front and top Latched battery box doors with narrow louvers and tab-style (early) hinges Early cab sub-base doors without reinforcement ribs, both sides Single right rear cab step Cab Sub-Base Step Guards Early cab step guards (long taper) No hopper water piping underneath front battery box step Standard EMD high headlight with glare visors in numberboard housing “35-Line” cab with standard front windshields, and standard armrests, both sides Detailed cab interior with separate floor, cab blowers, rear wall, late seats with armrests, and standard AAR control stand Positionable cab side windows “Salem” combination mirror & windshield wing mounted ahead of the cab side windows, both sides Standard EMD sunshades with long mounting tracks Long hood with standard electrical cabinet seam, bolted generator compartment door, and early inertial drain hole placement (wide spacing on engineer’s side, low on fireman’s side) Small ECAFB Early (smooth) blower duct housing Early long handrail stanchion spacing with “short” stanchions at thin section of sidesill Early inertial air intake grilles without drip rails Standard turbo exhaust stack Early extended-range dynamic brake housing (short tapers), with retrofitted long contactor door See-through 48” standard-height dynamic brake fan housing with 10-blade fan and hub assembly, with spiral-grill and center cap Dynamic brake intakes with see-through intake vanes, and resistor grid detail inside of the housing Diamond-mesh radiator intake screening See-through standard-height 48” radiator fan housings with 8-blade fan and hub assembly Separately-applied radiator core detail mounted inside of long hood, visible under radiator fans Curved radiator fan grab iron Rear LED-illuminated horizontal headlight and standard housing Early rear sander door catch placement (inboard) Underbody frame rails with separately-applied plumbing and traction motor cable bundle details Detailed Blomberg-B truck frames (LFM-cast) with Hyatt bearing housings, separately-applied brake cylinders in released (piston retracted) position, elliptical springs, end transom detail, separate sanding lines and brackets, deleted outer brake shoes, and separate swing hanger detail Separately-applied flexible neoprene sanding lines at stepwell ends of trucks Rust-color painted wheelsets “Aeroquip” brand speed recorder with adapter flange mounted to right #2 axle ATC Pickup shoe on #1 axle, right side Standard 4 jacking pads Frame-mounted bell Salem-brand #824-170 and #818-170 primary and secondary centrifugal air filters, respectively (accordion-style) Separately-applied brake vent regulator valve and plumbing detail on underbody 3600-gallon fuel tank with early mounting brackets, inset dial gauge on right side, and early rear drain bar Separately-applied fuel fillers, drains, and breather piping on fuel tanks Separately-applied engine oil sump drain fitting with hose Separately-applied radiator water drain fitting on underbody Separately-applied truck air line plumbing on underbody above each truck, both sides Separately-applied wireform grab irons, wireform lift rings, etched windshield wipers, trainline hoses, sand hatch covers, and more Motor with 5-pole skew-wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Paint colors match Tru-Color Paint color: TCP-109 C&NW Green TCP-353 C&NW Early Yellow Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended Radius: 22” DCC & sound-equipped locomotives also feature: ESU LokSound 5 DCC & Sound decoder with “Full Throttle” functions Two (2) cube-type speakers Turbocharged EMD 16-645 prime mover sounds ESU designed “PowerPack” with two super capacitors**** Operates on both DC and DCC layouts
Produktgewicht inkl. Verpackung: 1,320 kgNeuerscheinung! Auslieferung Dezember 2024
Vorbestellfrist für garantierte Lieferung: 26.02.2024
Road Number-Specific ScaleTrains All-new model Era: 1980s – 1990s Series C&NW 5500-5537; ex-NYC 3010-3049, built Nov/Dec 1965 C&NW 5500 Lost-wax cast brass Leslie S-3-LR horn mounted on number board housing Standard “whip” communications antenna base mounted to cab roof Front EMD low plow with MU hose doors Replacement bearing pedestal liners White corner step edges and kickplates “OY” Scheme, “C&NW System” logo C&NW 5504 Lost-wax cast brass Leslie SU-3L-LR horn mounted on number board housing Excalibur low-profile “ice skate” communications antenna mounted to cab roof Front EMD medium plow without MU hose doors Green air reservoirs White corner step edges and yellow kickplates “OY” Scheme, “C&NW System” logo C&NW 5520 Lost-wax cast brass Leslie SU-3L-LR horn mounted on number board housing Excalibur low-profile “ice skate” communications antenna mounted to cab roof Front EMD medium plow without MU hose doors Yellow-painted nose bell White corner step edges and kickplates “OY” Scheme, “C&NW System” logo Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-Illuminated rectangular walkway lights mounted between front and rear sanding valve doors, and round walkway light aft of raised walkway duct* LED-illuminated tri-color, flush-mounted front and rear class lights with raised gaskets LED-illuminated Tomar 804-1274 Strobe* Printed number boards with separately-controlled, backlit LED-illumination* 3-hose multiple unit (MU) hose groups with mounting bracket and gladhand detail Semi-scale coupler buffers equipped with durable metal semi-scale Type E knuckle couplers Front and rear straight uncoupling levers with straight rod extensions Notched-corner pilot face with square access plate, front and rear “Early” angled deck-mounted multiple unit (MU) receptacles, dual per end, front and rear “Short” stepwells with nub-bottom pilots, front and rear End handrails with deck and pilot face-mounted stanchions, front and rear Front and rear early small deck extension Positionable tapered (early) drop steps, front and rear Early treadplate 81” low short hood with ratchet handbrake Early straight grabs and “flipped” nut-bolt-washer (NBW) mounting on nose front and top Latched battery box doors with narrow louvers and tab-style (early) hinges Early cab sub-base doors without reinforcement ribs, both sides Single right rear cab step Cab Sub-Base Step Guards Early cab step guards (long taper) No hopper water piping underneath front battery box step Standard EMD high headlight with glare visors in numberboard housing “35-Line” cab with standard front windshields, and standard armrests, both sides Detailed cab interior with separate floor, cab blowers, rear wall, late seats with armrests, and standard AAR control stand Positionable cab side windows “Salem” combination mirror & windshield wing mounted ahead of the cab side windows, both sides Standard EMD sunshades with long mounting tracks Long hood with standard electrical cabinet seam, bolted generator compartment door, and early inertial drain hole placement (wide spacing on engineer’s side, low on fireman’s side) Small ECAFB Early (smooth) blower duct housing Early long handrail stanchion spacing with “short” stanchions at thin section of sidesill Early inertial air intake grilles without drip rails Standard turbo exhaust stack Early extended-range dynamic brake housing (short tapers), with retrofitted long contactor door See-through 48” standard-height dynamic brake fan housing with 10-blade fan and hub assembly, with spiral-grill and center cap Dynamic brake intakes with see-through intake vanes, and resistor grid detail inside of the housing Diamond-mesh radiator intake screening See-through standard-height 48” radiator fan housings with 8-blade fan and hub assembly Separately-applied radiator core detail mounted inside of long hood, visible under radiator fans Curved radiator fan grab iron Rear LED-illuminated horizontal headlight and standard housing Early rear sander door catch placement (inboard) Underbody frame rails with separately-applied plumbing and traction motor cable bundle details Detailed Blomberg-B truck frames (LFM-cast) with Hyatt bearing housings, separately-applied brake cylinders in released (piston retracted) position, elliptical springs, end transom detail, separate sanding lines and brackets, deleted outer brake shoes, and separate swing hanger detail Separately-applied flexible neoprene sanding lines at stepwell ends of trucks Rust-color painted wheelsets “Aeroquip” brand speed recorder with adapter flange mounted to right #2 axle ATC Pickup shoe on #1 axle, right side Standard 4 jacking pads Frame-mounted bell Salem-brand #824-170 and #818-170 primary and secondary centrifugal air filters, respectively (accordion-style) Separately-applied brake vent regulator valve and plumbing detail on underbody 3600-gallon fuel tank with early mounting brackets, inset dial gauge on right side, and early rear drain bar Separately-applied fuel fillers, drains, and breather piping on fuel tanks Separately-applied engine oil sump drain fitting with hose Separately-applied radiator water drain fitting on underbody Separately-applied truck air line plumbing on underbody above each truck, both sides Separately-applied wireform grab irons, wireform lift rings, etched windshield wipers, trainline hoses, sand hatch covers, and more Motor with 5-pole skew-wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Paint colors match Tru-Color Paint color: TCP-109 C&NW Green TCP-353 C&NW Early Yellow Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended Radius: 22” DCC & sound-equipped locomotives also feature: ESU LokSound 5 DCC & Sound decoder with “Full Throttle” functions Two (2) cube-type speakers Turbocharged EMD 16-645 prime mover sounds ESU designed “PowerPack” with two super capacitors**** Operates on both DC and DCC layouts
Produktgewicht inkl. Verpackung: 1,320 kgNeuerscheinung! Auslieferung Dezember 2024
Vorbestellfrist für garantierte Lieferung: 26.02.2024
Road Number-Specific ScaleTrains All-new model Era: 1980s – 1990s Series C&NW 5500-5537; ex-NYC 3010-3049, built Nov/Dec 1965 C&NW 5500 Lost-wax cast brass Leslie S-3-LR horn mounted on number board housing Standard “whip” communications antenna base mounted to cab roof Front EMD low plow with MU hose doors Replacement bearing pedestal liners White corner step edges and kickplates “OY” Scheme, “C&NW System” logo C&NW 5504 Lost-wax cast brass Leslie SU-3L-LR horn mounted on number board housing Excalibur low-profile “ice skate” communications antenna mounted to cab roof Front EMD medium plow without MU hose doors Green air reservoirs White corner step edges and yellow kickplates “OY” Scheme, “C&NW System” logo C&NW 5520 Lost-wax cast brass Leslie SU-3L-LR horn mounted on number board housing Excalibur low-profile “ice skate” communications antenna mounted to cab roof Front EMD medium plow without MU hose doors Yellow-painted nose bell White corner step edges and kickplates “OY” Scheme, “C&NW System” logo Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-Illuminated rectangular walkway lights mounted between front and rear sanding valve doors, and round walkway light aft of raised walkway duct* LED-illuminated tri-color, flush-mounted front and rear class lights with raised gaskets LED-illuminated Tomar 804-1274 Strobe* Printed number boards with separately-controlled, backlit LED-illumination* 3-hose multiple unit (MU) hose groups with mounting bracket and gladhand detail Semi-scale coupler buffers equipped with durable metal semi-scale Type E knuckle couplers Front and rear straight uncoupling levers with straight rod extensions Notched-corner pilot face with square access plate, front and rear “Early” angled deck-mounted multiple unit (MU) receptacles, dual per end, front and rear “Short” stepwells with nub-bottom pilots, front and rear End handrails with deck and pilot face-mounted stanchions, front and rear Front and rear early small deck extension Positionable tapered (early) drop steps, front and rear Early treadplate 81” low short hood with ratchet handbrake Early straight grabs and “flipped” nut-bolt-washer (NBW) mounting on nose front and top Latched battery box doors with narrow louvers and tab-style (early) hinges Early cab sub-base doors without reinforcement ribs, both sides Single right rear cab step Cab Sub-Base Step Guards Early cab step guards (long taper) No hopper water piping underneath front battery box step Standard EMD high headlight with glare visors in numberboard housing “35-Line” cab with standard front windshields, and standard armrests, both sides Detailed cab interior with separate floor, cab blowers, rear wall, late seats with armrests, and standard AAR control stand Positionable cab side windows “Salem” combination mirror & windshield wing mounted ahead of the cab side windows, both sides Standard EMD sunshades with long mounting tracks Long hood with standard electrical cabinet seam, bolted generator compartment door, and early inertial drain hole placement (wide spacing on engineer’s side, low on fireman’s side) Small ECAFB Early (smooth) blower duct housing Early long handrail stanchion spacing with “short” stanchions at thin section of sidesill Early inertial air intake grilles without drip rails Standard turbo exhaust stack Early extended-range dynamic brake housing (short tapers), with retrofitted long contactor door See-through 48” standard-height dynamic brake fan housing with 10-blade fan and hub assembly, with spiral-grill and center cap Dynamic brake intakes with see-through intake vanes, and resistor grid detail inside of the housing Diamond-mesh radiator intake screening See-through standard-height 48” radiator fan housings with 8-blade fan and hub assembly Separately-applied radiator core detail mounted inside of long hood, visible under radiator fans Curved radiator fan grab iron Rear LED-illuminated horizontal headlight and standard housing Early rear sander door catch placement (inboard) Underbody frame rails with separately-applied plumbing and traction motor cable bundle details Detailed Blomberg-B truck frames (LFM-cast) with Hyatt bearing housings, separately-applied brake cylinders in released (piston retracted) position, elliptical springs, end transom detail, separate sanding lines and brackets, deleted outer brake shoes, and separate swing hanger detail Separately-applied flexible neoprene sanding lines at stepwell ends of trucks Rust-color painted wheelsets “Aeroquip” brand speed recorder with adapter flange mounted to right #2 axle ATC Pickup shoe on #1 axle, right side Standard 4 jacking pads Frame-mounted bell Salem-brand #824-170 and #818-170 primary and secondary centrifugal air filters, respectively (accordion-style) Separately-applied brake vent regulator valve and plumbing detail on underbody 3600-gallon fuel tank with early mounting brackets, inset dial gauge on right side, and early rear drain bar Separately-applied fuel fillers, drains, and breather piping on fuel tanks Separately-applied engine oil sump drain fitting with hose Separately-applied radiator water drain fitting on underbody Separately-applied truck air line plumbing on underbody above each truck, both sides Separately-applied wireform grab irons, wireform lift rings, etched windshield wipers, trainline hoses, sand hatch covers, and more Motor with 5-pole skew-wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Paint colors match Tru-Color Paint color: TCP-109 C&NW Green TCP-353 C&NW Early Yellow Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended Radius: 22” DCC & sound-equipped locomotives also feature: DC/DCC & sound ready locomotives also feature: Operates on DC layouts DCC-ready with 21-pin connector
Produktgewicht inkl. Verpackung: 1,320 kgNeuerscheinung! Auslieferung Dezember 2024
Vorbestellfrist für garantierte Lieferung: 26.02.2024
Road Number-Specific ScaleTrains All-new model Era: 1980s – 1990s Series C&NW 5500-5537; ex-NYC 3010-3049, built Nov/Dec 1965 C&NW 5500 Lost-wax cast brass Leslie S-3-LR horn mounted on number board housing Standard “whip” communications antenna base mounted to cab roof Front EMD low plow with MU hose doors Replacement bearing pedestal liners White corner step edges and kickplates “OY” Scheme, “C&NW System” logo C&NW 5504 Lost-wax cast brass Leslie SU-3L-LR horn mounted on number board housing Excalibur low-profile “ice skate” communications antenna mounted to cab roof Front EMD medium plow without MU hose doors Green air reservoirs White corner step edges and yellow kickplates “OY” Scheme, “C&NW System” logo C&NW 5520 Lost-wax cast brass Leslie SU-3L-LR horn mounted on number board housing Excalibur low-profile “ice skate” communications antenna mounted to cab roof Front EMD medium plow without MU hose doors Yellow-painted nose bell White corner step edges and kickplates “OY” Scheme, “C&NW System” logo Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-Illuminated rectangular walkway lights mounted between front and rear sanding valve doors, and round walkway light aft of raised walkway duct* LED-illuminated tri-color, flush-mounted front and rear class lights with raised gaskets LED-illuminated Tomar 804-1274 Strobe* Printed number boards with separately-controlled, backlit LED-illumination* 3-hose multiple unit (MU) hose groups with mounting bracket and gladhand detail Semi-scale coupler buffers equipped with durable metal semi-scale Type E knuckle couplers Front and rear straight uncoupling levers with straight rod extensions Notched-corner pilot face with square access plate, front and rear “Early” angled deck-mounted multiple unit (MU) receptacles, dual per end, front and rear “Short” stepwells with nub-bottom pilots, front and rear End handrails with deck and pilot face-mounted stanchions, front and rear Front and rear early small deck extension Positionable tapered (early) drop steps, front and rear Early treadplate 81” low short hood with ratchet handbrake Early straight grabs and “flipped” nut-bolt-washer (NBW) mounting on nose front and top Latched battery box doors with narrow louvers and tab-style (early) hinges Early cab sub-base doors without reinforcement ribs, both sides Single right rear cab step Cab Sub-Base Step Guards Early cab step guards (long taper) No hopper water piping underneath front battery box step Standard EMD high headlight with glare visors in numberboard housing “35-Line” cab with standard front windshields, and standard armrests, both sides Detailed cab interior with separate floor, cab blowers, rear wall, late seats with armrests, and standard AAR control stand Positionable cab side windows “Salem” combination mirror & windshield wing mounted ahead of the cab side windows, both sides Standard EMD sunshades with long mounting tracks Long hood with standard electrical cabinet seam, bolted generator compartment door, and early inertial drain hole placement (wide spacing on engineer’s side, low on fireman’s side) Small ECAFB Early (smooth) blower duct housing Early long handrail stanchion spacing with “short” stanchions at thin section of sidesill Early inertial air intake grilles without drip rails Standard turbo exhaust stack Early extended-range dynamic brake housing (short tapers), with retrofitted long contactor door See-through 48” standard-height dynamic brake fan housing with 10-blade fan and hub assembly, with spiral-grill and center cap Dynamic brake intakes with see-through intake vanes, and resistor grid detail inside of the housing Diamond-mesh radiator intake screening See-through standard-height 48” radiator fan housings with 8-blade fan and hub assembly Separately-applied radiator core detail mounted inside of long hood, visible under radiator fans Curved radiator fan grab iron Rear LED-illuminated horizontal headlight and standard housing Early rear sander door catch placement (inboard) Underbody frame rails with separately-applied plumbing and traction motor cable bundle details Detailed Blomberg-B truck frames (LFM-cast) with Hyatt bearing housings, separately-applied brake cylinders in released (piston retracted) position, elliptical springs, end transom detail, separate sanding lines and brackets, deleted outer brake shoes, and separate swing hanger detail Separately-applied flexible neoprene sanding lines at stepwell ends of trucks Rust-color painted wheelsets “Aeroquip” brand speed recorder with adapter flange mounted to right #2 axle ATC Pickup shoe on #1 axle, right side Standard 4 jacking pads Frame-mounted bell Salem-brand #824-170 and #818-170 primary and secondary centrifugal air filters, respectively (accordion-style) Separately-applied brake vent regulator valve and plumbing detail on underbody 3600-gallon fuel tank with early mounting brackets, inset dial gauge on right side, and early rear drain bar Separately-applied fuel fillers, drains, and breather piping on fuel tanks Separately-applied engine oil sump drain fitting with hose Separately-applied radiator water drain fitting on underbody Separately-applied truck air line plumbing on underbody above each truck, both sides Separately-applied wireform grab irons, wireform lift rings, etched windshield wipers, trainline hoses, sand hatch covers, and more Motor with 5-pole skew-wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Paint colors match Tru-Color Paint color: TCP-109 C&NW Green TCP-353 C&NW Early Yellow Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended Radius: 22” DCC & sound-equipped locomotives also feature: DC/DCC & sound ready locomotives also feature: Operates on DC layouts DCC-ready with 21-pin connector
Produktgewicht inkl. Verpackung: 1,320 kgNeuerscheinung! Auslieferung Dezember 2024
Vorbestellfrist für garantierte Lieferung: 26.02.2024
Road Number-Specific ScaleTrains All-new model Era: 1980s – 1990s Series C&NW 5500-5537; ex-NYC 3010-3049, built Nov/Dec 1965 C&NW 5500 Lost-wax cast brass Leslie S-3-LR horn mounted on number board housing Standard “whip” communications antenna base mounted to cab roof Front EMD low plow with MU hose doors Replacement bearing pedestal liners White corner step edges and kickplates “OY” Scheme, “C&NW System” logo C&NW 5504 Lost-wax cast brass Leslie SU-3L-LR horn mounted on number board housing Excalibur low-profile “ice skate” communications antenna mounted to cab roof Front EMD medium plow without MU hose doors Green air reservoirs White corner step edges and yellow kickplates “OY” Scheme, “C&NW System” logo C&NW 5520 Lost-wax cast brass Leslie SU-3L-LR horn mounted on number board housing Excalibur low-profile “ice skate” communications antenna mounted to cab roof Front EMD medium plow without MU hose doors Yellow-painted nose bell White corner step edges and kickplates “OY” Scheme, “C&NW System” logo Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-Illuminated rectangular walkway lights mounted between front and rear sanding valve doors, and round walkway light aft of raised walkway duct* LED-illuminated tri-color, flush-mounted front and rear class lights with raised gaskets LED-illuminated Tomar 804-1274 Strobe* Printed number boards with separately-controlled, backlit LED-illumination* 3-hose multiple unit (MU) hose groups with mounting bracket and gladhand detail Semi-scale coupler buffers equipped with durable metal semi-scale Type E knuckle couplers Front and rear straight uncoupling levers with straight rod extensions Notched-corner pilot face with square access plate, front and rear “Early” angled deck-mounted multiple unit (MU) receptacles, dual per end, front and rear “Short” stepwells with nub-bottom pilots, front and rear End handrails with deck and pilot face-mounted stanchions, front and rear Front and rear early small deck extension Positionable tapered (early) drop steps, front and rear Early treadplate 81” low short hood with ratchet handbrake Early straight grabs and “flipped” nut-bolt-washer (NBW) mounting on nose front and top Latched battery box doors with narrow louvers and tab-style (early) hinges Early cab sub-base doors without reinforcement ribs, both sides Single right rear cab step Cab Sub-Base Step Guards Early cab step guards (long taper) No hopper water piping underneath front battery box step Standard EMD high headlight with glare visors in numberboard housing “35-Line” cab with standard front windshields, and standard armrests, both sides Detailed cab interior with separate floor, cab blowers, rear wall, late seats with armrests, and standard AAR control stand Positionable cab side windows “Salem” combination mirror & windshield wing mounted ahead of the cab side windows, both sides Standard EMD sunshades with long mounting tracks Long hood with standard electrical cabinet seam, bolted generator compartment door, and early inertial drain hole placement (wide spacing on engineer’s side, low on fireman’s side) Small ECAFB Early (smooth) blower duct housing Early long handrail stanchion spacing with “short” stanchions at thin section of sidesill Early inertial air intake grilles without drip rails Standard turbo exhaust stack Early extended-range dynamic brake housing (short tapers), with retrofitted long contactor door See-through 48” standard-height dynamic brake fan housing with 10-blade fan and hub assembly, with spiral-grill and center cap Dynamic brake intakes with see-through intake vanes, and resistor grid detail inside of the housing Diamond-mesh radiator intake screening See-through standard-height 48” radiator fan housings with 8-blade fan and hub assembly Separately-applied radiator core detail mounted inside of long hood, visible under radiator fans Curved radiator fan grab iron Rear LED-illuminated horizontal headlight and standard housing Early rear sander door catch placement (inboard) Underbody frame rails with separately-applied plumbing and traction motor cable bundle details Detailed Blomberg-B truck frames (LFM-cast) with Hyatt bearing housings, separately-applied brake cylinders in released (piston retracted) position, elliptical springs, end transom detail, separate sanding lines and brackets, deleted outer brake shoes, and separate swing hanger detail Separately-applied flexible neoprene sanding lines at stepwell ends of trucks Rust-color painted wheelsets “Aeroquip” brand speed recorder with adapter flange mounted to right #2 axle ATC Pickup shoe on #1 axle, right side Standard 4 jacking pads Frame-mounted bell Salem-brand #824-170 and #818-170 primary and secondary centrifugal air filters, respectively (accordion-style) Separately-applied brake vent regulator valve and plumbing detail on underbody 3600-gallon fuel tank with early mounting brackets, inset dial gauge on right side, and early rear drain bar Separately-applied fuel fillers, drains, and breather piping on fuel tanks Separately-applied engine oil sump drain fitting with hose Separately-applied radiator water drain fitting on underbody Separately-applied truck air line plumbing on underbody above each truck, both sides Separately-applied wireform grab irons, wireform lift rings, etched windshield wipers, trainline hoses, sand hatch covers, and more Motor with 5-pole skew-wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Paint colors match Tru-Color Paint color: TCP-109 C&NW Green TCP-353 C&NW Early Yellow Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended Radius: 22” DCC & sound-equipped locomotives also feature: DC/DCC & sound ready locomotives also feature: Operates on DC layouts DCC-ready with 21-pin connector
Produktgewicht inkl. Verpackung: 1,320 kgNeuerscheinung! Auslieferung Dezember 2024
Vorbestellfrist für garantierte Lieferung: 26.02.2024
Road Number-Specific ScaleTrains All-new model Era: 1980s – 1990s Series C&NW 5500-5537; ex-NYC 3010-3049, built Nov/Dec 1965 C&NW 5505 Lost-wax cast brass Leslie S-3-LR horn mounted on number board housing Excalibur low-profile “ice skate” communications antenna mounted to cab roof Front EMD low plow with MU hose doors White corner step edges and kickplates “OY” Scheme, “Employee Owned” logo C&NW 5506 Lost-wax cast brass Leslie SU-3L-LR horn mounted on number board housing Excalibur low-profile “ice skate” communications antenna mounted to cab roof Front EMD medium plow without MU hose doors Green walkway duct Green air reservoirs White corner step edges and kickplates “OY” Scheme, “Employee Owned” logo C&NW 5525 Lost-wax cast brass Leslie S-3-LR horn mounted on number board housing Excalibur low-profile “ice skate” communications antenna mounted to cab roof Front EMD medium plow without MU hose doors Green walkway duct Green air reservoirs White corner step edges and kickplates “OY” Scheme, “Employee Owned” logo Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-Illuminated rectangular walkway lights mounted between front and rear sanding valve doors, and round walkway light aft of raised walkway duct* LED-illuminated tri-color, flush-mounted front and rear class lights with raised gaskets LED-illuminated Tomar 804-1274 Strobe* Printed number boards with separately-controlled, backlit LED-illumination* 3-hose multiple unit (MU) hose groups with mounting bracket and gladhand detail Semi-scale coupler buffers equipped with durable metal semi-scale Type E knuckle couplers Front and rear straight uncoupling levers with straight rod extensions Notched-corner pilot face with square access plate, front and rear “Early” angled deck-mounted multiple unit (MU) receptacles, dual per end, front and rear “Short” stepwells with nub-bottom pilots, front and rear End handrails with deck and pilot face-mounted stanchions, front and rear Front and rear early small deck extension Positionable tapered (early) drop steps, front and rear Early treadplate 81” low short hood with ratchet handbrake Early straight grabs and “flipped” nut-bolt-washer (NBW) mounting on nose front and top Latched battery box doors with narrow louvers and tab-style (early) hinges Early cab sub-base doors without reinforcement ribs, both sides Single right rear cab step Cab Sub-Base Step Guards Early cab step guards (long taper) No hopper water piping underneath front battery box step Standard EMD high headlight with glare visors in numberboard housing “35-Line” cab with standard front windshields, and standard armrests, both sides Detailed cab interior with separate floor, cab blowers, rear wall, late seats with armrests, and standard AAR control stand Positionable cab side windows “Salem” combination mirror & windshield wing mounted ahead of the cab side windows, both sides Standard EMD sunshades with long mounting tracks Long hood with standard electrical cabinet seam, bolted generator compartment door, and early inertial drain hole placement (wide spacing on engineer’s side, low on fireman’s side) Small ECAFB Early (smooth) blower duct housing Early long handrail stanchion spacing with “short” stanchions at thin section of sidesill Early inertial air intake grilles without drip rails Standard turbo exhaust stack Early extended-range dynamic brake housing (short tapers), with retrofitted long contactor door See-through 48” standard-height dynamic brake fan housing with 10-blade fan and hub assembly, with spiral-grill and center cap Dynamic brake intakes with see-through intake vanes, and resistor grid detail inside of the housing Diamond-mesh radiator intake screening See-through standard-height 48” radiator fan housings with 8-blade fan and hub assembly Separately-applied radiator core detail mounted inside of long hood, visible under radiator fans Curved radiator fan grab iron Rear LED-illuminated horizontal headlight and standard housing Early rear sander door catch placement (inboard) Underbody frame rails with separately-applied plumbing and traction motor cable bundle details Detailed Blomberg-B truck frames (LFM-cast) with Hyatt bearing housings, separately-applied brake cylinders in released (piston retracted) position, elliptical springs, end transom detail, separate sanding lines and brackets, deleted outer brake shoes, and separate swing hanger detail Separately-applied flexible neoprene sanding lines at stepwell ends of trucks Rust-color painted wheelsets “Aeroquip” brand speed recorder with adapter flange mounted to right #2 axle ATC Pickup shoe on #1 axle, right side Standard 4 jacking pads Frame-mounted bell Salem-brand #824-170 and #818-170 primary and secondary centrifugal air filters, respectively (accordion-style) Separately-applied brake vent regulator valve and plumbing detail on underbody 3600-gallon fuel tank with early mounting brackets, inset dial gauge on right side, and early rear drain bar Separately-applied fuel fillers, drains, and breather piping on fuel tanks Separately-applied engine oil sump drain fitting with hose Separately-applied radiator water drain fitting on underbody Separately-applied truck air line plumbing on underbody above each truck, both sides Separately-applied wireform grab irons, wireform lift rings, etched windshield wipers, trainline hoses, sand hatch covers, and more Motor with 5-pole skew-wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Paint colors match Tru-Color Paint color: TCP-109 C&NW Green TCP-353 C&NW Early Yellow Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended Radius: 22” DCC & sound-equipped locomotives also feature: ESU LokSound 5 DCC & Sound decoder with “Full Throttle” functions Two (2) cube-type speakers Turbocharged EMD 16-645 prime mover sounds ESU designed “PowerPack” with two super capacitors**** Operates on both DC and DCC layouts
Produktgewicht inkl. Verpackung: 1,320 kgNeuerscheinung! Auslieferung Dezember 2024
Vorbestellfrist für garantierte Lieferung: 26.02.2024
Road Number-Specific ScaleTrains All-new model Era: 1980s – 1990s Series C&NW 5500-5537; ex-NYC 3010-3049, built Nov/Dec 1965 C&NW 5505 Lost-wax cast brass Leslie S-3-LR horn mounted on number board housing Excalibur low-profile “ice skate” communications antenna mounted to cab roof Front EMD low plow with MU hose doors White corner step edges and kickplates “OY” Scheme, “Employee Owned” logo C&NW 5506 Lost-wax cast brass Leslie SU-3L-LR horn mounted on number board housing Excalibur low-profile “ice skate” communications antenna mounted to cab roof Front EMD medium plow without MU hose doors Green walkway duct Green air reservoirs White corner step edges and kickplates “OY” Scheme, “Employee Owned” logo C&NW 5525 Lost-wax cast brass Leslie S-3-LR horn mounted on number board housing Excalibur low-profile “ice skate” communications antenna mounted to cab roof Front EMD medium plow without MU hose doors Green walkway duct Green air reservoirs White corner step edges and kickplates “OY” Scheme, “Employee Owned” logo Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-Illuminated rectangular walkway lights mounted between front and rear sanding valve doors, and round walkway light aft of raised walkway duct* LED-illuminated tri-color, flush-mounted front and rear class lights with raised gaskets LED-illuminated Tomar 804-1274 Strobe* Printed number boards with separately-controlled, backlit LED-illumination* 3-hose multiple unit (MU) hose groups with mounting bracket and gladhand detail Semi-scale coupler buffers equipped with durable metal semi-scale Type E knuckle couplers Front and rear straight uncoupling levers with straight rod extensions Notched-corner pilot face with square access plate, front and rear “Early” angled deck-mounted multiple unit (MU) receptacles, dual per end, front and rear “Short” stepwells with nub-bottom pilots, front and rear End handrails with deck and pilot face-mounted stanchions, front and rear Front and rear early small deck extension Positionable tapered (early) drop steps, front and rear Early treadplate 81” low short hood with ratchet handbrake Early straight grabs and “flipped” nut-bolt-washer (NBW) mounting on nose front and top Latched battery box doors with narrow louvers and tab-style (early) hinges Early cab sub-base doors without reinforcement ribs, both sides Single right rear cab step Cab Sub-Base Step Guards Early cab step guards (long taper) No hopper water piping underneath front battery box step Standard EMD high headlight with glare visors in numberboard housing “35-Line” cab with standard front windshields, and standard armrests, both sides Detailed cab interior with separate floor, cab blowers, rear wall, late seats with armrests, and standard AAR control stand Positionable cab side windows “Salem” combination mirror & windshield wing mounted ahead of the cab side windows, both sides Standard EMD sunshades with long mounting tracks Long hood with standard electrical cabinet seam, bolted generator compartment door, and early inertial drain hole placement (wide spacing on engineer’s side, low on fireman’s side) Small ECAFB Early (smooth) blower duct housing Early long handrail stanchion spacing with “short” stanchions at thin section of sidesill Early inertial air intake grilles without drip rails Standard turbo exhaust stack Early extended-range dynamic brake housing (short tapers), with retrofitted long contactor door See-through 48” standard-height dynamic brake fan housing with 10-blade fan and hub assembly, with spiral-grill and center cap Dynamic brake intakes with see-through intake vanes, and resistor grid detail inside of the housing Diamond-mesh radiator intake screening See-through standard-height 48” radiator fan housings with 8-blade fan and hub assembly Separately-applied radiator core detail mounted inside of long hood, visible under radiator fans Curved radiator fan grab iron Rear LED-illuminated horizontal headlight and standard housing Early rear sander door catch placement (inboard) Underbody frame rails with separately-applied plumbing and traction motor cable bundle details Detailed Blomberg-B truck frames (LFM-cast) with Hyatt bearing housings, separately-applied brake cylinders in released (piston retracted) position, elliptical springs, end transom detail, separate sanding lines and brackets, deleted outer brake shoes, and separate swing hanger detail Separately-applied flexible neoprene sanding lines at stepwell ends of trucks Rust-color painted wheelsets “Aeroquip” brand speed recorder with adapter flange mounted to right #2 axle ATC Pickup shoe on #1 axle, right side Standard 4 jacking pads Frame-mounted bell Salem-brand #824-170 and #818-170 primary and secondary centrifugal air filters, respectively (accordion-style) Separately-applied brake vent regulator valve and plumbing detail on underbody 3600-gallon fuel tank with early mounting brackets, inset dial gauge on right side, and early rear drain bar Separately-applied fuel fillers, drains, and breather piping on fuel tanks Separately-applied engine oil sump drain fitting with hose Separately-applied radiator water drain fitting on underbody Separately-applied truck air line plumbing on underbody above each truck, both sides Separately-applied wireform grab irons, wireform lift rings, etched windshield wipers, trainline hoses, sand hatch covers, and more Motor with 5-pole skew-wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Paint colors match Tru-Color Paint color: TCP-109 C&NW Green TCP-353 C&NW Early Yellow Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended Radius: 22” DCC & sound-equipped locomotives also feature: ESU LokSound 5 DCC & Sound decoder with “Full Throttle” functions Two (2) cube-type speakers Turbocharged EMD 16-645 prime mover sounds ESU designed “PowerPack” with two super capacitors**** Operates on both DC and DCC layouts
Produktgewicht inkl. Verpackung: 1,320 kgNeuerscheinung! Auslieferung Dezember 2024
Vorbestellfrist für garantierte Lieferung: 26.02.2024
Road Number-Specific ScaleTrains All-new model Era: 1980s – 1990s Series C&NW 5500-5537; ex-NYC 3010-3049, built Nov/Dec 1965 C&NW 5505 Lost-wax cast brass Leslie S-3-LR horn mounted on number board housing Excalibur low-profile “ice skate” communications antenna mounted to cab roof Front EMD low plow with MU hose doors White corner step edges and kickplates “OY” Scheme, “Employee Owned” logo C&NW 5506 Lost-wax cast brass Leslie SU-3L-LR horn mounted on number board housing Excalibur low-profile “ice skate” communications antenna mounted to cab roof Front EMD medium plow without MU hose doors Green walkway duct Green air reservoirs White corner step edges and kickplates “OY” Scheme, “Employee Owned” logo C&NW 5525 Lost-wax cast brass Leslie S-3-LR horn mounted on number board housing Excalibur low-profile “ice skate” communications antenna mounted to cab roof Front EMD medium plow without MU hose doors Green walkway duct Green air reservoirs White corner step edges and kickplates “OY” Scheme, “Employee Owned” logo Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-Illuminated rectangular walkway lights mounted between front and rear sanding valve doors, and round walkway light aft of raised walkway duct* LED-illuminated tri-color, flush-mounted front and rear class lights with raised gaskets LED-illuminated Tomar 804-1274 Strobe* Printed number boards with separately-controlled, backlit LED-illumination* 3-hose multiple unit (MU) hose groups with mounting bracket and gladhand detail Semi-scale coupler buffers equipped with durable metal semi-scale Type E knuckle couplers Front and rear straight uncoupling levers with straight rod extensions Notched-corner pilot face with square access plate, front and rear “Early” angled deck-mounted multiple unit (MU) receptacles, dual per end, front and rear “Short” stepwells with nub-bottom pilots, front and rear End handrails with deck and pilot face-mounted stanchions, front and rear Front and rear early small deck extension Positionable tapered (early) drop steps, front and rear Early treadplate 81” low short hood with ratchet handbrake Early straight grabs and “flipped” nut-bolt-washer (NBW) mounting on nose front and top Latched battery box doors with narrow louvers and tab-style (early) hinges Early cab sub-base doors without reinforcement ribs, both sides Single right rear cab step Cab Sub-Base Step Guards Early cab step guards (long taper) No hopper water piping underneath front battery box step Standard EMD high headlight with glare visors in numberboard housing “35-Line” cab with standard front windshields, and standard armrests, both sides Detailed cab interior with separate floor, cab blowers, rear wall, late seats with armrests, and standard AAR control stand Positionable cab side windows “Salem” combination mirror & windshield wing mounted ahead of the cab side windows, both sides Standard EMD sunshades with long mounting tracks Long hood with standard electrical cabinet seam, bolted generator compartment door, and early inertial drain hole placement (wide spacing on engineer’s side, low on fireman’s side) Small ECAFB Early (smooth) blower duct housing Early long handrail stanchion spacing with “short” stanchions at thin section of sidesill Early inertial air intake grilles without drip rails Standard turbo exhaust stack Early extended-range dynamic brake housing (short tapers), with retrofitted long contactor door See-through 48” standard-height dynamic brake fan housing with 10-blade fan and hub assembly, with spiral-grill and center cap Dynamic brake intakes with see-through intake vanes, and resistor grid detail inside of the housing Diamond-mesh radiator intake screening See-through standard-height 48” radiator fan housings with 8-blade fan and hub assembly Separately-applied radiator core detail mounted inside of long hood, visible under radiator fans Curved radiator fan grab iron Rear LED-illuminated horizontal headlight and standard housing Early rear sander door catch placement (inboard) Underbody frame rails with separately-applied plumbing and traction motor cable bundle details Detailed Blomberg-B truck frames (LFM-cast) with Hyatt bearing housings, separately-applied brake cylinders in released (piston retracted) position, elliptical springs, end transom detail, separate sanding lines and brackets, deleted outer brake shoes, and separate swing hanger detail Separately-applied flexible neoprene sanding lines at stepwell ends of trucks Rust-color painted wheelsets “Aeroquip” brand speed recorder with adapter flange mounted to right #2 axle ATC Pickup shoe on #1 axle, right side Standard 4 jacking pads Frame-mounted bell Salem-brand #824-170 and #818-170 primary and secondary centrifugal air filters, respectively (accordion-style) Separately-applied brake vent regulator valve and plumbing detail on underbody 3600-gallon fuel tank with early mounting brackets, inset dial gauge on right side, and early rear drain bar Separately-applied fuel fillers, drains, and breather piping on fuel tanks Separately-applied engine oil sump drain fitting with hose Separately-applied radiator water drain fitting on underbody Separately-applied truck air line plumbing on underbody above each truck, both sides Separately-applied wireform grab irons, wireform lift rings, etched windshield wipers, trainline hoses, sand hatch covers, and more Motor with 5-pole skew-wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Paint colors match Tru-Color Paint color: TCP-109 C&NW Green TCP-353 C&NW Early Yellow Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended Radius: 22” DCC & sound-equipped locomotives also feature: ESU LokSound 5 DCC & Sound decoder with “Full Throttle” functions Two (2) cube-type speakers Turbocharged EMD 16-645 prime mover sounds ESU designed “PowerPack” with two super capacitors**** Operates on both DC and DCC layouts
Produktgewicht inkl. Verpackung: 1,320 kgNeuerscheinung! Auslieferung Dezember 2024
Vorbestellfrist für garantierte Lieferung: 26.02.2024
Road Number-Specific ScaleTrains All-new model Era: 1980s – 1990s Series C&NW 5500-5537; ex-NYC 3010-3049, built Nov/Dec 1965 C&NW 5505 Lost-wax cast brass Leslie S-3-LR horn mounted on number board housing Excalibur low-profile “ice skate” communications antenna mounted to cab roof Front EMD low plow with MU hose doors White corner step edges and kickplates “OY” Scheme, “Employee Owned” logo C&NW 5506 Lost-wax cast brass Leslie SU-3L-LR horn mounted on number board housing Excalibur low-profile “ice skate” communications antenna mounted to cab roof Front EMD medium plow without MU hose doors Green walkway duct Green air reservoirs White corner step edges and kickplates “OY” Scheme, “Employee Owned” logo C&NW 5525 Lost-wax cast brass Leslie S-3-LR horn mounted on number board housing Excalibur low-profile “ice skate” communications antenna mounted to cab roof Front EMD medium plow without MU hose doors Green walkway duct Green air reservoirs White corner step edges and kickplates “OY” Scheme, “Employee Owned” logo Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-Illuminated rectangular walkway lights mounted between front and rear sanding valve doors, and round walkway light aft of raised walkway duct* LED-illuminated tri-color, flush-mounted front and rear class lights with raised gaskets LED-illuminated Tomar 804-1274 Strobe* Printed number boards with separately-controlled, backlit LED-illumination* 3-hose multiple unit (MU) hose groups with mounting bracket and gladhand detail Semi-scale coupler buffers equipped with durable metal semi-scale Type E knuckle couplers Front and rear straight uncoupling levers with straight rod extensions Notched-corner pilot face with square access plate, front and rear “Early” angled deck-mounted multiple unit (MU) receptacles, dual per end, front and rear “Short” stepwells with nub-bottom pilots, front and rear End handrails with deck and pilot face-mounted stanchions, front and rear Front and rear early small deck extension Positionable tapered (early) drop steps, front and rear Early treadplate 81” low short hood with ratchet handbrake Early straight grabs and “flipped” nut-bolt-washer (NBW) mounting on nose front and top Latched battery box doors with narrow louvers and tab-style (early) hinges Early cab sub-base doors without reinforcement ribs, both sides Single right rear cab step Cab Sub-Base Step Guards Early cab step guards (long taper) No hopper water piping underneath front battery box step Standard EMD high headlight with glare visors in numberboard housing “35-Line” cab with standard front windshields, and standard armrests, both sides Detailed cab interior with separate floor, cab blowers, rear wall, late seats with armrests, and standard AAR control stand Positionable cab side windows “Salem” combination mirror & windshield wing mounted ahead of the cab side windows, both sides Standard EMD sunshades with long mounting tracks Long hood with standard electrical cabinet seam, bolted generator compartment door, and early inertial drain hole placement (wide spacing on engineer’s side, low on fireman’s side) Small ECAFB Early (smooth) blower duct housing Early long handrail stanchion spacing with “short” stanchions at thin section of sidesill Early inertial air intake grilles without drip rails Standard turbo exhaust stack Early extended-range dynamic brake housing (short tapers), with retrofitted long contactor door See-through 48” standard-height dynamic brake fan housing with 10-blade fan and hub assembly, with spiral-grill and center cap Dynamic brake intakes with see-through intake vanes, and resistor grid detail inside of the housing Diamond-mesh radiator intake screening See-through standard-height 48” radiator fan housings with 8-blade fan and hub assembly Separately-applied radiator core detail mounted inside of long hood, visible under radiator fans Curved radiator fan grab iron Rear LED-illuminated horizontal headlight and standard housing Early rear sander door catch placement (inboard) Underbody frame rails with separately-applied plumbing and traction motor cable bundle details Detailed Blomberg-B truck frames (LFM-cast) with Hyatt bearing housings, separately-applied brake cylinders in released (piston retracted) position, elliptical springs, end transom detail, separate sanding lines and brackets, deleted outer brake shoes, and separate swing hanger detail Separately-applied flexible neoprene sanding lines at stepwell ends of trucks Rust-color painted wheelsets “Aeroquip” brand speed recorder with adapter flange mounted to right #2 axle ATC Pickup shoe on #1 axle, right side Standard 4 jacking pads Frame-mounted bell Salem-brand #824-170 and #818-170 primary and secondary centrifugal air filters, respectively (accordion-style) Separately-applied brake vent regulator valve and plumbing detail on underbody 3600-gallon fuel tank with early mounting brackets, inset dial gauge on right side, and early rear drain bar Separately-applied fuel fillers, drains, and breather piping on fuel tanks Separately-applied engine oil sump drain fitting with hose Separately-applied radiator water drain fitting on underbody Separately-applied truck air line plumbing on underbody above each truck, both sides Separately-applied wireform grab irons, wireform lift rings, etched windshield wipers, trainline hoses, sand hatch covers, and more Motor with 5-pole skew-wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Paint colors match Tru-Color Paint color: TCP-109 C&NW Green TCP-353 C&NW Early Yellow Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended Radius: 22” DC/DCC & sound ready locomotives also feature: Operates on DC layouts DCC-ready with 21-pin connector
Produktgewicht inkl. Verpackung: 1,320 kgNeuerscheinung! Auslieferung Dezember 2024
Vorbestellfrist für garantierte Lieferung: 26.02.2024
Road Number-Specific ScaleTrains All-new model Era: 1980s – 1990s Series C&NW 5500-5537; ex-NYC 3010-3049, built Nov/Dec 1965 C&NW 5505 Lost-wax cast brass Leslie S-3-LR horn mounted on number board housing Excalibur low-profile “ice skate” communications antenna mounted to cab roof Front EMD low plow with MU hose doors White corner step edges and kickplates “OY” Scheme, “Employee Owned” logo C&NW 5506 Lost-wax cast brass Leslie SU-3L-LR horn mounted on number board housing Excalibur low-profile “ice skate” communications antenna mounted to cab roof Front EMD medium plow without MU hose doors Green walkway duct Green air reservoirs White corner step edges and kickplates “OY” Scheme, “Employee Owned” logo C&NW 5525 Lost-wax cast brass Leslie S-3-LR horn mounted on number board housing Excalibur low-profile “ice skate” communications antenna mounted to cab roof Front EMD medium plow without MU hose doors Green walkway duct Green air reservoirs White corner step edges and kickplates “OY” Scheme, “Employee Owned” logo Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-Illuminated rectangular walkway lights mounted between front and rear sanding valve doors, and round walkway light aft of raised walkway duct* LED-illuminated tri-color, flush-mounted front and rear class lights with raised gaskets LED-illuminated Tomar 804-1274 Strobe* Printed number boards with separately-controlled, backlit LED-illumination* 3-hose multiple unit (MU) hose groups with mounting bracket and gladhand detail Semi-scale coupler buffers equipped with durable metal semi-scale Type E knuckle couplers Front and rear straight uncoupling levers with straight rod extensions Notched-corner pilot face with square access plate, front and rear “Early” angled deck-mounted multiple unit (MU) receptacles, dual per end, front and rear “Short” stepwells with nub-bottom pilots, front and rear End handrails with deck and pilot face-mounted stanchions, front and rear Front and rear early small deck extension Positionable tapered (early) drop steps, front and rear Early treadplate 81” low short hood with ratchet handbrake Early straight grabs and “flipped” nut-bolt-washer (NBW) mounting on nose front and top Latched battery box doors with narrow louvers and tab-style (early) hinges Early cab sub-base doors without reinforcement ribs, both sides Single right rear cab step Cab Sub-Base Step Guards Early cab step guards (long taper) No hopper water piping underneath front battery box step Standard EMD high headlight with glare visors in numberboard housing “35-Line” cab with standard front windshields, and standard armrests, both sides Detailed cab interior with separate floor, cab blowers, rear wall, late seats with armrests, and standard AAR control stand Positionable cab side windows “Salem” combination mirror & windshield wing mounted ahead of the cab side windows, both sides Standard EMD sunshades with long mounting tracks Long hood with standard electrical cabinet seam, bolted generator compartment door, and early inertial drain hole placement (wide spacing on engineer’s side, low on fireman’s side) Small ECAFB Early (smooth) blower duct housing Early long handrail stanchion spacing with “short” stanchions at thin section of sidesill Early inertial air intake grilles without drip rails Standard turbo exhaust stack Early extended-range dynamic brake housing (short tapers), with retrofitted long contactor door See-through 48” standard-height dynamic brake fan housing with 10-blade fan and hub assembly, with spiral-grill and center cap Dynamic brake intakes with see-through intake vanes, and resistor grid detail inside of the housing Diamond-mesh radiator intake screening See-through standard-height 48” radiator fan housings with 8-blade fan and hub assembly Separately-applied radiator core detail mounted inside of long hood, visible under radiator fans Curved radiator fan grab iron Rear LED-illuminated horizontal headlight and standard housing Early rear sander door catch placement (inboard) Underbody frame rails with separately-applied plumbing and traction motor cable bundle details Detailed Blomberg-B truck frames (LFM-cast) with Hyatt bearing housings, separately-applied brake cylinders in released (piston retracted) position, elliptical springs, end transom detail, separate sanding lines and brackets, deleted outer brake shoes, and separate swing hanger detail Separately-applied flexible neoprene sanding lines at stepwell ends of trucks Rust-color painted wheelsets “Aeroquip” brand speed recorder with adapter flange mounted to right #2 axle ATC Pickup shoe on #1 axle, right side Standard 4 jacking pads Frame-mounted bell Salem-brand #824-170 and #818-170 primary and secondary centrifugal air filters, respectively (accordion-style) Separately-applied brake vent regulator valve and plumbing detail on underbody 3600-gallon fuel tank with early mounting brackets, inset dial gauge on right side, and early rear drain bar Separately-applied fuel fillers, drains, and breather piping on fuel tanks Separately-applied engine oil sump drain fitting with hose Separately-applied radiator water drain fitting on underbody Separately-applied truck air line plumbing on underbody above each truck, both sides Separately-applied wireform grab irons, wireform lift rings, etched windshield wipers, trainline hoses, sand hatch covers, and more Motor with 5-pole skew-wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Paint colors match Tru-Color Paint color: TCP-109 C&NW Green TCP-353 C&NW Early Yellow Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended Radius: 22” DC/DCC & sound ready locomotives also feature: Operates on DC layouts DCC-ready with 21-pin connector
Produktgewicht inkl. Verpackung: 1,320 kgNeuerscheinung! Auslieferung Dezember 2024
Vorbestellfrist für garantierte Lieferung: 26.02.2024
Road Number-Specific ScaleTrains All-new model Era: 1980s – 1990s Series C&NW 5500-5537; ex-NYC 3010-3049, built Nov/Dec 1965 C&NW 5505 Lost-wax cast brass Leslie S-3-LR horn mounted on number board housing Excalibur low-profile “ice skate” communications antenna mounted to cab roof Front EMD low plow with MU hose doors White corner step edges and kickplates “OY” Scheme, “Employee Owned” logo C&NW 5506 Lost-wax cast brass Leslie SU-3L-LR horn mounted on number board housing Excalibur low-profile “ice skate” communications antenna mounted to cab roof Front EMD medium plow without MU hose doors Green walkway duct Green air reservoirs White corner step edges and kickplates “OY” Scheme, “Employee Owned” logo C&NW 5525 Lost-wax cast brass Leslie S-3-LR horn mounted on number board housing Excalibur low-profile “ice skate” communications antenna mounted to cab roof Front EMD medium plow without MU hose doors Green walkway duct Green air reservoirs White corner step edges and kickplates “OY” Scheme, “Employee Owned” logo Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-Illuminated rectangular walkway lights mounted between front and rear sanding valve doors, and round walkway light aft of raised walkway duct* LED-illuminated tri-color, flush-mounted front and rear class lights with raised gaskets LED-illuminated Tomar 804-1274 Strobe* Printed number boards with separately-controlled, backlit LED-illumination* 3-hose multiple unit (MU) hose groups with mounting bracket and gladhand detail Semi-scale coupler buffers equipped with durable metal semi-scale Type E knuckle couplers Front and rear straight uncoupling levers with straight rod extensions Notched-corner pilot face with square access plate, front and rear “Early” angled deck-mounted multiple unit (MU) receptacles, dual per end, front and rear “Short” stepwells with nub-bottom pilots, front and rear End handrails with deck and pilot face-mounted stanchions, front and rear Front and rear early small deck extension Positionable tapered (early) drop steps, front and rear Early treadplate 81” low short hood with ratchet handbrake Early straight grabs and “flipped” nut-bolt-washer (NBW) mounting on nose front and top Latched battery box doors with narrow louvers and tab-style (early) hinges Early cab sub-base doors without reinforcement ribs, both sides Single right rear cab step Cab Sub-Base Step Guards Early cab step guards (long taper) No hopper water piping underneath front battery box step Standard EMD high headlight with glare visors in numberboard housing “35-Line” cab with standard front windshields, and standard armrests, both sides Detailed cab interior with separate floor, cab blowers, rear wall, late seats with armrests, and standard AAR control stand Positionable cab side windows “Salem” combination mirror & windshield wing mounted ahead of the cab side windows, both sides Standard EMD sunshades with long mounting tracks Long hood with standard electrical cabinet seam, bolted generator compartment door, and early inertial drain hole placement (wide spacing on engineer’s side, low on fireman’s side) Small ECAFB Early (smooth) blower duct housing Early long handrail stanchion spacing with “short” stanchions at thin section of sidesill Early inertial air intake grilles without drip rails Standard turbo exhaust stack Early extended-range dynamic brake housing (short tapers), with retrofitted long contactor door See-through 48” standard-height dynamic brake fan housing with 10-blade fan and hub assembly, with spiral-grill and center cap Dynamic brake intakes with see-through intake vanes, and resistor grid detail inside of the housing Diamond-mesh radiator intake screening See-through standard-height 48” radiator fan housings with 8-blade fan and hub assembly Separately-applied radiator core detail mounted inside of long hood, visible under radiator fans Curved radiator fan grab iron Rear LED-illuminated horizontal headlight and standard housing Early rear sander door catch placement (inboard) Underbody frame rails with separately-applied plumbing and traction motor cable bundle details Detailed Blomberg-B truck frames (LFM-cast) with Hyatt bearing housings, separately-applied brake cylinders in released (piston retracted) position, elliptical springs, end transom detail, separate sanding lines and brackets, deleted outer brake shoes, and separate swing hanger detail Separately-applied flexible neoprene sanding lines at stepwell ends of trucks Rust-color painted wheelsets “Aeroquip” brand speed recorder with adapter flange mounted to right #2 axle ATC Pickup shoe on #1 axle, right side Standard 4 jacking pads Frame-mounted bell Salem-brand #824-170 and #818-170 primary and secondary centrifugal air filters, respectively (accordion-style) Separately-applied brake vent regulator valve and plumbing detail on underbody 3600-gallon fuel tank with early mounting brackets, inset dial gauge on right side, and early rear drain bar Separately-applied fuel fillers, drains, and breather piping on fuel tanks Separately-applied engine oil sump drain fitting with hose Separately-applied radiator water drain fitting on underbody Separately-applied truck air line plumbing on underbody above each truck, both sides Separately-applied wireform grab irons, wireform lift rings, etched windshield wipers, trainline hoses, sand hatch covers, and more Motor with 5-pole skew-wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Paint colors match Tru-Color Paint color: TCP-109 C&NW Green TCP-353 C&NW Early Yellow Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended Radius: 22” DC/DCC & sound ready locomotives also feature: Operates on DC layouts DCC-ready with 21-pin connector
Produktgewicht inkl. Verpackung: 1,320 kgNeuerscheinung! Auslieferung Dezember 2024
Vorbestellfrist für garantierte Lieferung: 26.02.2024
Road Number-Specific ScaleTrains All-new model Era: 1970s-era Series 3086 to 3093, built Nov/1971 D&RGW 3087, 3088, 3089, 3090, and 3093: EMD square-corner “Burnham” number boards D&RGW 3092: Original EMD number boards Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-Illuminated rectangular walkway lights mounted between front and rear sanding valve doors, and round walkway light aft of raised walkway duct* LED-illuminated Mars SBW-2-301 dual signal light (clear lenses) mounted in low short hood* LED-illuminated tri-color, flush-mounted front and rear class lights with raised gaskets Printed number boards with separately-controlled, backlit LED-illumination* Front EMD low plow with MU hose doors 3-hose multiple unit (MU) hose groups with mounting bracket and gladhand detail Semi-scale coupler buffers equipped with durable metal semi-scale Type E knuckle couplers Front and rear straight uncoupling levers without loop handles Square-corner pilot face with angled lifting slots, front and rear “Late” tall deck-mounted multiple-unit (MU) receptacles, front and rear “Tall” stepwells with “zig-zag” pilots, front and rear End handrails with deck-mounted stanchions, front and rear Front and rear early small deck extension Positionable straight (late) drop steps, front and rear Late treadplate 81” low short hood with ratchet handbrake Late drop grabs and standard nut-bolt-washer (NBW) mounting on nose front and top Latched battery box doors with narrow louvers and tab-style (early) hinges Early cab sub-base doors with non-terminating reinforcement ribs, both sides Dual right rear cab steps Late cab step guards (short taper) Hopper water piping underneath front battery box step Standard EMD high headlight with glare visors in numberboard housing “35-Line” cab with standard armrests, and flag holder bracket on right side (D&RGW) Detailed cab interior with separate floor, cab blowers, rear wall, early seats, and standard AAR control stand Positionable cab side windows Tall square-corner clear wind wings mounted fore and aft of cab side window, both sides of cab Standard EMD sunshades with long mounting tracks Lost-wax cast brass Nathan AirChime M3 (M3R1) horn mounted on number board housing Excalibur low-profile “ice skate” communications antenna mounted to cab roof Long hood with standard electrical cabinet seam, bolted generator compartment door, and late inertial drain hole placement (close spacing on engineer’s side, high on fireman’s side) Small ECAFB Late (ribbed) blower duct housing Late long handrail stanchion spacing with all “tall” stanchions overall Early inertial air intake grilles without drip rails Standard turbo exhaust stack Late standard-range dynamic brake housing (long tapers), with rectangular vent See-through 48” dynamic brake fan housing mounted on riser ring with 10-blade fan and hub assembly, with concentric-ring grill Dynamic brake intakes with see-through intake vanes, and resistor grid detail inside of the housing Rectangular-mesh radiator intake screening See-through standard-height 48” radiator fan housings with 8-blade fan and hub assembly Separately-applied radiator core detail mounted inside of long hood, visible under radiator fans Curved radiator fan grab iron Rear LED-illuminated horizontal headlight and standard housing Late rear sander door catch placement (outboard) Underbody frame rails with separately-applied plumbing and traction motor cable bundle details Detailed Blomberg-B truck frames (LFM-cast) with Hyatt bearing housings, separately-applied brake cylinders in released (piston retracted) position, elliptical springs, end transom detail, separate sanding lines and brackets, and separate swing hanger detail Separately-applied flexible neoprene sanding lines at both ends of trucks Rust-color painted wheelsets Early EMD speed recorder mounted to right #1 axle “McCarty” type re-rail frogs ACI labels mounted to blower duct on left side, and rear cab step kickplate on right side Standard 4 jacking pads Frame-mounted bell Salem-brand #824-170 and #818-170 primary and secondary centrifugal air filters, respectively (accordion-style) Separately-applied brake vent regulator valve and plumbing detail on underbody 3600-gallon fuel tank with late mounting brackets, inset dial gauge on both sides, and late rear drain bar Separately-applied fuel fillers, drains, and breather piping on fuel tanks Separately-applied engine oil sump drain fitting with hose Separately-applied radiator water drain fitting on underbody Separately-applied truck air line plumbing on underbody above each truck, both sides Separately-applied wireform grab irons, wireform lift rings, etched windshield wipers, trainline hoses, sand hatch covers, and more Motor with 5-pole skew-wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended Radius: 22” DCC & sound-equipped locomotives also feature: ESU LokSound 5 DCC & Sound decoder with “Full Throttle” functions Two (2) cube-type speakers Turbocharged EMD 16-645 prime mover sounds ESU designed “PowerPack” with two super capacitors**** Operates on both DC and DCC layouts
Produktgewicht inkl. Verpackung: 1,320 kgNeuerscheinung! Auslieferung Dezember 2024
Vorbestellfrist für garantierte Lieferung: 26.02.2024
Road Number-Specific ScaleTrains All-new model Era: 1970s-era Series 3086 to 3093, built Nov/1971 D&RGW 3087, 3088, 3089, 3090, and 3093: EMD square-corner “Burnham” number boards D&RGW 3092: Original EMD number boards Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-Illuminated rectangular walkway lights mounted between front and rear sanding valve doors, and round walkway light aft of raised walkway duct* LED-illuminated Mars SBW-2-301 dual signal light (clear lenses) mounted in low short hood* LED-illuminated tri-color, flush-mounted front and rear class lights with raised gaskets Printed number boards with separately-controlled, backlit LED-illumination* Front EMD low plow with MU hose doors 3-hose multiple unit (MU) hose groups with mounting bracket and gladhand detail Semi-scale coupler buffers equipped with durable metal semi-scale Type E knuckle couplers Front and rear straight uncoupling levers without loop handles Square-corner pilot face with angled lifting slots, front and rear “Late” tall deck-mounted multiple-unit (MU) receptacles, front and rear “Tall” stepwells with “zig-zag” pilots, front and rear End handrails with deck-mounted stanchions, front and rear Front and rear early small deck extension Positionable straight (late) drop steps, front and rear Late treadplate 81” low short hood with ratchet handbrake Late drop grabs and standard nut-bolt-washer (NBW) mounting on nose front and top Latched battery box doors with narrow louvers and tab-style (early) hinges Early cab sub-base doors with non-terminating reinforcement ribs, both sides Dual right rear cab steps Late cab step guards (short taper) Hopper water piping underneath front battery box step Standard EMD high headlight with glare visors in numberboard housing “35-Line” cab with standard armrests, and flag holder bracket on right side (D&RGW) Detailed cab interior with separate floor, cab blowers, rear wall, early seats, and standard AAR control stand Positionable cab side windows Tall square-corner clear wind wings mounted fore and aft of cab side window, both sides of cab Standard EMD sunshades with long mounting tracks Lost-wax cast brass Nathan AirChime M3 (M3R1) horn mounted on number board housing Excalibur low-profile “ice skate” communications antenna mounted to cab roof Long hood with standard electrical cabinet seam, bolted generator compartment door, and late inertial drain hole placement (close spacing on engineer’s side, high on fireman’s side) Small ECAFB Late (ribbed) blower duct housing Late long handrail stanchion spacing with all “tall” stanchions overall Early inertial air intake grilles without drip rails Standard turbo exhaust stack Late standard-range dynamic brake housing (long tapers), with rectangular vent See-through 48” dynamic brake fan housing mounted on riser ring with 10-blade fan and hub assembly, with concentric-ring grill Dynamic brake intakes with see-through intake vanes, and resistor grid detail inside of the housing Rectangular-mesh radiator intake screening See-through standard-height 48” radiator fan housings with 8-blade fan and hub assembly Separately-applied radiator core detail mounted inside of long hood, visible under radiator fans Curved radiator fan grab iron Rear LED-illuminated horizontal headlight and standard housing Late rear sander door catch placement (outboard) Underbody frame rails with separately-applied plumbing and traction motor cable bundle details Detailed Blomberg-B truck frames (LFM-cast) with Hyatt bearing housings, separately-applied brake cylinders in released (piston retracted) position, elliptical springs, end transom detail, separate sanding lines and brackets, and separate swing hanger detail Separately-applied flexible neoprene sanding lines at both ends of trucks Rust-color painted wheelsets Early EMD speed recorder mounted to right #1 axle “McCarty” type re-rail frogs ACI labels mounted to blower duct on left side, and rear cab step kickplate on right side Standard 4 jacking pads Frame-mounted bell Salem-brand #824-170 and #818-170 primary and secondary centrifugal air filters, respectively (accordion-style) Separately-applied brake vent regulator valve and plumbing detail on underbody 3600-gallon fuel tank with late mounting brackets, inset dial gauge on both sides, and late rear drain bar Separately-applied fuel fillers, drains, and breather piping on fuel tanks Separately-applied engine oil sump drain fitting with hose Separately-applied radiator water drain fitting on underbody Separately-applied truck air line plumbing on underbody above each truck, both sides Separately-applied wireform grab irons, wireform lift rings, etched windshield wipers, trainline hoses, sand hatch covers, and more Motor with 5-pole skew-wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended Radius: 22” DCC & sound-equipped locomotives also feature: ESU LokSound 5 DCC & Sound decoder with “Full Throttle” functions Two (2) cube-type speakers Turbocharged EMD 16-645 prime mover sounds ESU designed “PowerPack” with two super capacitors**** Operates on both DC and DCC layouts
Produktgewicht inkl. Verpackung: 1,320 kgNeuerscheinung! Auslieferung Dezember 2024
Vorbestellfrist für garantierte Lieferung: 26.02.2024
Road Number-Specific ScaleTrains All-new model Era: 1970s-era Series 3086 to 3093, built Nov/1971 D&RGW 3087, 3088, 3089, 3090, and 3093: EMD square-corner “Burnham” number boards D&RGW 3092: Original EMD number boards Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-Illuminated rectangular walkway lights mounted between front and rear sanding valve doors, and round walkway light aft of raised walkway duct* LED-illuminated Mars SBW-2-301 dual signal light (clear lenses) mounted in low short hood* LED-illuminated tri-color, flush-mounted front and rear class lights with raised gaskets Printed number boards with separately-controlled, backlit LED-illumination* Front EMD low plow with MU hose doors 3-hose multiple unit (MU) hose groups with mounting bracket and gladhand detail Semi-scale coupler buffers equipped with durable metal semi-scale Type E knuckle couplers Front and rear straight uncoupling levers without loop handles Square-corner pilot face with angled lifting slots, front and rear “Late” tall deck-mounted multiple-unit (MU) receptacles, front and rear “Tall” stepwells with “zig-zag” pilots, front and rear End handrails with deck-mounted stanchions, front and rear Front and rear early small deck extension Positionable straight (late) drop steps, front and rear Late treadplate 81” low short hood with ratchet handbrake Late drop grabs and standard nut-bolt-washer (NBW) mounting on nose front and top Latched battery box doors with narrow louvers and tab-style (early) hinges Early cab sub-base doors with non-terminating reinforcement ribs, both sides Dual right rear cab steps Late cab step guards (short taper) Hopper water piping underneath front battery box step Standard EMD high headlight with glare visors in numberboard housing “35-Line” cab with standard armrests, and flag holder bracket on right side (D&RGW) Detailed cab interior with separate floor, cab blowers, rear wall, early seats, and standard AAR control stand Positionable cab side windows Tall square-corner clear wind wings mounted fore and aft of cab side window, both sides of cab Standard EMD sunshades with long mounting tracks Lost-wax cast brass Nathan AirChime M3 (M3R1) horn mounted on number board housing Excalibur low-profile “ice skate” communications antenna mounted to cab roof Long hood with standard electrical cabinet seam, bolted generator compartment door, and late inertial drain hole placement (close spacing on engineer’s side, high on fireman’s side) Small ECAFB Late (ribbed) blower duct housing Late long handrail stanchion spacing with all “tall” stanchions overall Early inertial air intake grilles without drip rails Standard turbo exhaust stack Late standard-range dynamic brake housing (long tapers), with rectangular vent See-through 48” dynamic brake fan housing mounted on riser ring with 10-blade fan and hub assembly, with concentric-ring grill Dynamic brake intakes with see-through intake vanes, and resistor grid detail inside of the housing Rectangular-mesh radiator intake screening See-through standard-height 48” radiator fan housings with 8-blade fan and hub assembly Separately-applied radiator core detail mounted inside of long hood, visible under radiator fans Curved radiator fan grab iron Rear LED-illuminated horizontal headlight and standard housing Late rear sander door catch placement (outboard) Underbody frame rails with separately-applied plumbing and traction motor cable bundle details Detailed Blomberg-B truck frames (LFM-cast) with Hyatt bearing housings, separately-applied brake cylinders in released (piston retracted) position, elliptical springs, end transom detail, separate sanding lines and brackets, and separate swing hanger detail Separately-applied flexible neoprene sanding lines at both ends of trucks Rust-color painted wheelsets Early EMD speed recorder mounted to right #1 axle “McCarty” type re-rail frogs ACI labels mounted to blower duct on left side, and rear cab step kickplate on right side Standard 4 jacking pads Frame-mounted bell Salem-brand #824-170 and #818-170 primary and secondary centrifugal air filters, respectively (accordion-style) Separately-applied brake vent regulator valve and plumbing detail on underbody 3600-gallon fuel tank with late mounting brackets, inset dial gauge on both sides, and late rear drain bar Separately-applied fuel fillers, drains, and breather piping on fuel tanks Separately-applied engine oil sump drain fitting with hose Separately-applied radiator water drain fitting on underbody Separately-applied truck air line plumbing on underbody above each truck, both sides Separately-applied wireform grab irons, wireform lift rings, etched windshield wipers, trainline hoses, sand hatch covers, and more Motor with 5-pole skew-wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended Radius: 22” DCC & sound-equipped locomotives also feature: ESU LokSound 5 DCC & Sound decoder with “Full Throttle” functions Two (2) cube-type speakers Turbocharged EMD 16-645 prime mover sounds ESU designed “PowerPack” with two super capacitors**** Operates on both DC and DCC layouts
Produktgewicht inkl. Verpackung: 1,320 kgNeuerscheinung! Auslieferung Dezember 2024
Vorbestellfrist für garantierte Lieferung: 26.02.2024
Road Number-Specific ScaleTrains All-new model Era: 1970s-era Series 3086 to 3093, built Nov/1971 D&RGW 3087, 3088, 3089, 3090, and 3093: EMD square-corner “Burnham” number boards D&RGW 3092: Original EMD number boards Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-Illuminated rectangular walkway lights mounted between front and rear sanding valve doors, and round walkway light aft of raised walkway duct* LED-illuminated Mars SBW-2-301 dual signal light (clear lenses) mounted in low short hood* LED-illuminated tri-color, flush-mounted front and rear class lights with raised gaskets Printed number boards with separately-controlled, backlit LED-illumination* Front EMD low plow with MU hose doors 3-hose multiple unit (MU) hose groups with mounting bracket and gladhand detail Semi-scale coupler buffers equipped with durable metal semi-scale Type E knuckle couplers Front and rear straight uncoupling levers without loop handles Square-corner pilot face with angled lifting slots, front and rear “Late” tall deck-mounted multiple-unit (MU) receptacles, front and rear “Tall” stepwells with “zig-zag” pilots, front and rear End handrails with deck-mounted stanchions, front and rear Front and rear early small deck extension Positionable straight (late) drop steps, front and rear Late treadplate 81” low short hood with ratchet handbrake Late drop grabs and standard nut-bolt-washer (NBW) mounting on nose front and top Latched battery box doors with narrow louvers and tab-style (early) hinges Early cab sub-base doors with non-terminating reinforcement ribs, both sides Dual right rear cab steps Late cab step guards (short taper) Hopper water piping underneath front battery box step Standard EMD high headlight with glare visors in numberboard housing “35-Line” cab with standard armrests, and flag holder bracket on right side (D&RGW) Detailed cab interior with separate floor, cab blowers, rear wall, early seats, and standard AAR control stand Positionable cab side windows Tall square-corner clear wind wings mounted fore and aft of cab side window, both sides of cab Standard EMD sunshades with long mounting tracks Lost-wax cast brass Nathan AirChime M3 (M3R1) horn mounted on number board housing Excalibur low-profile “ice skate” communications antenna mounted to cab roof Long hood with standard electrical cabinet seam, bolted generator compartment door, and late inertial drain hole placement (close spacing on engineer’s side, high on fireman’s side) Small ECAFB Late (ribbed) blower duct housing Late long handrail stanchion spacing with all “tall” stanchions overall Early inertial air intake grilles without drip rails Standard turbo exhaust stack Late standard-range dynamic brake housing (long tapers), with rectangular vent See-through 48” dynamic brake fan housing mounted on riser ring with 10-blade fan and hub assembly, with concentric-ring grill Dynamic brake intakes with see-through intake vanes, and resistor grid detail inside of the housing Rectangular-mesh radiator intake screening See-through standard-height 48” radiator fan housings with 8-blade fan and hub assembly Separately-applied radiator core detail mounted inside of long hood, visible under radiator fans Curved radiator fan grab iron Rear LED-illuminated horizontal headlight and standard housing Late rear sander door catch placement (outboard) Underbody frame rails with separately-applied plumbing and traction motor cable bundle details Detailed Blomberg-B truck frames (LFM-cast) with Hyatt bearing housings, separately-applied brake cylinders in released (piston retracted) position, elliptical springs, end transom detail, separate sanding lines and brackets, and separate swing hanger detail Separately-applied flexible neoprene sanding lines at both ends of trucks Rust-color painted wheelsets Early EMD speed recorder mounted to right #1 axle “McCarty” type re-rail frogs ACI labels mounted to blower duct on left side, and rear cab step kickplate on right side Standard 4 jacking pads Frame-mounted bell Salem-brand #824-170 and #818-170 primary and secondary centrifugal air filters, respectively (accordion-style) Separately-applied brake vent regulator valve and plumbing detail on underbody 3600-gallon fuel tank with late mounting brackets, inset dial gauge on both sides, and late rear drain bar Separately-applied fuel fillers, drains, and breather piping on fuel tanks Separately-applied engine oil sump drain fitting with hose Separately-applied radiator water drain fitting on underbody Separately-applied truck air line plumbing on underbody above each truck, both sides Separately-applied wireform grab irons, wireform lift rings, etched windshield wipers, trainline hoses, sand hatch covers, and more Motor with 5-pole skew-wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended Radius: 22” DCC & sound-equipped locomotives also feature: ESU LokSound 5 DCC & Sound decoder with “Full Throttle” functions Two (2) cube-type speakers Turbocharged EMD 16-645 prime mover sounds ESU designed “PowerPack” with two super capacitors**** Operates on both DC and DCC layouts
Produktgewicht inkl. Verpackung: 1,320 kg
Angebote
Topseller
Information
